Predator 212 Go Kart Mikuni Carburetor Install

[@racerx143]

One thing to be aware of when installing this carb to that intake manifold. (at least with the one I have which is probably the same one everybody has..GPS or GSP is written on it...) The O-ring on the carb is really close to the same size of the opening on the intake. You really need to install the carb on the intake before you install the intake to the engine. That way you can look into the intake and center it up on the O-ring for a symmetric fit when clocking the carb. I bet if you looked inside that intake from the side that mounts to the engine looking toward the carb, It would be off center in relation to the O-ring and the opening in general. You can end up with an intake leak.

[@whitneyk5926]

Ok yes this is what is Happening with mine after install … it looked lined up but when I started it was bogging then it started leaking fuels from around the filter … so do I need to align it again ?????

[@Yt.Maddogs]

Thank you so much I did not know the O-ring is suppose to be centered with the intake pipe. Now that makes sense why you install the Carburator onto the intake onto the head engine in this order. I was having trouble getting my engine to run from reving up on its own and abnormal rpms adjusting my idle and air screw when I disassembled my intake from the head I did notice the o-ring on my carb was pinching on the bottom more than anywhere else around the circumference. I hope to get another chance getting my bike to run Thank You for this comment. 🏁

[@johnhall2747]

Hey Red Beard, because of your channel I myself bought my son a minibike and just finished building 1 for myself.. it’s all thanks to your videos and know how I was able to do this.. Thank you sooo much!!!

[@danielsidlo7377]

Ok. I'm sold. I'll be ordering one of these for my kart today.

[@BeckCurtis]

Honestly sliding the barrel in and screwing it on is one of the most satisfying things of working on engines and carbs.

[@kz6fittycent]

That cable-soldering tip was a good idea! I've been wrenching for a long time and I've never even seen/heard of that! I like learning stuff. Thanks man!

[@RedBeardsGarage]

+kz6fittycent thanks man. I just came up with it one night and it worked very well.

[@TheStryct9]

a dab of super glue works too.

[@owens8311]

Chris W this worked for me!!! Thx

[@TheStryct9]

Owen Stephenson No prob glad to help.

[@josephstevenson8714]

I have a stock 212 will I mess up the engine if I just throw a new carb on it and run. And do I have to do other things as well like flywheel, rods, piston?

[@zogthegreat]

This is a good video, but like the others, nobody shows how to connect the overflow tubes. Can you show us how to properly hook up the tubes? Thanks!

[@plumjackson293]

Was this ever figured out?? Can find any videos on it

[@peterpontzer4006]

@The Truth of the Matter generally you run your overflow right to the ground, taking care to avoid your exaust and anything else that might be hot. It should never leak fuel unless it's dirty or there's a problem with the float. 👍🏼

[@shawnbergin6009]

What notch should i put my needle on bc i have a original cam shaft nothing its upgraded

[@nathanpratt3058]

Another huge problem with the stock ones which really isn't their fault is that when pushing the engine over their rev ranges the car can't keep up and it'll start leaning out, found that out by taking meat out of the governor

[@charlieinabox1850]

Just got my predator Gov out head ported and polished and big box of goodies be here tomorrow from go power sports with the makuni carb in it thanks red for confidence to do it

[@NOAH_HINMAN]

do you have to take the governor gear out or can you just take the linkage off someone plz respond

[@WyzydzFynx]

I need to know the same thing😂😭

[@xSplooshhx1]

@@WyzydzFynx did y’all find any info on that i am in the same boat

[@chandlermosteller9873]

hey whats best, just upgraded the jet or a whole new carb? Also what if it runs too rich

[@1908Rick]

I don't mean to be critical, but you spend time on the obvious things like the air filter, but you never mention the fuel hose or those two pink hoses on the carb. Where do they go?

[@mitchellweida7679]

Will my old fuel line that originally comes with the predator gas tank be able to hook to the mikuni since the fuel line attaches on the other side?

[@RedBeardsGarage]

+Thirsty Dog Garage you may need to get a longer piece.

[@mitchellweida7679]

Red Beard's Garage that's what I was thinking. Thank you

[@92silverado32]

When installing the new carb. What do you do with the governor?

[@wusgudcuh4918]

Remove all the old stock governor stuff bc the carb has a throttle line that goes in the carb

[@ryanjohnson3173]

The carburetter rods are super easy to remove with a hammer drill tighten it on as tight as you can and put her in reverse takes 10 seconds

[@scooby3715]

If only I had seen this earlier😂

[@AlexTraxxas]

It would be much easier to just drill out the hole whole in the stock backing plate to be bigger.

