LG Front-Load Washer Disassembly (Model # WM3360HWCA) - Washing Machine Repair Help

[@mjremy2605]

What an excellent video!!! No music, no intro, just straight to the topic. What a joy. All so clear as a bell. You folks are the BEST!!!! Very grateful, thank you! Subscribed. Tip - if your washer leaks water, and hoses are not the issue, take out the soap dispenser drawer and give it a good wash in hot water. Also take off the top, then look for a soap dispenser thingie that looks like a distributor cap with tubes coming out of it. This also gets clogged with soap every few years. Label the tubes, label the 'distributor cap piece', then take out the piece and wash it well removing soap debris. Connect it back again, and voila, job done! No more leaks.

[@repairclinic]

Thank you for the tip. We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@madatali1]

I can not comprehend how can one do without KZbin. KZbin is a god given blessing to human kind. Thanks very much You Tube

[@Rain-Orca]

it's Neo like the matrix, trinity i need to know how to fly said helicopter, boom, here it is.

[@engrkarts4861]

There are manuals but yes, KZbin is the best.

[@matthewmiller6068]

@@engrkarts4861 even when you have the manuals sometimes they are not always clear. I've had that with my car, I have the technical service manuals but once in a while how to remove some clip is inaccurately printed or there's another trick to it seeing video can help you easily overcome.

[@JDLuke]

Thanks so much for this video. While my machine is not precisely the same, it's close enough that I was able to tear it open with only minimal problems last night. My wife had run an old rug through the machine and the rubber backing on it crumbled into a million small pieces, leading to the drain filter being clogged and the drain hose not working correctly. Once I got the machine opened up, we were able to determine that the tub to pump hose was completely impacted with little bits of rubber. What a mess! Anyway, I can now see a reasonably clear path to getting everything working again, which cost me a bit of time but saved me a great deal of cash.

[@dam4274]

This might be long but this video was a great help. I found this video and used it to remove the front panel because the drain attached to the washer door boot at the bottom was clogged. I believe this is a design flaw since it stays clogged with hair and dirt. Don't know what the purpose of this drain is other than aggravate the customer. I have to daily pull hair out the hole and sometimes stick a long tool in there to work more hair up. The tube makes two 90 degree turns, one to the left and then to the right; that's why it's so difficult to clean without having to remove the front panel! I'm going to have to remove the front panel again, clean the tube, of course reverse procedure and this install a filter in that hole! I'm tired of this! I'm thinking of making a video of this myself!

[@lizpaiva6315]

my washer just clogged and turned itself off with some water inside. the small tube in the bottom-left is also clogged (we live in a beach town and the clog feels like 90% sand), and i can't use a tool to unclog it, so i'm glad this video was here to show me how to remove the front panel and fix the clog, as you mentioned!

[@KuttySivan]

Dear Repair Clinic Team, Thanks for the video. My LG washing machine 7KG , which I have been using from last 6 years, the hinge holding the glass frame broke, also the glass cover too. The LG technician told me to discard the machine as there was no parts available according to him. I couldn't find a reason to throw away the machine as It was working ok. I manage to get a second hand glass cover and a hinge. But I didn't know how to open the machine to fix it as the nails which holds the hinges were tight and it was difficult to remove them, even with rust remover. Hence, I used the machine with a rope around for few months until I saw your video. Your video showed where to open, how to open the machine safely. I removed the front sheet, took it to a welding shop where they heated the nuts and it was easy to remove them. So finally I fixed it. The machine it now running like a race horse. Thanks to you. you own every bit of the appreciation. You have saved my money to buy a new machine. I spent only $14 (QR 60) and made me feel confident. Thanks to my father for the support. Only one question arises in my mind. Why the company technicians do not support after the warranty period??? Keep up good work! thanks and regards SK

[@chillynites1]

Still very useful in 2024 ! Not my exact model, but close enough that I could logic my way through my machine's cabinet disassembly. Thank you !

