Removing Car dent with Boiling water and a plunger! DIY

Showing how to remove a dent with boiling water and a plunger. Remember that not all dents are the same and some are not going to come out this way! Mine still had a little deep one at the end of the day. Doesn’t hurt to try though!

[@josebaez8637]

Hey guys if y’all have the chance to subscribe to my girls page that’ll be dope. She just started a vlog channel so tell all your girls to visit her channel and share. Appreciate y’all --> Priscilla Analiese 🔥💪🏽

[@priscillaanaliese190]

❤️❤️❤️😘

[@StephenBrewer89]

That last name tho... 🤪

[@bradcooper3306]

Hey what's up Jose? I know this is old and I'm late to the party, Lol .... But I came across your video because I have a dent to remove. Man don't pay any attention to the people in the comments trying to clown for likes. Just let it roll off your back and keep it moving 💯 At least you're Trying, Showing and Sharing content 👍🏾🙏🏾 The most 90% of them do is surf for videos that they can jump on the bandwagon with other people and criticize because they have nothing to do. Make more videos and keep going man. Subbed today.

[@abdulwaqar8712]

Did this work ..??

[@motorizedpower4132]

"be careful not to burn yourself" says the guy in shorts, tank top and sliders 😂

[@AndresEdna]

Every way he can burn himself

[@justinalexander4166]

Lol you know the water is just to get a good seal doesn’t matter if cold or hot lmfao

[@jamesdeane6052]

Uve got a point there lol 😂 i think they call it PPE 😬😷👍

[@wingers-ny3lk]

Plus wouldn't you scold yourself as its a liquid not burn yourself

[@Pman353]

@@justinalexander4166 it also softens the metal and paint so it doesn’t crack or chip

[@jayhow997]

Yes this does work and is not only done on plastic. The hot water isn't to make a seal for the plunger it's to make the paint soft so it doesn't crack along the creases of the dent . It's easier to flat and polish clear coat than it is to repaint a whole door because the paint cracked and came off in one chunk.

[@dontdoit6403]

Always wear slippers and shorts when boiling water in the area. Please remember.

[@michaelspeer1339]

He looked round to make sure no neighbors were seeing him look like a tweaker with a pot and plunger 😂😂

[@4gnetmail378]

Boiling water is one temperature, it can't be hotter unless pressurised or colder then it's not boiling. Unless at higher altitude pressures. Genius Man.

[@Joe_Gold]

You can microwave water which can heat it past 100C without boiling

[@chenzostanley8817]

Remember it can't be boiling too hot😂

[@j.danielrobles7529]

What’s wrong with that? What’s the right way then.. 🤔

[@trylessego]

@@j.danielrobles7529 LMAO

[@j.danielrobles7529]

@@trylessego exactly! So what if he said like that. Don’t be so boiling hot 🥵 😡 LMAO back at you!

[@paulthompson5416]

@@j.danielrobles7529 well boiling water is 100 degrees centigrade? So is it actually boiling water you use or not??

[@cfzheng1992]

@@j.danielrobles7529 you such a genius LMAO

[@kodiak7274]

Now we just buff out all these poop skid marks from the plunger and were done!!

[@techcloud2510]

I think he wanted to remove the poop marks from the plunger, but being too drunk he just included a car side to make his thoughts exceptional...just a Musk..

[@ayejamie23]

😂😂

[@koolpopjones6499]

Ba dum tss

[@manjeshnayak88]

😂😂😂

[@deebabyism]

😬

[@ms.c3]

Thank you much for this video. I have a small dent on the drivers side of my door (2017 Toyota Corolla) I pulled up at the gas station opened my door and hit the "U” shaped barrier next to the gas pump. I’m happy I viewed your video. Guy was asking me for 50.00 to repair this minor dent. I’ll show my son your video, have him do it for me. Again, Thank you! 🙏🏽 Unlike some trolls here making fun of you. They have no respect. Me - I appreciate your video. 👍😎

[@jamietyree4994]

It doesn't have to be boiling water, water from a hose will work just as well. The water is just to help the plunger seal better. Also a sink (red rubber one) plunger works better. I've done without any water at all before.