[@barnett37]

Can you tell a major difference in performance?

[@jordenmaddox262]

Drill it out as big as the carb hole cause the motor hole is way bigger than the carb hole so you only want to go so far cause if you go farther you'll have vacuum leaks

[@jordenmaddox262]

@The Truth of the Matter it works good I did it to mine

[@Sp3cial3d3st]

Love your videos keep up the good work I'm doing a 212 right now im doing a mild I'll try to keep it mild build

[@joelboley2344]

What about the hose coming out of the valve cover?

[@erichillsr9086]

You should have moved the clip on the needle valve when you had the chance you'll see move it to the second one second notch from the top

[@jrbbikerx3309]

Buy a Park Tool or similar cable cutter. It is a tool designed to specifically cut brake and shifter cable and will prevent fraying that happens when you cut with a regular pair of snips

[@billwiththeb]

Hello rbg..I know prob a silly question but if gov is not removed witch way does the arm need to be..foward or back till.its almost hitting things insine??22mm on mine isn't getting wot cause my cable set up sux..lol..on a g1 cart..but it's way better with the Chinese knockoff.

[@shampoolaide9851]

hey red beard i was wondering if you could maybe make a short vid on how to tune the mikuni. i have a 212 also. mods are: mikuni 22mm, header, no gov, black mamba cam, billet flywheel, 26lb springs, arc rod, fuel pump& filter, i had the 130 main & 17.5 pilot in it but i put the stock jets back in. and ive tried moving the clip all the way up and down, ive screwed the air/fuel screw on the bottom of the carb all the way out to lean it out as much as possible and still every time i pull the plug its pitch black. it idles and runs fine tho. it doesnt cut out or backfire i can rev it to the moon and it keeps on going and doesn't fall flat. i just cant figure out why im still fouling the plug?. so yea man any info would help. oh yea and once the plug starts to foul of course it gets harder to start and i get (ALOT) of white smoke from the exhuast everytime i go to crank it. i thought white smoke was a lean problem??? so yea lol as you can see im a little confused. im assuming theres no way in hell the stock jets on the mikuni are to big for the mods i have. so yea any info you can give on how to tune these things would be much appriciated!. thank you!.

[@Makermook]

When you installed the cable on the slide atop the Mikuni, it looked like the sleeve was pulled away from the top of the carb. Is there a trick to seating it in place?

[@chasperukira901]

I will replace with mikuni carburetor. the governor must be removed or fixed in the machine. for the governor gear inside the crank , tank's

[@SRT-TAE]

I used this Carburetor but uu can’t seem to get my dirt to jus idle.when j start the Bike it jus runs away i need help

[@ScrapyardFights]

i just did the header, intake and jet to my predator 212, Ive also put a zip tie through the governor spring. what would you suggest i do for my next engine modification?

[@RedBeardsGarage]

18lb valve springs and mod2 cam

[@ScrapyardFights]

thank you!

[@TomGlander]

One more question... is there some way to adjust idle on that carb? I put one on my predator, just like your video. But don't see how to adjust the idle. Thank you.

[@RedBeardsGarage]

The adjustment for idle is on the side of the carb facing the pull start

[@TomGlander]

Appreciated. This thing runs strong now! Enjoy your videos.

[@markgraber3906]

Notice how the idle rpm skyrockets (around time 14:12) when the choke/starter is engaged? How do you fix that? Mine revs so high with the choke on, it's a race to find that tiny little choke lever before the clutch engages and the minibike rides away from you!

[@johnpopzgrace1900]

I'd like to know how to fix the same problem on mine? Thanks!

[@jacobrudniski3927]

Did you ever mess with the jets or do any extra tuning for the predator?

[@geoffeves4722]

Is there any way to utilize an arc top plate with the throttle cable? Connections? Fittings? Beneficial ?

[@lesgray3355]

Hey red beard will the Mikuni work with the factory predator gas tank and if so would it need a fuel pump or would gravity feed be sufficient?

[@RedBeardsGarage]

I have used it with one before and it worked good

[@aarongilbert6863]

Hey red beard first off I wanna say thanks for all your videos there great! I’m sorry if youve already answered this but I have a genuine mikuni vm22 carb I’m getting ready to put on my 212 with intake, header, governor removed and upgraded valve springs. I was wondering what size jets you think would work best? I live at 5000ft in Colorado. Any help would be greatly appreciated. Thanks!!

