Replace coil packs Ford Escape 2001-2008

How to replace the coil packs on the 1st gen Ford Escape 3.0L v6
I've used these coil packs quite a few times. ENA brand: amzn.to/3z9YUME

[@TheGaginator]

ENA coil packs I use : amzn.to/3z9YUME

[@debraheater2949]

You make everything seem so easy.

[@TheGaginator]

I guess that's good? haha. You've got this!!

[@lilinsulatorchick9665]

Dude this video just helped saved our backsides! The check engine light started flashing last night, and after panicking, my husband and I ran some diagnostics, bought the $85 coil for the misfire in #2.. watched your video 7x, paused it and played it, and TA DA!! We are mobile and it's running better than it has in a year! Thank you! We couldn't have done it without this video!! If you ever feel unimportant if life.. atleast you know you saved a family off the side of the road! ❤

[@TheGaginator]

Ha heck yeah!! Thank you for the kind words :)

[@jamessullivan9081]

What brand of ignition coils you recommend? I have an 04 Mazda tribute V6. Similar build to the escapes I hear

[@TheGaginator]

These are the best quality as far are the cheap ones go. I have personally used very many. amzn.to/490X64S if you can spend more, get a name brand : amzn.to/48Fliu3

[@johnqueen2754]

I've got a 2001 2.0 and it has coil wires and a single coil pack. Its lost fire. They've changed it later on.

[@TheGaginator]

The 4cylinder is different than the v6

[@boomerguy9935]

Doing this job is a good opportunity to replace the PCV valve which is normally hard to get to.

[@TheGaginator]

good info

[@jillstarrguinta7140]

Extremely helpful video I'm a grandmother has to work on her own vehicle and I find this to be very easy with your video thank you so much

[@TheGaginator]

I am glad it was useful to you, thanks for the comment!!

[@boomerguy9935]

I'm glad you mention that this Escape Gen 1 engine is also in the 2008 Escape which is the first year of Gen 2 (2008-2012). The Gen 2 engine has VVT (Ford i-VCT) which has a history of problems. I have the 2008 Escape and prefer this engine in spite of less horsepower.

[@TheGaginator]

True, sometimes reliability is worth more than power

[@garycalliham6643]

Thank you! Great video! very helpful.

[@TheGaginator]

Thank you for the comment!

[@curtgoehring3477]

Torque spec is important or you'll snap those intake bolts. Don't ask :)

[@TheGaginator]

Very true.

[@davehedger337]

Great video, man! This is exactly what I needed.

[@TheGaginator]

Woohoo!

[@sergiosaucedo9465]

This helped me a ton!!! Just had my engine replace and it misfiring on cylinder 2, now my problem is solved and I have my car back again!!!!!!🎉🎉🎉

[@TheGaginator]

Yay!!

[@peterkertesz6904]

thanks man,great video.just bought this van and it needs exactly this.

[@TheGaginator]

Glad it helped

[@TwistedNation01]

Did you need to gap the spark plugs?

[@TheGaginator]

I don't remember on these, but I always check the gap, and change it if necessary

[@joeystanton9900]

Would the coil packs between a 2002 and 2007 ford escape would be interchangeable?

[@TheGaginator]

Yes!

[@dirkbrown5571]

Excellent Video! Saves a lot of time and trepidation. I do have a question: I replaced all of my plugs and coils. All was well for about a week then I started getting misfire codes on cylinder 1; I’m suspecting a bad wire in the harness. If true, where could I get a new harness? What are the issues in installing?

[@TheGaginator]

Thank you for the kind words. I would say, switch the coil pack to another cylinder first just to make sure the new coil isnt bad, then do a compression test, After that you can check the harness, The pigtail for the ignition coil packs and injectors can be purchased, but no one makes a complete harness, it would have to be traced and repaired

[@dirkbrown5571]

@@TheGaginator That’s exactly what I ended up doing. On my 2001 Ford Escape, Ford tells me that the harness is now obsolete. I was hoping to replace it, if possible, Logic being that if one wire is wonky, the rest are likely not too far behind. It would be reassuring to just replace the the entire leg or harness and call it a day. I was hoping to find a source that sells/fabricates wiring harnesses but have had no luck whatsoever. If you happen to know of one I’d relish knowing.

[@xFANETORS]

So my problem is i have the same escape and my igniton coil pack on primary secondary circuit is messed up im not sure what tht means and which coils those are

[@TheGaginator]

This may be a wiring issue, not a coil pack problem. Coil packs do not throw circuit codes typically. They cause misfire codes.

[@allanhonaker5176]

Ok how hard is it to change to plugs and back valve cover gasket

[@TheGaginator]

Not hard.

[@adrianlara796]

Perfect!!thanks!!

[@TheGaginator]

You're welcome!

[@ryantaube6546]

I normally do the right thing on these boots just not in this case

[@TheGaginator]

100%

[@alyssaharmeyer6674]

How do u replace the EGR gasket

[@TheGaginator]

You have to remove the EGR valve and then you can replace the gasket

[@pmunizmelendez]

Awesome now I’m ready to do this tommorrow! Appreciate hour time

[@TheGaginator]

You got this!

[@Virtualhangover999]

Great video! Appreciate it!

[@TheGaginator]

Thanks for the kind words!

[@munsh4able]

What are the signs of a Bad coil? 🤔 🤔 I have a Escape 2005 V6, at 45mph star shaking or kicking really bad, after slow down a few times I can go over 60mph without any problem.

[@TheGaginator]

with a bad ignition coil, you will certainly have a check engine light on for a specific cylinder. Dont overlook a fuel issue also. Make sure you properly test all systems before wasting money on parts!

[@munsh4able]

@@TheGaginator thanks for your prompt response. Is no check engine light or any other, the mechanic checked the computer with a scanner and no codes at all just the many kicks over 45mph. Mechanic said is the coil pack but the notice is no pack, just 6 coils

[@Steve-si8hx]

​@@munsh4ableso did you change your coil packs ?

[@munsh4able]

I did and now is running great , no problem at all @@Steve-si8hx

[@claudecruz2233]

Great video. I need help though. I have an 01 v6 Ford Escape and I broke the fitting going into the purge vale (EGR solenoid) and when I removed it I can’t figure out where the lines run through. Could you send me a picture on Instagram?

[@TheGaginator]

I do not have any of these cars right now im sorry:(