[@jayhow997]

The hot water is to make the paint soft so it doesn't crack at the dent creases .

[@LateNightCable]

I knew a guy who worked at a car dealership way back in the day, and said they used the old plunger trick then too. Said it worked like a charm.

[@wvsgdsidifi]

the plunger just by itself or w the boiling water too?

[@kaustubhpaul4868]

Plot twist : that's how they do it in the workshops and charge us hundreds of bucks 😶

[@StallionFernando]

Plot twist, no they don't.

[@BossKnight]

@@StallionFernando yeah, they don’t do anything

[@BossKnight]

Probably just use industrial plungers without boiling water cause i dont believe the water is needed

[@A_youtube_channel_]

They actually just spend time thinking about what other problems they can make up and how high they can charge you without you complaining too much

[@xilentjay4298]

@@BossKnighto

[@davek89666]

Proceeds to dent tf out of the door pushing the plunger hahahahaha

[@-MightyMouse-]

Should my water be a low boiling, medium boiling or high boiling? Thank you... 🤣

[@IzziedeD]

it could be all of them, but mostly just not too boiling, ok? hope that clears it up. 😆

[@banditheeler853]

Hahaha let’s just say slightly boiling hahahah

[@EngineeringLife0]

LMAOOO

[@Miguel-pv4ue]

Lm😂

[@belowme1908]

Today were gonna show you how to remove skin from your feet.

[@lisabrown8495]

Lmfao 😂😂

[@Yve55]

😂🤣🤣🤣🤣you won the best comment of the day🏆

[@waterfountainsofarizona4587]

Making sure no neighbors are looking at him plunging his car. Especially that loud mouth teasing neighbor. 😂

[@windsofchangefarm8555]

Someone doesn't understand what "boiling water" means

[@youknowme8578]

😂 but not too hot boiling..

[@Hodgson316]

He said, "you want it boiling... but not boiling boiling"

[@SteelBelted]

*brings water to the slightest boil* “This is boiling hot now”

[@Flyingdogturd]

That works on plastic not on sheet metal. Unless your driving Noddy’s car

[@IanJesting]

kzbin.infoFajicGcDuls

[@StallionFernando]

@@IanJesting that wasn't metal, that was a plastic panel.

[@IanJesting]

Sounds like metal to me

[@tylerdoepker4509]

@@StallionFernando metal panel, try again.

[@teflon_da1]

Definitely metal.

[@joshd2013]

It works really good with just warm soapy water too

[@islamjesus777]

Not too warm tho!

[@criticalpapaya]

How'd u do that?

[@joshd2013]

@@criticalpapaya pretty much the same as this method except you don't have to worry about dealing with boiling water and melting stuff

[@dcappucino9513]

He turned 1 dent into a whole dent family

[@Eric-gi9kg]

Great idea..lol Only if you have a car with Tin Foil for a body. This Won't work on an older/stronger steel body

[@ZacCjw]

Worked on my 1989 ltd crown vic, actual suction cup too. Popped right back

[@banditheeler853]

Hahaha Tun foil like the fool of oz hahahha

[@loganeugenes991]

I can appreciate this yes...and may get around to trying it out...I've a dent in just about the same place very slight too

[@966Mako]

“With boiled water” Once removed from the heat source, it stopped boiling.

[@Yesterdie02]

“Can’t be too hot or it will remove the clear coat “…….pours boiling water onto paint

[@lege46]

Counter intuitive but if you were to knock that crown down in the middle between the two dents it would have maybe came out, that’s holding most of the tension in the metal

[@yawyaw9481]

No dent in my car .. i watched to see you👀😊😂

[@bcsolorza]

Worked great good job

[@spiriitualminded]

Great job man

[@mmdoz711]

Ty,that was so helpful !