[@nikolaierikssonkukkonen9878]

Been lovin your videos lately! Am new you know. Thumbs up man!!

[@2AM_Garage]

Did you have to re-jet that at all? Or mess with the pilot jet or anything? Was it good to go right out of the box?

[@RedBeardsGarage]

+2SlickNick yeah it's basically a full performance upgrade right out of the box

[@byronjones8246]

@@RedBeardsGarage Hey red beard. I'm new to the kart stuff so I put the 22m carb on an now it idles up an when u press the gas pedal it dies? any ideas why?

[@habdman]

@@RedBeardsGarage yeah dude answer what byron says dude

[@cooltool787]

hey red beard, do i need a new throttle cable for the coleman ct200u? Its the only thing keeping me from getting a mikuni cuz I dont know anything about throttle cables or where to put the gov cable

[@Therobloxgamer11]

You can keep the stock one

[@kaylapearcey2527]

Thanks for the video, will try the carb on my next build.

[@NumTomM]

I got a mikuni carb for my predator 212cc. I have an aftermarket pipe. The carb is clean. It acts like it doesn't want to start. Then when I do get it started it idles high. I tried messing with the idle screw. Nothing. I tried messing with the air fuel mix screw. It makes it sound choppy. But it still idles high. I stood behind the bike and it throws the exhaust like baseballs. You can feel it hit you from 15ish feet back. But the 2nd I apply idle, it dies. But if I do a fast idle. It will go really high. My torque converter exploded. So I've only done it once.

[@edh7970]

Can you please tell me where you got the valve cover breather. Thank you

[@KW-td8dq]

Keep it up red beard, you vids are awesome I love binge watching them. Also I am planning to build a gocart w/ a 212 predator and I want to do upgrades to it.

[@RedBeardsGarage]

Awesome man thanks for watching

[@zracing1272]

Hey man i know this is a old video but i was wondering what types of jet i need for the mikuni and a exhaust or is stock fine

[@haydona1845]

Dont know if you have found an answer or not but I believe the mikuni comes with the correct jet in it unless you live in a high altitude area

[@zracing1272]

@@haydona1845 ok thanks

[@sandman2706]

Are there by chance any experts on jetting Mikuni carbs out there? I am just having a hard time finding anything in my online searches that is helpful. Thanks in advance!

[@Martyimgay]

Just wondering the two hoses that I have left over after putting a aftermarket filter which are the crank case hose and I think valve cover hose at very front… they were both connected to old the airbox I have a 169cc “150cc” go kart

[@catfisher420]

Nice drifting! I need to get 2 of those carbs for the dual 212cc kart that I am putting together. I need two of the manual clutches as well lol. Great video, keep them coming!

[@RedBeardsGarage]

Yes they would make a huge difference. That thing is going to be mean.

[@owens8311]

I got one of these and it has the same line coming out of the bottom. Gas comes out from there where is it supposed to go? Thanks

[@RedBeardsGarage]

+Owen Stephenson it is a overflow for the carb. It isn't suppose to leak all the time

[@Bikescameras849]

when adding a mikuni carb, the governor has to be removed, correct?

[@jayssontansey6832]

Do you have a video showing how to choose the proper jets? I ordered a mikuni for my predator 212. It has cam, intake, exhaust, and valve springs

[@RedBeardsGarage]

Yeah Im about to do that video in a week or so

[@transportesromo]

I have two questions?? What do you connect the hoses that come off the carb?? Second and hopefully you can help me out. I had an oil leak on a predator. Replaced the crank case cover gasket and still have an oil leak. Have you had this issue? I looked all over and can figure out were it’s coming from. Any recommendations on what we should do to find the issue. Thanks before hand. Great channel

[@dgrimaldo2008]

As far as the different hoses on the Mikuni, how do we know which one gets connected to what? Dumb question, but it’s my first build. I’m installing a 24mm flat side to my 212.

[@yajmuhs7853]

Hey awesome build! Questions; do I have to get a billet flywheel and/or change valve springs just to safely remove the governor? Why 22mm carb? Why not like 30? Should I go with just a straight race clutch or 30 series torque converter? Why are they called TAVs? Are the "Stage" kits kind of a waste, being that you can order everything separate? I just got my predator 212 and installed it in a engine-less Baja(um I think...it only has one downtube on the frame and it has a bicycle style seat setup and no racks or anything so really I don't know by looking at the different types which one it is) I got super cheap. I'm thinking of just doing the easy bolt on stuff, filter, mikuni carb, header, the 80ish dollar torque converter on Amazon, then I have a used chain it came with, and the the back sprocket looks alright. Then I was gonna do the governor bypass, the one where you move the spring not the zip tie method. Any suggestions or tips?