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@rjbigjazz]

Thanks for posting this video. I got a repair manual and it was very confusing, but this really showed how to take it apart very easily. I would recommend to anyone needing help or parts.

[@davedei3955]

THIS VIDEO IS SO HELPFUL!!! Thanks Repair Clinic for showing the most important steps with no BS!

[@Lynn-yb9sd]

Thank you so much. This video has just helped me get 'the very stuck' detergent drawer out of my machine - I was only able to open the drawer approx 1cm, but by taking the lid off the machine and being able to get to just get to the screws holding in the front control panel I was able to remove it enough to wiggle and get my fingers in to remove the obstruction and free the drawer. Thank you again.

[@bootsforever]

Just used your video to get to a detergent cap that went into the intake, saved me hours and probably hundreds, thanks!

[@repairclinic]

Awesome!

[@cdf6333]

Thanks a lot for doing this. It wasn't just the $200 I saved, I didn't want to wait 7-8 days for the repair service and hope they had the right hose with them or add a few days.

[@luchalibre82]

When re-assembling, you forgot to mention to re-install the screws from the front control mounting panel! I know some people might forget and get confused. Just FYI, if nobody has mentioned it. But, other than that, this video has really helped me out. Thank you!

[@repairclinic]

+Arett Zuniga Hmm, we see it being done at 2:55 of the video.

[@luchalibre82]

Thank you for showing me!

[@michaelbradley9211]

Thank you guys, this video is awesome. It helped me save tones of money and have the pleasure of working on and fixing my washing machine myself with my son. Thank you !!!

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@thepeasantknight4081]

Thank you so much! You saved us a week and a half waiting for our warranty repair man to come out! A+++

[@repairclinic]

Scott Jack Awesome!! Congrats!

[@stephanieurick8820]

"Click", I love that sound in the video where they just easy breasy remove and reinstall the door latch plug. Meanwhile, I'm over here, breaking a sweat trying to turn and contort my body every which way to get the best handle on this thing, as I am trying my darndest to get it to go up and into place. It's difficult to push in there. It's definitely not a cute little "click". 😂 Great video nonetheless! Thank you so much!

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@ericx1442]

Very helpful. I didn't have the spring expander, but made it work anyways. Thanks for posting the video. Exactly what I was looking for.

[@repairclinic]

You're welcome! If you would like to give us a review, here is our link: g.page/r/CcVUrahZNozMEBM/review Have a great day!

[@prestonboling1427]

Thank you for making this video and thank you LG for making it so simple

[@priscillameijer3937]

The plate of the digital clock in mine was moved, due to this I couldn’t see how many time it would take to do a cycle. With this video I fixed it 👍🏻 thankyou

[@onecreativecriminal]

Thank you so much for posting this video, after watching your video I was able to disassembled my LG front loader and repaired (front power button misalignment) it myself.

[@fryloc359]

Thanks for this, I had to take mine apart because it fell off the platform I made and the lower weight broke off. I got everything back together except I forgot to [lug in the door switch, and putting that seal spring back on was the hardest part.

[@huttarl]

Good job getting those awkward camera angles, like 1:24. That helps a lot!

[@tomschisler1545]

yOU people are very good to deal with. always great videos too, to help a do it yourself person. i recommend you to all my friends and family. thank you

[@repairclinic]

That's awesome! We're glad that you were able to get the part in a timely manner and that you had an easy (and impressive!) repair.

[@garydowning4877]

This is a reply from 10 years ago...

[@javadchohan]

Thanks for the great tutorial, my bosch front loader has rust building up under the soap tray and at the bottom left corner, I want to see if I can fix it before it gets worse

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@angelicamaris104]

Thank you from Brazil! It is the second time that we use your video to change (actually, clean out of sand) the recirculation and draining pumps, that fill with sand (!). We live at the beach and sandy beach clothes and towels seem get a lot of sand into the machine, and it gets into the pumps.