[@AKEYFACTOR]

Remember to wet the plunger to get a good hold on the panel

[@mahatmacoat7215]

Boiling water, bare feet in Flipa de Floppas and an idiot. Perfect fun viewing.

[@technodazed]

Works more efficiently with a sink plunger rather than a toilet plunger.

[@SwastikaHinduSansrkit]

Soon as I saw him wearing a pink sleeveless t-shirt I knew there was trouble.

[@got2getit204]

Oh I will be using this!

[@paulheitkemper1559]

Yeah, gotta use that slightly less hot boiling water. 🤣🤣🤣🤣

[@geniferteal4178]

Bare feet and boiling water a great combination.

[@A-HotSauce]

Naaa man ,what you do is buy aircan for your keyboard ok, wait for hot day or pour the hot water on, the turn the can upside down and spray liquid nitrogen onto the heated body part you will see blue spark as your spraying the nitrogen out and it will pop out itself. I did this repair it works paint wasn't damaged.

[@SabreRedhead]

is that a gtr??

[@IVperformance]

*immediately starts making dent worse*

[@TheNoticeable]

Oh so this is why my neighbor was doing this the other day thought he was doing a dumb tik tok.

[@jonbar140]

Make sure it's not boiling too hot. Mate water only boils at one temperature

[@StephenBrewer89]

Just a class note, water , once boiling, will not reach any higher temperature. Only way to get water above boiling temp is in a pressurized atmosphere

[@803Chief10]

What do you mean by “ it can’t be boiling too hot”? It either is or it’s not

[@txddyfarquh3916]

Just curious as to how much boiling I should apply to my pot of water?????

[@hulksmash7905]

Didn't even see a dent in the door, let me put a dent in it for you then try and use the method. Now that would be a video clip too watch and you would get more views and likes.

[@untilthen2784]

I was trying to find it too

[@joseywilds3133]

Omg everyone please do this to your car it works!!!!!

[@TecniclyAwsm]

You can skip the boiling water and use a hair dryer if you want... Unless you just like waiting for water to boil

[@alysaidarivera6338]

Cuuute!

[@vgritsak93]

What a shitty way to do it. Hopefully your door is flushing fine now.

[@tomjack4642]

You are crazy bro 😂

[@garcroo2757]

What's that Brown spot on your car door bro

[@malleusmaleficarum6004]

It can't be boiling too hot? I'm not sure what you mean. Water boils at 212°F(100°C) at sea level. Once it starts boiling, no matter how much heat/energy you put into it, the temperature of the water will not go over 212°F(100°C). The steam, however, is another story entirely

[@mfc4591]

Boiling too hot? Are you at sea level or just spaced out!

[@graemelliott3942]

Boiling but not too hot? What? Boiling is Boiling 212 degrees

[@davidyetter5409]

At sea level, in open container. As you rise in elevation the boiling point goes down. If you cover and restrict the steam, the steam temperature goes up.

[@paulheitkemper1559]

@@davidyetter5409 that's a meaningless distinction considering that he's pouring it out of an open pan.

[@davidyetter5409]

@@paulheitkemper1559 Just referring to the basic laws of physics. Nothing more, nothing less.

[@lilslicknick93]

Made the debt ten times worse genius

[@qb3666]

The way he said toilet plunger

[@elonmusk2979]

rip

[@lisas5346]

I’m going to try this. Someone punched my car and dented it.

[@Youainthim86]

So what do you do for the shit stains from the plunger?

[@harlow7895]

Am I the only one who waited for the whole door to come off?

[@harrisonwarner6437]

Wait did it work?

[@Jameschung81]

How hot should the water be?

[@Jay-xn7qg]

Remember kids, the water can't be boiling too hot! 🤷🏻‍♂️🤦🏻‍♂️

[@abican7327]

Trying to pull one dent end of putting 5 more

[@lilcrisjan]

Does it ruin the paint?