[@tilvalhalla9343]

can you post a video of you doing this on a 212cc predator on a mini bike? or if you have can you post the link?

[@marcosborne4974]

I ordered a new makuni carb for my Coleman mini bike. But it doesn't come with the throttle cable.so I'm trying to figure out which cable to get.maybe you could give me some input on that.

[@XxbossdogxX]

Is the gasket between the manifold and cylinder necessary? Because believe i had a massive intake vacuum leak due to improper gasket installation. I took the gasket off and I'm about to order a new one but if I don't need it i will try running the engine without it.

[@RedBeardsGarage]

+XxbossdogxX yeah you need it or it's just going to have bad idles

[@XxbossdogxX]

ok cool. Because I was idling at like 5000 rpm.

[@RedBeardsGarage]

Thats probably why

[@Jack-bv7om]

Is the fuel pump necessary?

[@barnett37]

Is up or down choke on this carb. Thanks

[@shawnmcintyre4773]

Good video, Thanks for sharing. Looks like its going to be a Mikuni Christmas for my go kart !

[@RedBeardsGarage]

+shawn mcintyre you will not be disappointed

[@cr-us9ch]

What do you do with the governor rod and will the makuni work with the regular fuel tank instead of the fuel pump you have installed?

[@paulspomer16]

Exactly! What do you do with the governor rod?

[@crippleguy415]

So is the flat slide 24mm Mikuni carb that much better than this Chinese 22 mm round slide carb ? More jets available ?

[@TRAIL_MIX_BILLY]

Whats the bottom hole on the carburator where it mounts to the manifold adapter. The plastic gasket doesn't cover the hole and gas pours out. Should I make a gasket to cover hole and clamp it down with the plastic Spacer gasket the one with o-ring

[@mathewshackelford8037]

The small line off the bowl, is that just a vent? I'm installing my very first Mikuni and it had zero instructions. I assumed it was a vent

[@j-ric0912]

I'll be upgrading to a mikunki for my longtail motor on the ol jon boat. The stock predator throttle setup is so jenky!

[@TomGlander]

Which direction is choked on that carb? Press down for choke? Or pull up? Anyone know?

[@RedBeardsGarage]

Pull up for choke

[@TomGlander]

Awesome. Thank you.

[@guitaristinseattle]

I'm confused, just installed a Mikuni 22 on my Predator 212. 1 - Now, it runs great when the lever with rubber tip is up. Does that mean the choke is off? I've been researching this and there are opposing answers. 2 - it starts best in the mid position then I flip up, is that normal? Thanks :). (The engine is brand new, I removed the oil sensor and governor). Why did they put the idle screw waaay under the carb? Hard to get to.

[@markcooper554]

The instructions say remove the governor where is it? what is it? Did I miss that part I want to get one of these but I'm not if I can't put it in

[@adam-davidvaught8382]

Hey RB what's up! What is the term "clocking the carburetor and filter" refer to?? How is that done and what's the purpose of it? Thank you as well.

[@RedBeardsGarage]

Some times on bikes you need to clock the carb to keep it upright. Thats where the float in the carb will work correctly.

[@adam-davidvaught8382]

Red Beard's Garage got ya! Thanks bro!

[@vintagesavoiur]

What size of Mikuni would you recommend for a coleman 196cc? How much $? And where to buy it from?

[@RedBeardsGarage]

go power sports has the real mikuni 22mm or the fake ones. I would much rather spend my money on the real one

[@jimpickett9974]

Hello, I Relly want that clutch because it is the best clutch foe a go cart and I really think it is awesome and your videos are the best so keep up the awesome content, I am sorry I don't have a Facebook account so have doing these builds you guys are awesome.

[@rgtj9958]

HEY... THANKS FOR INFORMATION ON THIS CARB...IM BUILDING A 212CC WHATS YOUR ADVISE ON HOPING UP THE MOTOR WITH A (.60) STOCKER CRANK....CON.ROD..CAM AND VAVLE SPRINGS..... THANKS IT FOR A MINI RACE BIKE.....