[@steveswan9672]

Thank you very much! The lid removal was just what I needed. It worked on my 2009 WM2101HW, exactly as you show. Good on ya! swanny

[@scottcook6912]

I needed some direction on how to remove the front cover plate. This video was perfect. 1:53 Thanks!

[@repairclinic]

You're welcome! If you would like to give us a review, here is our link: g.page/r/CcVUrahZNozMEBM/review Have a great day!

[@drac1026]

Great video. This worked perfectly for my Kenmore Elite. It made taking the machine apart simple.

[@gasmo503]

Vxeeesrvcxreacfulk. Day Gffdsayvfxdyuvxxddcxxxxxxxxx

[@MetalDesignOrn]

Thanks for this video, it saved me a lot of headache and hundreds of dollars.

[@davidgreenaway8997]

Very helpful video, thanks. I removed the front panel to remove the front clean out drain hose (Part #5214FR4006G) that had become blocked by grit/sand. It's a pain to clean out the grit/sand but can be done. The measurements of this drain hose is 1/4"ID by 7/16" OD by 15-7/8" long.

[@repairclinic]

+David Greenaway Thank you for sharing.

[@dam4274]

I did the same thing too but it was packed with pet hair.

[@traamkumar]

Thank you so much. Helped me to find the issue of broken tub weight balance.

[@elliottlandon8420]

So unbelievably helpful

[@repairclinic]

Is this what you're looking for? www.repairclinic.com/PartDetail/Tub-to-Pump-Hose/4738ER1002A/1266823?modelNumber=WM1832CW

[@renewilliams6410]

It would be helpful if there was a video showing how to take the drum out (all the way) properly.

[@davidburroughs2244]

Thanks! That access worked for me, fortunately was one of the four connections of the block-type switches that was slipping lose, and that was it. Will have to plan for bending a locking clip, or replacing both ends, if that doesn't work well.

[@jules71Qc]

Hello, very helpful video. Is there a way to access the inside of the control panel? I have difficulties starting a load, hutton seems off, it is an easy fix I just need to access the contact inside.

[@prajaktapatil5951]

I watched this video because I had mice in my washing machine🤣🤣🤣🤣🤣🤣

[@abdulrahmani9238]

Everything was explained perfectly except how do you replace the door on to the new panel? I need to do that cause I am putting in a new front panel. I am wondering how do you attach the door to it

[@jpmendoza138]

Thank you for saving me money! Parts ordered!

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@pedrochip]

Thanks for posting this video. It was exactly what i needed!

[@delosallen]

This video was a life saver

[@oscartmic]

Thank you for this video. The small black drain hose accessible by the plastic front panel was clogged and I had no idea how to get to to it to unclog it.

[@repairclinic]

+oscartmic Good work!

[@Deutschtown]

Very helpful. I need to remove those heavy counter weights so I can lift the washer up stairs. Way to heavy for my old wooden stairs out back!!

[@lolfriends6402]

Can you tell me how to fix the LG front load washer when the problem will do the code word is LE

[@sureshroy2968]

Excellent video, going through all details. I was able to open my LG washer. Thank you.

[@repairclinic]

Cool thanks!

[@davidalexander4094]

Very good tutorial on taking apart machine I have just fixed my machine in 2 hrs. and saved myself alot of money! Some days your the bird some days your the windshield yaaah.

[@repairclinic]

David Alexander We're glad we could help!

[@j.morrison73]

I particularly went to this for removing the top of the front loader for access to hose connections. Bummer

[@bonsaifury]

Dude me tooooo

[@non.ya.business3610]

My control button to the power acts like it is dirty or has soap in it, I have to push it several times to get it to engage. I will have to take the front off to see if it is possible to clean. This repair video doesn’t show this but it helps to get me there, will just have to wing it. Thank you for the video.

[@garydowning4877]

I love the fact you have detailed videos. However, I have one problem that does not include removing the motor on my LG Dryer. I think it's called a relay. My Dryer starts and then suddenly SLAMS to a stop, trying to start again a few seconds later. My question is how do I fix that without pulling all of this apart?

