Jumper T18 How To Setup a Plane with OpenTx • (Beginners)

[@gordonsutton2161]

I have to say thanks very much for taking the time to go through the setup for us newbies. this is the first time I have ventured into computerised radio equipment so I and probably many others are grateful that there are people like yourself who are prepared to share their knowledge. thanks

[@RCVideoReviews]

You're very welcome!

[@MrPeteWatford]

Most helpful video so far. Bought Radioking Tx18s and was able to navigate much better with fewer frustrating mistakes. Now trying to set up Elevons for my liitle flying wing. Will let you if I am sucessful.

[@RCVideoReviews]

Make sure to check out my OpenTx Snippets Playlist: kzbin.info/aero/PLy3TC1ILJYTjsMsQ2YF5ZCUubv0IFiWkd Here is a video on mixing elevons: kzbin.info/www/bejne/i2GpnouGZruGo8U

[@MrPeteWatford]

Finally got my elevon setup done using Flysky I6B Rx. Had trouble with sorting out elevator and ailerons. Ailerons would work on elevator stick and elevator would work on aileron stick. Solution finally found by reversing the servos at the receiver. That got everything going in the right direction. Reversing channel direction on the transmitter would put the ailerons on the aileron stick but then the elevators were reversed, up was down and down was up. Got a headache trying to figure it out. Had no trouble setting up throttle arming switch. Next I will set up a plane with dual rates and expo. Wish me luck!

[@ParanoiaTheDJ]

This is exactly what I needed. Thank you very much sir!

[@RCVideoReviews]

You're very welcome!

[@philiproos9409]

Great for older people struggling to handle the newer style radio and not really into quads, plain and simple. top marks 11 out of 10

[@RCVideoReviews]

Thank you. Glad it helped.

[@RTatBstoke]

My T18 came in the post today and now I'm ready to start setting up my first model on it. Your Tutorial was exactly what I needed. Thank you very much :0)

[@RCVideoReviews]

Glad to help. I've got a pretty big library of OpenTx tutorials: Beginner Series: kzbin.info/aero/PLy3TC1ILJYTjqDXFB84oXVWZG14zyMYYt Intermediate Series: kzbin.info/aero/PLy3TC1ILJYThzwReZComrM-LFTa2wfiUW That should keep you busy for a while. Have fun with your new radio!

[@MrKanoto]

I have been using the Taranis radio although they both are open source there is differences. Your tutorial was a great help. Thanks!

[@RCVideoReviews]

Yes, there are some differences to be sure. The DNA is shared though so it's not too difficult to adapt. Glad the video helped.

[@lasersbee]

Excellent... Great detail on setting up AND detailed how and why explanations. Subsctribed a day ago. Keep up the great work on your channel.

[@RCVideoReviews]

Awesome. Thanks for the sub, for watching, and the comment. Appreciate it.

[@Graham_Shaw]

I don't fly planes, but another great explination on the basics of setting one up. NICE!

[@RCVideoReviews]

Thank you. There might be a quad setup in the not too distant future ;)

[@Graham_Shaw]

@@RCVideoReviews I don't fly quads either😂I'm a heli guy😁

[@RCVideoReviews]

Ahhh...Well hopefully some of the logic videos help you out. I've got nothing on Helos which is weird because that's what I flew in while in the Navy.

[@Graham_Shaw]

@@RCVideoReviews No worries, Helos are an aquired taste I think, and sadly not as popular as they once were. So you were in the Navy, Nice!! Go you for serving and defending your country👍

[@russcole5685]

Very useful video, be nice to have a recorded copy of it saved somewhere on phone or lap top for future revisits Cause some of us only buy a model once a year or so, and forget how to set up a new model. Your content is the clearest I've come across. Thanks and hello to you from New Zealand

[@lasersbee]

You can use a Y/T video downloader... Google is your friend.

[@RCVideoReviews]

Lasersbee is on it Russ: Lots of free tools let you download KZbin videos.

[@russcole5685]

@@RCVideoReviews thankyou guys, bit of an old stick here, still learning the ins and outs of this internet

[@RCVideoReviews]

@@russcole5685 Glad to help...

[@jimm5903]

Very useful thanks. Explained a couple of things I've been struggling with.

[@RCVideoReviews]

Glad it helped!

[@bohan9957]

Simply excellent tutorial. Thank you!

[@RCVideoReviews]

You're welcome. Thanks for watching and commenting.

[@serban1967]

Thanks, man. I have the feeling I'll watch this video many, many times :) Subscribed to your channel

[@RCVideoReviews]

Thanks. Glad to have you along for the ride.