[@75clipz]

U had the wrong plunger, the purpose of that design is to push the stuff down waste tp ect, the other pulls up n sucks with out the center ring

[@rylanhundley9184]

That’ll leave swells in the paint

[@TheBasqueWasp]

Boiling water is always 100°C, otherwise is just hot

[@basilfernandez6068]

What temp is "boiling too hot"?

[@blackisback74]

As ridiculous as this video is your title got me to watch it because I couldn't believe someone would try this and think it actually works

[@brendanmccreanor7046]

Did it work?

[@kipperlane5589]

Any water work it’s just to make a seal

[@jayhow997]

No . Hot water stops the paint from cracking at the creases of the dent .

[@craigfoster7242]

Sometimes on some dints , some people.... 🤪🤪🤪

[@marksanders72]

The water don't have to be hot killer You just need suction

[@THISISYOURFAULTBRO]

Just flush the whole car down the toilet 💀

[@RJ-lk5pj]

Go inside and remove the door panel and roll the dent out.

[@markusfederico8732]

So medium boiled water is OK? Juan, kick the dent in with spike shoes and show the hack again

[@Phillipjcombs]

Um it's easier to remove the interior door panel and work the dent out with proper tools smh

[@dickfitswell3437]

Plus boiling water, or almost boiling water, doesn't heat metal enough to make it plyable like it does when poured over plastic. What this kid did was he saw a video and stole it in order to get clicks or as the "cool kids" would say, get me some "clout". I agree. Take the inside panel off and work with real tools. I think it's maybe 4-6 screws to remove the panel. I think he actually dented it more and he even paused but caught himself doing more damage

[@jbb0917]

PUT SOME DAM SHOES ON AMERICA! YOU AINT IN JAIL!!!

[@IQBALHUSSAIN-xs8ws]

Explain how that boiling water won't destroy your paint??

[@jayhow997]

The boiling water makes the paint soft so it doesn't crack at the creases of the dent. It's easier to repair dulled clear coat than to have the whole door resprayed because the paint cracked down to the metal.

[@meenam300zx]

Don't try this on Tesla, the water will go through misaligned panels and right into the car.

[@amanemisa5751]

So is it supposed to be boiling or nah? I don’t know what you mean by not boiling too hot😅. I’m British, there’s no such thing lol

[@mccoy922]

I don’t see any dent on the car at all,

[@mccoy922]

I mean there is no dent in first place on that car when he pour that hot water. This guy is trying to make a fool of everyone here just to see his video

[@GoofysBandit]

"Make sure the boiling water isn't TOO hot" "Boiling" is literally as hot as liquid water can possibly get...

[@dianar9165]

Brooo when I was in school ppl hated meee so much they hit the car like I already got bulliedddd bad they didn’t have to do that so if it works pleaseee yesss

[@flemwad]

How to kill grass with boiling water

[@CRAZYRUSTYVW]

Cant do this on a classic car

[@techcloud2510]

Can anyone tell me where is the dent??

[@milaflores499]

Why he so fine tho And packing

[@Dr.Westside]

The water is no longer boiling once you take it off the heat source .

[@andresalvarez6074]

That shit doesn't work!

[@jaychandravbhovi1984]

Is that Maruti Suzuki car. Tin ka dabba

[@golgoth7600]

By boiling water you mean hot water because it stopped boiling the instant you removed it from the heat.

[@Petrucciv]

Eso podría funcionar en mi Tesla, si tuviera un Tesla.

[@TheBasqueWasp]

Did you just like yourself? Lol

[@fallingsuncreations9270]

Yes but this only works on the newer models that are trash aluminum

[@Petrucciv]

Y se destapó?

[@kcanded]

What dent?

[@lucerofam5]

I thought the door was gonna come off with the plunger 🪠

[@ivanelgordov9099]

Bro holding the plunger way to close to the end with no gloves 😮