[@crazyjesse11]

So I have a 22mm Mikuni carb on my 212 and it seems to be getting to much gas and it come out the overflow when I’m riding it or starting it up Any ideas

[@RedBeardsGarage]

its probably the float sticking. Pull the bowl off and give it a good cleaning

[@jasoncaribou9530]

Red beard , so if I put a new mickini carb on , Do I have to buy a new cable to (bt200x) , or do I use the old one which came with the bike , I'm not knowing , please help ,Jay😊

[@peytonthomas4506]

I installed one of these like you did in the video. Although every time I start it up it Revs very high then when I turn the choke off it kills it! I’ve tried probably almost every adjustment possible on it. PLEASE help?!

[@six8271]

Peyton Thomas did you solve problem?

[@RCRWJR]

Check fer air leak notice ol' Red made a gasket between intake n' motor

[@jordenmaddox262]

Check for gasket leaks and if that's good then might need fuel screw adjusted for more fuel

[@icantcomeupwithaname8925]

After installing my mikuni carb, the motor took about 20 pulls to start, and then shut off quickly afterwards when I revved it a bit. Should I be worried?

[@DangerDavefpv]

Redbeard ur yardkart build what width tires and size front and rear,seen pictures it looks so much better

[@captinflynn2541]

i bought a mikuni 22mm carb and when i take it off choke it slowly climbs in rpms and wont slow down. any idea on what i can do to fix it?

[@RedBeardsGarage]

+Captin flynn the slide must be sticking. See if the slide is falling all the way back down

[@H3MaS11]

Stupid question but what did you use to make a gasket? Can i use a 12 pack beer cardboard box to make one and add some gasket maker? I am c9ncerned about vacuum leaks

[@joelnevarez3058]

I put a mikuni carb on my 212 predator on my mini bike but my rear wheel won't stop I put it on the lowest setting what can be my problem

[@bigzoltz]

What do you do with the left over lever coming out the engine after you take the old throttle off

[@HardcoreStupid]

You can unbolt the whole thing, but then you should probably remove the governor shaft and gear from inside the engine

[@kevinmcneil3693]

What about the linkage for the governor on the old carb? What do you do with it? The mikuni does not have a place to hook it to.

[@biostatsguy]

I just ordered the Mikuni kit from GoPowerSports. Where can I purchase the main carb jets? -- I do not see the carb jets listed for purchase from GoPowerSports.

[@RedBeardsGarage]

It has a performance jet in the card already 135 i believe

[@biostatsguy]

Thanks for the kind reply. Actually, I am interested in purchasing a set of main jets (assortment of different sizes), to fine-tune the engine. I will be running the predator 212-Mikuni at high altitude (~6000 feet above sea-level), so a large main jet is likely not ideal for my setup (i.e., out-of-the-box, the fuel mixture of the Mikuni may be too rich at top end).

[@RedBeardsGarage]

+Bill W probably so. You can call go power sports and they have a engine guy that might know what your best bet is

[@biostatsguy]

Thank you sir. I will plan to contact GoPowerSports to discuss carb jetting.

[@jameslane3680]

just got one it was a VN22 Mikuni carb but its a 26mm not a 22mm

[@kyleb6325]

So you didn't have to do any tuning or rejetting on the carb to get it work?

[@chevrolet355]

On gopowersports the mikuni kit gives you the decision of getting a 48 or a 65 mm adapter. What size do I need to get for 212? Or does it matter?

[@seanfrancisbacarra6288]

What kind off carburitor use

[@joningram1497]

That’s not a Mikuni that go Powersports is selling it’s a replica and it can be had on eBay for 30 bucks however the intake that comes with that kit is a good product but the kit that they sell is extremely overpriced considering the carburetor is a replica

[@mbrrideitlikeyoustoleit8436]

I bought this carb from gopowersports then seen they were cheaper on ebay you can get the carb and intake for $54 on Amazon way over priced ....

[@Will_it_Tech]

Yup I'm got mine for 50 on Amazon..

[@theworstgamervr]

They actually tell you its a replica to get a genuine you gotta pay 40 more bucks i hate to say but gopowersports is a overpriced joke... actually whats funny is they sell on ebay bought a throttle cable off ebay cuz it was cheaper and free shipping came in a go powersports box had all the sticker and a receipt with gopowersports on it, you'd have to be damn fool to buy it off there website

[@larryross1980]

Even the genuine mikuni thats a fake ?

[@ziggybammurphy1645]

I put mine all together and shoulda put it on a crate 😂 because i started it and it took off 😂 and climbed the wall......i have a 40’ cable and it looks good...im not sure where im going wrong adjusting it....its backed off as far as it can go...any ideas?

