Review: GEPRC CineQueen 4K cinequad drone

[@rocheuro]

hey how did you get such a great noise free amasing FPV DVR footage recorded? - so clean! havent seen anywhere that good and clean from other youtubers

[@kevbarry6457]

What a great setting for flying near the water and at the airfield. You are placed ideally by all accounts.

[@joecaraco7503]

What a beautiful town center and park! Very nice video with no fisheye effect.

[@MCsCreations]

Fantastic flying and review, Bruce! 😃 This camera is really fantastic!

[@DavideDeRosa3383]

Hi, did you notice that temperature of the motors is too high? For me, after a simple cruising flight, the motors are so hot that I can't touch them. I tryed with a 3S 1500 and a 3S 650. With 650 the temperature is lower but still high. I don't understand how people can flight with a GoPro session on it

[@preludefpv]

G'day Bruce! Fantastic review as always! Looks like a decent quad but I really just came here to say hello 🤗👋👋 always good to see your videos mate! Take care and enjoy the cine quad! 🤩👍👍

[@OivindKolloen]

You are a bad man Bruce, I thought I had all the quads I needed but now I am really tempted 🤣. Love all your content and thank you for standing up for the great hobby.

[@LWJCarroll]

Hi Bruce which Tx did you use? I was guessing the new Jumper T16 Pro ? Thanks Laurie

[@bergfpv6486]

My guess, as to the rubber strips, would be that they're soft bumpers for the guards to make it even more soft target safe.

[@skyquads1930]

Great review, I have been following your channel for a while and have leatnt loads. Thanks.

[@johanbergkvist8834]

Bought my first FPV drone and since you liked the CineQueen, Bruce, then I thought that it was probably good enough for me too! It is. I'm having so much fun! You have introduced another RC (plane) flyer to the dark side. :)

[@jr63]

Wow super duper great little quad, maybe my next one next summer when the ship with money arrived :-) Great footage and review, thanks for sharing!!

[@LWJCarroll]

Bruce looking forward to the DJI Digital video comparison too

[@TR1S10WERTZ]

So are you flying acro without air mode while getting nice shots then when you want to RIP balls you turn air mode on? Does it come with air mode setup or you have to set it up.

[@LWJCarroll]

Brilliant review Bruce! Really pleased to see you do one as I have been watching other reviews on YT just need to check the price and can then salve me dollars and buy one, looks good for flying around the house here etc and learn with! Laurie

[@GeorgeCooper_LoneWolf]

Bruce them foam stripes are to go on the bottom of the arms, they come with all GEPRC frames and if you get a 5 inch they even give you some to dampen the cam. Great review Bruce. PS hope your daughter feeling a bit better...

[@JerryCalverley]

Looks like a terrific model for the application. Thanks for your honest reviews.

[@aarem01]

nice to see some more reviews from you!

[@wdavie27]

Hiya Bruce do you know if these kind of quads will be able to be FAA certified with they new regulations and restrictions there trying to apply :-)

[@MathewBT81]

Great review! How loud is this little drone in terms of dB's roughly?

[@LWJCarroll]

Bruce have you talked to the council about contracting aerial surveys of the water weed in the lake? It would be an accurate way of seeing any changes etc, especially as we have 1 Gig fibre around Tokoroa. It should be very easy for them to receive HD and 4K videos from yourself.. Regards Laurie

[@locoworks8179]

how long have you had this? i have just received mine and it has a tarsier V2 and the antennas are underneath running rearward at around 90 degrees apart, much better placement IMHO, . not sure how those foam pads are supposed to fit on the bumpers unless you cut them into short lengths to fit between the little gusset thingys, i thought they were to fit along the bottom of the arms to act as a damped UC.

[@EnglishTurbines]

Finally, some golden calm weather for NZ Bruce...Here in the UK, it's like living on the north face of the Eiger Mountain

[@raptorpome2577]

It could be a lot worse you could live in Australia...

[@Cdr_Mansfield_Cumming]

EnglishTurbines: I can agree with you there bud. I'm in Coventry and it's been a crap winter. We've had so much rain it's a pity it was not cheap enough to ship out to our Aussie brothers & sisters to help out with their drought! Mind you, now we have left the EU, we can go back to buying all that beautiful New Zealand Lamb the French buggers got massive tariffs on to stop us buying it. Anyway, I digress. That video of slow movement around the statue is the type of RC photography I want to do. I was especially impressed when the HGV went past and it appeared to make no difference with the air vortex passing it.

[@EnglishTurbines]

@@Cdr_Mansfield_Cumming Yes, isn't that typical of the Froggies?...So glad we are leaving the EU bastards..Now our weather shows signs of improving, we are on lockdown...I'd love some NZ lamb TBH...I can remember having it on a weekend....🤔🤔😀😀😷😷😷😷

[@CraigFlemingMedia]

How do you put it in bind mode? The bind button on installed receiver is not accessible. Please help :(

[@blancsteve4819]

Would it be worth removing the weight of the prop guards ?