[@repairclinic]

That would be your best bet, yes. Listen to the washer when you run a cycle after removing the shipping bolts to make sure that nothing else is damaged.

[@MelodicMizeryPs3Vids]

my dispensar drawer lining on the inside of machine came bent day one. i dont know if that can even be pulled out and replaced or if i need a whole new unit. everytime i pull the tray it gets stuck. lg's assembly line is awful

[@geosoub]

If i want to open it ( right or left side only) to remove and clean the rubber pipe which connects to the pump do i have to proceed to all this steps or less?

[@ProjectMATHEW]

Is there a way to pull apart the control panel? The screen has shaken off on mine and the digital display is now unreadable and was wondering before I started pulling it apart if it was possible to get it all apart and re-glued without destroying it, and also to know how long it may take me

[@eAGer4]

This is a great help, I now know how to get in and out safely. My problem is the machine (Same as in this video it seems LG12576FD) stopped cycle sometime through the night. There is NO power! The board does not light when pressing the power switch. I have emptied out the water but I am not getting any power. The wall socket is fine so not circuit breakers. What could be the issue?

[@repairclinic]

+eAGer4 We would look for a defective noise filter with a blown line fuse. The noise filter is circuit board looking part right by where power cord comes into machine.

[@eAGer4]

+RepairClinic.com The repair guy replaced the main PCB at the rear. I am beginning to think these PCB's have a problem with the heat/cool cycle and circuits are lifting from the board over time :-( I have now had the front and rear PCB's replaced on this machine within 3 years

[@repairclinic]

You’ll find free, model-specific troubleshooting and how-to help in our advanced, easy-to-navigate Repair Help system on our website. Please see the link in this video’s description. I hope this helps!

[@limitlesboard8381]

RepairClinic.com replace water inlet valve

[@repairclinic]

We unfortunately do not have a video for the drain hose replacement on this exact machine. We do have that replacement on a similar machine though. If you search for part #1268108 on our website, you'll find the part replacement video at the bottom of the page.

[@ouchdamn4026]

Thank you very much for the video!

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@bestelectricals4739]

Nice demo ☺️

[@toddjandro4469]

Exactly what I was looking for. THANK YOU !!!

[@repairclinic]

Todd Jandro Thank you.

[@joebaemcs]

very sweet... I am having problem with my door hinge (top) for it has corrosion all over it and the door wont' close. This vid will help me get to it. then I can check for other issues as to where the corrsion is coming from....

[@vikbhatia9051]

Thank you for the video. Very helpful for getting to the thermistor when a "tE" error was indicated.

[@timbutler1115]

The washer is not pulling the bleach or the softener from dispenser. I removed the tray and made sure the holes were cleaned and open in the dispenser tray and syphoning holes were open but still doesn't pull it out. Even water down softener per LG web site. Any ideas. The vide was very helpful. do I need to replace the dispenser unit?

[@repairclinic]

Water flow from the valve is what starts the siphon. The water valve may not be letting enough water to flow through the dispenser to make the bleach siphon out. You can also check the water lines to the dispenser the make sure they are not plugged up.

[@timbutler1115]

What would make the lines clog? I have a water softener but I notice that it gets mold in there

[@sunriseboy4837]

Very grateful. Thank you.

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@repairclinic]

Great! We're happy to help.

[@MrBigglessworth]

Do you have a video that shows how to access a front loading washer from LG and thermistor check/replacement?

[@TheFusEE]

Hi Repairclinic, your help will be greatly appreciated. My mother forgot to take away the shipping bolts before starting the same LG machine as you have posted in this clip. She washed the clothes twice in this machine. When I visited her, she complained about the washing machine jumping, so I had a look and removed all the shipping bolts. As i did expect the screws were not complete (partially destroyed). Is the best way to get rid of the destroyed pieces is through opening the rare panel?

