Rekluse TorqDrive Installation for BMW 1200 and 1250

[@jczmotor4287]

Very nice, thank you very much from Spain, I ‘ve bought this week a 1250 gs and I apreciate these tutorials.

[@NachoGS]

Qué tal te fue con el embrague nuevo? Funciona diferente / mejor que el original?

[@giuliobuccini208]

Nice! All I need now is just buying a GS.

[@grahammawdsley4864]

Have you already bought the clutch?? 😂

[@AlejoAguirreDaniel]

good video, very professionally explained. 👍

[@davidives7997]

Very useful info fella. 👌

[@Rezaroth]

I wonder how much this easy fix would cost at the dealer? Thank you so much for the efforts in making this demonstration.

[@parlance.electricco]

A kidney.

[@alejandrosejas]

It cost me 2,000usd to replace my old clutch kit at the BMW dealer. 😩 (R1200GS 2013)

[@Rezaroth]

@@alejandrosejas the clutch plates alone cost around $750 in my country. I bought a Gsa now 😁

[@LMO169]

Clutch pack in the motherland is 315€ plus about an estimated 2h of shop time. My guess would be about 600€

[@allanthibodeau8114]

$1500.00 C. for clutch and .5 hour install charge

[@mikeholland1556]

Great informative video, well done 👏 👍

[@LookattheBiggerPic]

...thrilled this is now available for the R1200/50GS/A!

[@lsee6145]

Is there an internal (engine)oil seal that should be replaced at the same time? Whats that procedure? I think BMW calls it a 'shaft-in-shaft' system

[@booshallmighty]

Looks easy. Is there a catch, something I should be aware of?

[@何政洋-r2f]

Good day sir, please tell me, engine Gasket how to buy it? Tks!😊

[@leandropacheco9573]

Amigo, hice el procedimiento correctamente así que cuando apreté los tornillos al final, la campana giró un poco, luego después de presionar el embrague no se movió, ¿qué puede ser?

[@mariaeduarda-qj8pg]

hello I have a BMW 1200 GS 2013 in gear changes it is very hard and noise was only the first gear now it is almost all could give me some guidance I'm Jorge from Brazil ..

[@RekluseMotorSports]

Hello Maria, Thank you for the comment and watching our video. If you could e-mail our Customer Service Team they will be happy to answer any of your questions. Their e-mail is [e-mail]. Thank you!

[@vitalydraganov]

maybe not quite relevant question here: can I install this system on bmw r1250rt?

[@saulrvillarreal]

I found that the M6 (6 mm) screws for extraction are way too small. When I used M6x40, the screws went through the cover and onto the engine case screw hole. I then had to use extractors to remove those screws causing lots of extra work. Did anyone else experience this issue?

[@alexm4988]

Hello everyone . I need some help. I placed the clutch kit in my 1200gs LC 2015 model couple days ago and I followed the instructions , torque the bolts at clutch basket 10 N and when i was ready and started the bike i heard a dance noise from the clutch basket , time to time it stops and then back again , also when im pressing the clutch lever also stops, but no problem( yet )with rest engine behavior when im riding. What sould i do ?

[@robinsongguitars]

Heard the OEM wet clutch on the water cooled Beemers have problems, such as fast wear and slippage.. Have you found this true? Thx

[@caracausaandrea590]

Complimenti bel video, esiste il kit con frizione centrifuga?

[@robertosgrigna5147]

good morning! beautiful video! just one question .... how does the shock behave when removing the belt that compresses it? Thank you very much

[@RekluseMotorSports]

Hello Roberto, thank you for the feedback and your question. When removing the belt, the shock will spring back from compression so use caution. Please feel free to reach out with any other questions.

[@george7215]

My bike is a 2021 R1250 GS ADV (40 YEARS Edition). Thanks

[@lucariboldi6738]

where do you find that gasket for 1200 LC?

[@oalsharawi]

Hello, I live in Kuwait, where I can buy your product as there is no dealer near around.

[@jsaae]

Are all of the disks and pressure plates marked with the appropriate millimeters?

[@RekluseMotorSports]

Hello Jeff E, thank you for your response and also your interest in our products. We do not mark our plates. You would just measure the clutch pack to ensure the correct height. Hope that helps. If you need anything else, please let us know at [e-mail]. Thank you!!

[@louteix9981]

Great video, very professional. Can you tell me why they saying that to replace the clutch on the GS 1250 or 1200, that pretty much you need to separate motor? Was this in older models? Thank you.

[@hi0sandiego]

The older non-liquid cooled R1200GS had a dry clutch that needed the transmission and motor separated to replace it.

[@AleCabarga.]

Hello good day. Could you tell me where to buy the seal for the cover? Would you ship this product to Spain?

[@tchecholino]

Is this the same kit for a 2014 BMW R1200RT LC?