[@stevenkelby2169]

Yes it definitely flies better and for longer. Only use the guards if you might bump into things. I leave them on most times because I'm indoors or flying through trees.

[@palankaizs]

Great video about this nice quad. How much is the avg flight time with this 650/4s battery?

[@LWJCarroll]

I think Bruce mentioned 4 minutes

[@scooterfpv8864]

NICE!!! #1 Just looking at this Cine drones design, fit and finish I liked it immediately. #2 Glad to know the Tarsier recording has been rendered proper in your vid for clarity of performance but mounting this little jewel with 2m holes will present a tooling challenge for either of my blanks frames that will run the Radix LI with 3m holes. Will have to flip a coin to see which one will get it.

[@GMRyan13]

Can the “GEPRC CineQueen 4K 3inch Tarsier V2 CineWhoop”record vertical down still imagery?

[@vaguedirector_7342]

For the cinequad style of slowly flying around and exploring the environment it seems like DJI FPV is a no brainer.

[@solring]

Time ago I spent a couple of months with a hubsan x4 and now I want to junt into fpv, is this drone suitable for beginners?

[@stevenkelby2169]

Yes!

[@pinguabr]

what do you use to stabilize tarsier takes? very good review as always thanks!

[@LWJCarroll]

Hi I believe Bruce is the Black Magic Designs Davinci Resolve Studio software Laurie

[@swallef1]

Would it bind with the jumper T16 , do you think?

[@rc-fannl7364]

Looking really good, as we generally expect from GEPRC. Well demonstrated.

[@felixsrcworld5112]

i like your review, good information, and i learning something every time you review a product... And nice fly by the way.👍

[@aowi7280]

What rates, super rates, expo do you use for cinematic flying?

[@Lipkoo]

my friend what is resolution used in your movie ?

[@PiDsPagePrototypes]

Would there be a gain in stability from slinging the battery underneath?

[@nono9370]

PiDsMedia nope

[@PiDsPagePrototypes]

@@nono9370 can you explain more? Putting the mass underneath would seem to be the way helicopters work best, why would it not improve stability? In race cars the mass is put as low as possible to improve handling, where in a truck it's up high, making the truck more unstable in cornering or on steep grades.

[@nono9370]

PiDsMedia in a helicopter the rotor is above center of mass...

[@nono9370]

PiDsMedia in a quad you want centre of Mass just above or just below the props

[@PiDsPagePrototypes]

@@nono9370 So below is okay then. Will it be more stable or less stable then above? Physics would suggest more stable, which would help improve the stability of the camera, meaning less post-production smoothing.

[@fpvcinematic69]

hi... how do you get 4k camera to record?

[@MnPaul1]

That FPV footage is better than what I have see in most of the caddix reviews. I wish that I could use it. My 4" cinewhoop only has room for a single board camera. I have been looking at the runcam but keep hoping for a higher res Foxeer. Give me a Predator/HD combo. My whoop flies well in wind too, as long as you remain horizontal with the ground. Get perpendicular and the wind gets you.

[@GroundControlRC]

Love the 4K Footage! See you in the Air!

[@Burn377]

Geprc make some pretty nice stuff, I modified one of their cx3's with an 800mw vtx, tbs crossfire and the runcam hybrid goes great on a 4s 850/650 my last video has flight footage from it, currently building one of their cx3 pro frames to carry a gopro :) The tarsier will do 16:9 in 2.7k at 60fps but its a 4:3 sensor so the image is linear stretch and doesn't look great. Best to shoot in 1440p and dynamically stretch to 16:9.

[@stevenkelby2169]

How do you dynamically stretch? Thanks!

[@Burn377]

@@stevenkelby2169 I'll be honest for the footage these cams produce it's probably more work then it's worth (I only use gopro's now) But rcshim has a good tutorial at this link (there's a few methods) kzbin.info/www/bejne/hningqNujL-Yn7s

[@denisecostaon]

Splendid !!!! I am so happy I have found you !!!!! Thank you so much ! Wish you all the best !!!! I am located in Brazil and will check how can I get this cinequad drones to be sent to Brazil !!!! 🙏🏻🌎🦋🤲🏻

[@NYC11435]

I would have liked for you to have shown where the SD card goes into the quad. Other than that great review 👍👍👌

[@crddrones3457]

The foam pieces are for the bottom of the carbon fiber frame not directly under the motors but the arms right before the motors ,you cut the strip to size and stick it on bottom of arm so U will have little elevation from the ground. They do fall off when you crash and they do leave sticky marks on the bottom of the carbon fiber frame 🖼 .PS.God bless you keep up the good work, us hobbyist especially the 🇺🇸 happiest are going to more than ever with the FAA getting involved they’re going to get their money regardless we just make them see a smarter way of doing it in a more reasonable without taking our personal privacy and rights away . God bless you your channel and all the viewers 👍

[@crddrones3457]

PS I appreciate your video addressing the FAA in your community and communities around the world in the US as well

[@blackbirdboy1]

I've been thinking about this little quad for a while. Does look the business.