[@Barbaric_Iron]

Thank you so much for this video, very informative, and to the point.

[@RCVideoReviews]

You're very welcome. Thanks for watching and commenting.

[@shadowofchaos8932]

Just getting into the hobby fpv and rc planes. Found your channel and big thank you.

[@RCVideoReviews]

Thanks and welcome. Glad you found the channel.

[@georgesheptak5657]

Can you show this tutorial on the tx16s. I think it’s close ,but not spot on as the T18 jumper Great vid. I enjoy all of them so far. Your good at explaining the details in in simplicity. Thanks for your time

[@RCVideoReviews]

I would invite you to visit my beginner playlist: kzbin.info/aero/PLy3TC1ILJYTjqDXFB84oXVWZG14zyMYYt and specifically this video: kzbin.info/www/bejne/aHvLaJKQibeGpqs PS The software setup is exactly the same for both radios. The only difference between the two is hardware layouts. i.e. Jumper has 3 nav buttons, TX16 has 4.

[@filippotenani9896]

Very well done. Do you can also add an explanation for a tipical DLG configuration Please? I think in this case there are different challenges in order to setup it. Thanks

[@RCVideoReviews]

If I knew anything about flying a DLG I’d help you out but I’ve never flown one so not in a position to offer advice. Sorry. Thanks for watching and for the comment. J

[@goldenfish77]

Very useful and excellent tutorial vodeo for OpenTX transmitters! I learned from this a lots of informations! Thank You!

[@RCVideoReviews]

Glad to hear that! Thanks for watching and commenting.

[@kkuenzel56]

Keep those newbie videos coming!

[@RCVideoReviews]

Thanks for watching. I’ll keep working on content. ;)

[@erad05]

Thanks that helped me to be able, finally be able to bind this to a 4 ch Spektrum receiver on my AHI. Now I need to figure how to configure flapperons ....

[@RCVideoReviews]

Quick demo here: kzbin.info/www/bejne/Y6Klfqema7x7qLs

[@erad05]

@@RCVideoReviews thank you. I still am “swimming”. Wasn’t really able to program flapperons. Well I’ll try again . It’s complex this open tx.

[@RumahkreatifKalibasau]

Thank you so much for sharing. Happy nice day

[@RCVideoReviews]

Thank you! You too!

[@munthery]

Very helpful. Thank you for sharing! Please do more training videos on this transmitter. :P

[@RCVideoReviews]

I have an extensive playlist of OpenTx tutorials. While I use the TX16s as the demo unit, the information applies to OpenTx in general.

[@airhammer6203]

As you know, this really helps me out a lot. I'm glad the J.T-18 lite has voice promps. Does the RM T-16s? I only watched a few of them. I'm sure others will be referring back to this and all of the open TX videos. Thanks. AirHammer out!!

[@RCVideoReviews]

As far as I know all the full size transmitters since Taranis support voice. That’s an OpenTx capability. I’m not sure about the pint size joystick style transmitters.

[@airhammer6203]

@@jimsnodgrass8454 👍👍. AirHammer

[@airhammer6203]

@@jimsnodgrass8454 I was mostly just wondering about voice promts, minutes left in flight etc...

[@patricksenn]

Thanks !!! Very helpful !!! Great !!!

[@RCVideoReviews]

You're welcome!

[@pjd.99]

Do you have a video to use that helps in setting up a Spectrum DSMX SAFE compatible model?

[@RCVideoReviews]

Sorry, no. I don't use Spektrum gear.

[@solarstrategy9967]

Followed your instructions and got the Jumper T18 to bind with Aeroscout. Got throtlle cut working as well. Thanks, worked like a charm. How do I set up the safe/beginner mode? Many thanks.

[@RCVideoReviews]

I'm not familiar with Spektrum--never bought one. However; I believe you set it up on Channel 5. So add a 3pos switch to Ch5. There may be more to it than that, but that's about all I know.

[@solarstrategy9967]

@@RCVideoReviews Sounds logical. I will find out which channel is used for flight mode. The right direction. Thanks again.

[@solarstrategy9967]

Would you be able to tell me if the Jumper T18 Pro will work with the Horizon Hobby Aeroscout S with a Spektrum receiver. Thank you. I am just a newbie and things are being delivered next week.

[@RCVideoReviews]

Yes, it will bind. That plane comes with an AR636. Flight modes go on Channel 5 and Panic goes on Channel 6. Good luck and welcome to the hobby!