[@antt1x]

My machine is holding the control panel onto the frame pretty tightly. I’ve removed the clips, but something in the center behind the big knob won’t let it move. Any ideas? I’ve followed the video up until this point and re-checked each screw

[@jayantisahu5440]

Can you please send lg pedestal washer repair videos. I want it very much need....

[@ngxongos]

Greetings leadership!! I like your video, are helping

[@sms1316]

Thanks for saving some money 💸💸😂😂🎉🙏

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@bepinnandan5285]

Thank you .. that's what I was looking for !!

[@SlawKingOG]

Tremendously helping video. Thank You.

[@greythinker1]

Thank you very much for the video. Very useful.

[@repairclinic]

John Smith Thanks for watching.

[@repairclinic]

Can you get a screwdriver in there to press the dispenser down?

[@IsaiasPerez2023]

Do you guys have a video that shows you how to replace the drain pump for an LG Front Load Washer Dryer WM3431H*? I would greatly appreciate the link please.

[@kevindd992002]

I have an LG FV1413H2BA washer/dryer. When I removed the water supply cable from the washer, a little bit of water dripped inside that metal rear panel that has the wifi symbol on it. I'm not sure why it's designed like this but if it is expected that a little amount of water will drip down to the inside of that rear panel, why is there a space in between the rear panel and machine body for the water to get in? And is this a big of a deal? Did I damage anything by doing that? It's just a couple of droplets and the unit wasn't plugged in when that happened a few hours ago and I'm not plugging it now until I'm sure about everything.

[@kevindd992002]

@@repairclinic yeah but how do you know when it's dry? You don't see the insides unless you disassemble the back panel of course.

[@ndembezi]

I have bought a new LG fussy logic 10.0kg fixed as per the instructions but wondering why water does not stay in the drum it flows direct to the drain. I have gone through all program to test but water never stays in drum. Any help

[@brandonsmith2437]

I have this same washer. It sat in storage for over 1 year. It smells of mildew, and the cleaned clothes do as well. I tried a few cycles of just water and bleach with zero success. I was told to remove the drain filter. How can this be performed if this is the problem? Thanks ahead of time

[@kaalinnguaqgabrielsen2736]

Can we use the washing machine to keep remove the main top?

[@dianeshanley786]

I lost my rings in this exact same washer. By taking it apart according to the video, will I be able to find them? Where would they most likely be?

[@UncleDadLovesYou]

I replaced my door gasket but did not realize that the black "gasket" on the back side of the control panel that seals the detergent dispenser was not sealing. I used silicone gasket maker from Autozone to repair it. If you remove the control panel, check the area that mates up to the detergent dispenser. It could be leaking also.

[@repairclinic]

***** Thank you for your input.

[@repairclinic]

Awesome! So glad you found it helpful!

[@Eliusalmo1]

Very useful information ! Thanks..

[@repairclinic]

Eliusalmo1 You're welcome.

[@carnini]

any videos of the back part of the machine? The rotor assembly went but upon inspection the shaft that it slides onto is worn. Looking for that part and a way to disassemble that part

[@repairclinic]

+Chris Arnini The shaft is on the inner tub. You would take both front rear panels off and remove the suspension supports and springs to get the inner and outer tub assembly out. Then remove all the bolts holding the two halves of the outer tub assembly together to access the inner tub.

[@carnini]

+RepairClinic.com is that a part that is for sale? I noticed the splines on mine are very stripped and I am wondering if this is going to be a ton of money to repair

[@bshaw7528]

Can you post pics or video of the door gasket drain hose replacement? where does the hose go after it goes under the balance weight ? where does it connect? The LG exploded view diagrams do not show this at all that I can find.

[@anjujinagel3059]

Thank you

[@artourbeliaev9081]

Ty.