[@LWJCarroll]

Btw xt 60 or 30 connector?

[@lashersquirrelslayer]

BEST DRONE under $200...any help? I am poor but want some advice from the pro

[@matthewfoxx6410]

Great job Bruce

[@AceHardy]

📝

[@h2o-fpv623]

Good video thank u.

[@gingermanc]

Is it an XT30 or XT60 ? looks like an XT30 - can anyone confirm that ?

[@patrickcol]

Cheers Bruce

[@johnnydepp4114]

oh no, did you just do an unboxing ? :P :)

[@hateeternalmaver]

Muahaha, loved the footage, Mr. Tokoroa Outlaw... ;D Okay, sub-law... 🙄

[@TheMadmacs]

does anybody know why higher def cams dont handle light as well as the old runcam splits?

[@PiDsPagePrototypes]

Denser Pixel Pitch from same area sensor.

[@TheMadmacs]

@@PiDsPagePrototypes so we would need a huge sensor to get the same light handling? i wonder how big it would need to be.

[@PiDsPagePrototypes]

@@TheMadmacs Big enough to have the same pixel density and pitch as the earlier sensors. The match is the area of each pixel multiplied by the number of megapixels needed for the higher resolution.

[@TheRattleSnake3145]

The Mavic Mini is 2.7k not 1080.

[@YancySmithTurboRexPerformance]

Put a ND filter on it everything gets buttery smooth.

[@LWJCarroll]

Mmm which brand etc?

[@bren42069]

Caddx makes a nd8 filter that fits over it like a lens cover

[@YancySmithTurboRexPerformance]

@@bren42069 That's the one I've been using. Haven't lost it in a crash yet.

[@yannickg6904]

I searched for the filter that covers both lenses on BG, they only appear to carry the UV filters now, no Neutral density filter. Caddx does not list it anymore either, only the single lens filter.

[@steve_beatty]

foam strips are prop guard bumpers.....

[@thedok7333]

Sorry..!They are not😬They are foam landing pads👍

[@steve_beatty]

@@thedok7333 Well...all I know from having the Cineking and reading instructions for that model clearly saying those were for bumpers on the prop guards....use them wherever but foam landing pads disintegrate so I cobbled together some tpu ones...www.thingiverse.com/thing:3996145

[@changeagent228]

When DJI finally release the next version of their FPV system with 4K60+Stabilisation it's over for systems like this.

[@momo.ru-kun]

Yes, if they can fit it on a 2-inch cinewhoop and make it lighter. For now, it can't.

[@stevenkelby2169]

Not when you can't use it without goggles that start at $830aud!

[@changeagent228]

I tried my analogue kit for the first time in over half a year to fly a 1s round the house and was blown away with how awful it was. I don't miss the goggle cost the image looks really nice and clear. I felt guilty after ordering it thinking it was just overkill then after first flight i was happy.

[@joeys5429]

4k isoveraţed I use 1080 and 2.7 or 4k when neede who likes to work with large files

[@Testpilottim]

Mavic mini is 2.7k

[@AntsRC]

i thoght you were going to fly through the wind sock

[@LEDniac]

What receiver works with the frsky q x7?

[@sdushdiu]

Wow...what I got out of this extremely frenetic presentation was - you REALLY like this thing, and it has two different camera options and it has prop guards.S till have no idea regarding the differences in the cameras... A bit less of a frenetic presentation and a more organized coherent description of the camera differences would be appreciated.

[@aussiejonno]

Bit pricey

[@3000gtwelder]

10 charges on that Tattu and it has a bad cell..... Sounds about right.

[@evo-labs]

$400 NZD dollars!? Umm...no.

[@unnamedchannel1237]

Was going to look up the price if it is $400 no thanks that is worth more than my car.

[@yucannthahvitt]

Anything is better than digital, the lag is unbearable

[@markstephens7236]

Really, the lag on a cinequad is an issue/

[@stevenkelby2169]

Your comment made me make the face in your profile pic. Have you ever flown dji system?

[@Prop-A]

Great review, thanks 😁 this is a getter. Wish they would make flat lenses though. I am sick of fish-eye! Fish-eye is so 2010! When will it stop 🤮🤔

[@TheMadmacs]

fish eye is caused by our need to have non shaky images, but we can use lens correction when its appropriate? kzbin.info/www/bejne/i3zPl4uYd611oKM

[@momo.ru-kun]

Easy, by simply cropping it, but you lose alot of field of view