[@breadmenv]

So what’re the two pink tubes coming out of the carburetor?

[@Travelsto18th]

Besides the fuel line, what are the other two lines used for? And are those necessary?

[@RedBeardsGarage]

+Brad S it is the overflow lines. You don't have to have them but I would recommend leaving them on it because if it overflows and gets on something hot it could catch on fire

[@Travelsto18th]

Red Beard's Garage I appreciate you getting back to me. Great videos! Keep up the good work..

[@mlrockytop]

looking at getting a kit for a 212cc motor but not sure what is meant by the adapter size choice? 48 or 65 mm thanks for any help!

[@genecreamer3750]

I'm in the same situation. did you ever figure it out?

[@stevempro331]

I’m curious to know the answer as well. If anyone knows the answer, please share!

[@sergiogonzalez3307]

whats the main purpose of a mikuni carb plss i need help n with it work better then the stock with drill jet n to install the mikuni will i meed to removetje governor thankx plss reply

[@SKATESPOTSWORLDWIDE]

Isn’t the stock carb a 24mm so how would the 22mm be bigger???

[@Ghost88890REAL]

When I full throttle it starts to bog, but any less than that it performs best, anyway to fix that or just leave it like that?

[@jayssontansey6832]

I bought a kart with a used predator. I was told it was cammed with heavier valve springs. It needed a carb so I ordered a mikuni kit. Will I need to Re-jet at all? It also has aftermarket exhaust

[@RedBeardsGarage]

+Jaysson Tansey yeah you will have to play with the jets in it.

[@jayssontansey6832]

Red Beard's Garage awesome! I have notifications on so I'll be watching for it!

[@landonproductions2373]

Could I drill out the hole on the backing plate to get a little more power?

[@smitty6290]

So go power sports has the option for a 48mm adapter and 65mm adapter. What size are you using?

[@Edgar-and-Wrench]

can you use a torque converter on the predator after you remove that governer? i want to remove it but i dont want to be eating through belts as well

[@Edgar-and-Wrench]

btw im the guy that had the mino bike with rear suspension you saw at the dallas meet a couple of months ago

[@RedBeardsGarage]

Oh hey man. I remember you. Yeah it will work fine with the governor removed. If you watch the video where the go kart does 56mph we had the governor removed and a torque converter on it

[@Edgar-and-Wrench]

awesome. ima do that to my engine then. the thing that was holding me back was the idea that my belts would be breaking

[@TysonKlose]

Looks like a fun project! I have a baja warrior mini bike with a predator 212 and I really want to do some modifications to it. So far I've only put on a new high flow air filter. I plan on putting on this carb. What's the best top plate to use for this engine? What's a good external fuel tank (around 1 gallon) that I can mount on my mini bike? Do I need special fuel tubing to connect from my external fuel tank to the new carb? Thanks in advance. Love the channel.

[@TysonKlose]

When you add this carb to the engine and connect the throttle cable directly to the carb, are you bypassing the top plate? What breather and head cover do you have?

[@RedBeardsGarage]

On the fuel line to use just go to a part store and pick some fuel line up that fits your barbs. I make most of my engine plates out of aluminum. You can buy a engine plate on ebay but you have to bend it some to make it work.

[@TysonKlose]

Ok, thanks.

[@Devin-hz3wu]

I have the same one

[@scottb3323]

what size carburetor would you recommend for a predator 301cc?

[@RedBeardsGarage]

+Scott B 32mm

[@claytonh6997]

I have put a mikuni on my mini bike and it is starting to idle very high and will not run with the choke on what is it

[@RedBeardsGarage]

You may have to adjust it some. There is a screw on the side of the carb that you can adjust idle and air fuel ratios.

[@claytonh6997]

I have messed with that a little and it yet still does the same thing while the choke is on it was running perfectly fine the way I like it and then started idling high while not moving

[@claytonh6997]

Red beards garage it still has not changed

[@six8271]

Clayton H did you ever diagnose issue?

[@brucewiles4130]

yes SIR !!! Im wanting to no were you get the adaptor for the mikuni carb to the 212 predator engine,think you i like watching you and learn alot.

[@RedBeardsGarage]

It is a kit on Go Power Sports. Thanks for the support!

[@asphaltcowboy7868]

After installing a new Mikuni..what's the best spark plug?

[@samuelszego7619]

does installing a mikuni automatically bypass the governor?