[@chamyefadel1065]

Vous avez placer des lamelles neuves (intérieurs et extérieurs) de l embrayage mécanique , et c est toujours facile avec le constructeur...BMW.. Algiers.. Merci !

[@williamcheng6563]

Hi, may I asking where can found the FRONT LID gasket ? many thanks.

[@RekluseMotorSports]

Hello William, Thank you for reaching out. We offer the gasket and is part# 420-391. Please reach out to our customer service team at [e-mail] if we can assist any further. Thank you again and have a great summer.

[@williamcheng6563]

@@RekluseMotorSports But nobody answer me ？

[@williamcheng6563]

At email

[@RekluseMotorSports]

Hello William, we apologize for not getting you an answer. Please reach out to our international team at [e-mail] if we can assist any further. Thank you! Reply

[@williamcheng6563]

@@RekluseMotorSports Thank you for your reply, I have emailed your instructions.

[@albertosospetti6438]

Dove si può acquistare?

[@grahammason6466]

I seen a video where the guys split the bike in half whys that this is awesome

[@jumpinjee]

Because the older 1200 has the clutch on the other side, the bike has to come apart.

[@george7215]

Congrats, your video is excellent. By any chance does Rekluse sell the Engine Housing Gasket? I need to replace my cover for the 719 Billet but can't find the gasket part number...

[@Chance-ry1hq]

My question is, why? What advantage does this clutch pack give you over oem?

[@RekluseMotorSports]

Great question. Here's a video that goes over the benefits of Rekluse TorqDrive technology- kzbin.info/www/bejne/haS2gZh7jKinr68 For more questions you can also reach us at [phone] 8AM - 5PM MST.

[@bremerd_de]

Is it recommended to install a Rekluse Clutch on an R1250R? I have yet seen installation Videos for Off Road bikes only. I like the idea to leave the bike in gear at a red light and go off just like that...

[@RekluseMotorSports]

The TorqDrive clutch featured in this video is a manual clutch pack replacement for the BMW. We are working on a centrifugal RadiusX clutch that we expect to have out later this year.

[@elliderx3]

Hi how are you ? Can you send me the chain timing marks 2017 adventure 1200 bmw

[@sneaky_ru]

My stock clutch on a GSA is going at 97K miles. What kind of life can I expect from this clutch pack?

[@RekluseMotorSports]

97K is impressive. This clutch pack should reduce heat and increase life over stock. If you ride the same exact way for another 97K this clutch will last all of that and more. Generally speaking we see 2-3 times clutch pack life with our TorqDrive products. In your case this may be a stretch but would expect more life.

[@sneaky_ru]

@@RekluseMotorSports Thanks. I'm going to give it a shot.

[@cesarcerecero4922]

Hello, great video!! Question, what is the difference between this clutch and stock??

[@RekluseMotorSports]

Hi Cesar, Thank you for your question. Our TorqDrive clutch is a clutch pack replacement meaning we will be changing out the friction disks, steel drive plates and pressure plate springs. What makes our product different is our unique steel core TorqDrive frictions disks. Our disks are thinner than OEM so we can fit more into the clutch pack (12 disks instead of 8). The benefits being more torque capacity for reduced wear, reduced heat and increased power transfer capability. Clutch feel and modulation are also improved. If you have additional questions, please don't hesitate to reach out.

[@eddykhouzam902]

Rekluse Motor Sports in numbers, how much does the torque increase. Thank you

[@kowalski2334]

@@eddykhouzam902 it has more torque capacity, meaning it can handle more torque. it does not give you more torque.

[@vincenzotrotto4344]

Bel lavoretto 👍

[@ricardonataliaenossavstrom2317]

Thanks

[@jokineitor76]

El último disco está mal montado

[@ibrahimkroglu5484]

Nice

[@couttsy222]

"Thousands of an inch"??!! People still use this antiquated measurement? On a BMW, no less!

[@motarded4214]

'Merica

[@grahammawdsley4864]

In the US of course

[@grahammawdsley4864]

Is this available in the UK?

[@RekluseMotorSports]

Hi there, our partner in the UK is CI Sport and they can assist you with getting a clutch. You can reach them at 01372 378000 or [e-mail]. Their website is WWW.CISPORT.CO.UK

[@negodograu8789]

Show muito bom

[@ThanachaiwatKaveevathit]

I need RadiusX for R1200GS lc

[@RekluseMotorSports]

Hi there, thank you for reaching out. RadiusX for the R1200GS will not be available until after the first of the year. Thank you for your interest in our products!

[@ThanachaiwatKaveevathit]

​@@RekluseMotorSports IF RadiusX for R1200GS lc ready for sell. Please told me.

[@markhpluygers2226]

It would be really nice is you told us why you are installing this clutch. I mean, what is it, what is special about it and why fit it anyway. It’s a multi plate clutch!………. explanation was obviously missed.

[@BERZERKERSV4]

And this is one of many reasons why I will never own a LC 1200GS

[@kindajal]

why? the ease of replacing a clutch pack?