[@PeterWinnett]

Hi John, I wonder if you can shed any light on this for me... I have watched most of your Vids on open TX and the TX16s great knowledge you have :) I know how to set up these little Eachine planes but I have found that I can only get them to bind if I check the "low power" button. The problem with this is that they go out of range really quick.. Do you know of a way around this?

[@RCVideoReviews]

That doesn't sound right. Have you tried ensuring your radio is a few feet away from the Rx?

[@PeterWinnett]

@@RCVideoReviews I was hoping you were right but alas not.. I have tried to bind from 10ft away and it just sits there but as soon as I change the power setting to low power it binds. When I try to bind without the LP button checked I can hear a small chirp as if it's bound but it's not. Then when I check the LP button it starts to work. The problem is on LP the range is about 50 yrds... Regards, Pete

[@PeterWinnett]

Hi, can you tell me what trims T5 & T6 are used for? Regards, Pete

[@RCVideoReviews]

My understanding is glider pilots put them to use. A glider with four aileron servos for instance, can use a trim switch for the 2nd pair of servos. I haven't found much use for them, outside of using them as momentary switches which is cool because two extra switches give you 4 extra momentary switches.

[@PeterWinnett]

@@RCVideoReviews Thanks very much, Regards, Pete

[@reginaldmcnab3265]

Great video man! You did explain things well!

[@RCVideoReviews]

Glad you liked it! Thanks for watching.

[@rolandfleig2004]

Thank you

[@RCVideoReviews]

You're welcome.

[@52griz]

Thank you. Much appreciated info about a great radio.

[@RCVideoReviews]

You bet!

[@gjg8922]

When I move the throttle the channel monitor shows channel 2 moving and when I move the elevator channel 3 moves. How can I change this?

[@RCVideoReviews]

In the mixer tab, move your throttle input source to channel 3 and your elevator input source to channel 2.

[@zayyandzikraka3833]

What is point 4 (adding Switch/Servo Delay) use for in plane..?

[@RCVideoReviews]

Watch this: kzbin.info/www/bejne/nIOanqmAZp2gnNE

[@zayyandzikraka3833]

@@RCVideoReviews Thanks for the reply and informative Video.. it help me setting up my Jumper T Lite.. i'm your new Subscriber.. 😊

[@RCVideoReviews]

@@zayyandzikraka3833 Welcome to the channel.

[@giriy2119]

May i use LCD t16 for replacement lcd jumper t18? Thank you very much

[@RCVideoReviews]

I don't know. Probably. But I don't know. I don't have a T16.

[@madbren]

Great tutorial thank you for sharing. You just got a new subscriber

[@RCVideoReviews]

Awesome, thank you! Welcome to the channel!

[@madbren]

@@RCVideoReviews by the time I get my T18 I should know most of what to do 👍 all thanks to your channel

[@tcz7742]

It would be good to see a plane setup on a Jumper T lite a very basic screen.

[@RCVideoReviews]

You know, everything I do on the TX16s radio can be replicated on the Jumper right... They're nearly identical radios hardware wise, and from a software standpoint they are identical.

[@Putra_Borneo_Jawa]

Very good content.. Thanks friend..

[@RCVideoReviews]

Welcome 👍

[@solarstrategy9967]

Thanks for that. I will try.

[@RCVideoReviews]

Did it work?

[@solarstrategy9967]

@@RCVideoReviews Thanks for the followup. Will try this weekend. I now have Aeroscout to test with.

[@Droneuncle2021]

The remote controller sensitivity is too sensitive. How should I set it up?

[@RCVideoReviews]

You can't change the sensitivity of the hardware, but you can change how the hardware emits signal to your receiver by adjusting your weights in inputs, mixes, or outputs.

[@Droneuncle2021]

@@RCVideoReviews If I change the GPS mode to ATTI mode, is it possible to support voice? Voice support is not working when I change the mode.

[@spud3746]

Firstly, thanks for your videos, very helpful to a newbie such as me. Is there a link to the T18 Lite manual pdf? I can't see one on Jumper's main site.

[@RCVideoReviews]

I don't know, I never searched for one. Not sure...?

[@DashzRight]

Useful video but The amount of fiddling and stuff you have to do to setup a simple model or the most basic stuff with these radios is beyond annoying. One of the most anti user friendly products or experiences I have had in the hobby… I got my first opentx radio last month and I find myself coming back to my flysky everytime, simply plug and play, the opposite from these opentx radios

[@RCVideoReviews]

It's not for everyone.