[@repairclinic]

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

[@EdwardDennisFogell]

I have 2 LG WM2101H front loader washers. Both developed the same problem at the same time a year and a halfthe washere power up and eveything but afetr you select a mode you have to keep pressing the start up button several times before it operates. Finally one one the washers doesn't work at all after it powers up no matter how much yoy press the start/pause button. Now when U turn the select button to cotton/towels or normal no time is displayed just 2 dashes, time ius displayed at other mode setting but does not operate. Arte we talking front panel assembly or main control board? Part numbers? Hope U can help

[@repairclinic]

The symptoms you are describing are more of a display board issue than a control board. The only way to know for sure is to do some testing with a meter. If the door latch was not working properly you will usually get a fault code. The display board for your model is part # 1528210. Cannot guarantee that will fix the problem but would be a likely source.

[@francismaligaya4036]

How to dismantle the front glass door and replace the door hook?

[@TheCasius01]

Does the warranty goes if we take off the top? In UK

[@delilah760]

hello Repair Clinic helpers! I have an LG WM2277H. The cycles are taking WAY long to complete; sometimes as much as twice as long as the timer on the front indicates. We have tried running an empty, cold load and experienced this extended cycle time. Any ideas what we might look at? Thank you!

[@repairclinic]

We recommend using the repair help section of our website using your appliance's model number: www.RepairClinic.com/RepairHelp

[@TheBuddhaDa]

had same problem try cleaning filter if it is clogged it will not drain fast enough and cause it cycle.

[@BreakingElegance]

Where is the inlet float located it looks like a grey mushrrom with a black stem i can't find it

[@repairclinic]

+Breaking Elegance We think you are talking out the pressure switch. You should be able to see it once you remove the top.

[@daveheppel5719]

my direct drive LG front loader washing machine has started to do the floor dance, i have removed the back inspection cover and noticed 3 shock absorber things , if one of these gets weaker than the other would it cause the machine to go out of balance.

[@repairclinic]

Dave Heppel It definitely could cause the machine to go out of balance. Also, check the leveling legs.

[@fx4den540]

I have well water and it seems the cold water supply is very weak... cleaned inlets in back.. but I'm guessing lines inside are clogged..are they replaceable or can they be cleaned?? Thank s

[@repairclinic]

The water valve has a smaller hole that might be clogging up. The hoses in the machine usually are not the problem. I would first try replacing the water valve. Take the cold water hose off the washer and put it in a bucket and open the valve just to make sure you are getting good water flow to the valve first. If you are not getting good water flow out of the hose you need to remove the hose off the shut off valve and check for another screen. Other than that replacing the valve should solve the problem.

[@fx4den540]

Awesome we'll try that I get back thank you for the advice

[@repairclinic]

Alright, let us know if you need any more help!

[@krishnasswami7768]

Really gr8 n hlpful. Pls let me know the name of part, three in numbers (made of cement/cast iron) bean shaped (really heavy) fixed around Tub of LG front load Direct drive washing machine. One is in front top of tub (just behind front control panel)and two around rear top of tub. I think these are for controlling vibrations & stability of WM. In my machine front one has come out with bolt and machine has become noisey n shaking badly only while spinning. Any help for repairing the same. Thanx

[@zacharyfields7654]

Can you remove the knob without taking it apart?

[@whitesheatingairappliancer7101]

Have you ever had a top not budge on model Wm2501hva?

[@Darindelonge]

We just noticed we have several dents on the top of our washer and dryer. They almost look like they got hail damage! When we remove the top of the washer and dryer can we just push against the dents from the inside to get them to pop back in place? We tried the hair dryer and icepack trick and it didnt seem to work. Any suggestions? Thanks!

[@repairclinic]

Darin Breit Remove the top and set it finished side down on a blanket on the floor. You may be able to step on it an flatten out the dents.

[@JohnAK72]

Hope to take a look inside.

[@repairclinic]

Behzad A. We hope it goes well!

[@JohnAK72]

sure.

[@repairclinic]

We have a drain filter replacement video for part #1267432. If you go to our website and put that part number in you'll be able to see the video.