REPLACING SOLE MOTOR CONTROL BOARD

How to replace sole treadmill motor control board
For assistance or parts email- [e-mail]
fitnesspartspro.com/
or visit www.annapolistreadmillrepair.com/
WHY REPLACE YOUR WALK BELT ON YOUR TREADMILL
• WHY REPLACE YOUR WALK ...
HOW TO TEST FOR WALK BELT WEAR
• HOW TO TEST FOR WALK B...
See more video's on our channel below / @fitnesstechnologyserv...

[@chriswilson8300]

I was able to replace my controller following this video. If you are reasonably handy you can too. Thanks Dave!

[@FitnessTechnologyServices]

Another great post.It should help others have the confidence to install their controller. Always my pleasure

[@robinseaberg7405]

Good video, sir. I had a slightly different controller board, but this was helpful.

[@FitnessTechnologyServices]

Well thank you !!!and I just put up the newer style controller

[@jjjackson5613]

Thanks for the video. I think I need a motor control board and will be ordering it from you! :)

[@FitnessTechnologyServices]

JJ Jackson Let me know if you want trouble shooting and thanks Fitnesspartspro @gmail.com Dave

[@joelaurencio6660]

@@FitnessTechnologyServices Hi Dave, Have you added Noise Elimination Board #D021333 or how to I install this pcb

[@FitnessTechnologyServices]

@@joelaurencio6660 Hmmmm that is not fun my guy wants quit every time he gets one .I don’t like it too much either if under warranty I would make them do it ? It is in the upper console nothing is marked it goes in the speaker board to speakers

[@FitnessTechnologyServices]

@@joelaurencio6660 Hi joe hope this not a repeat if it is sorry That board is super time consuming and hard to do I would get sole to do it ! But it is in console you would need to remove the back. Then the two braces then the screws that actually hold the console in .then the four screws that mount console to frame and then the two screws you can’t see behind frame and you are there . The board you have goes in line with speaker out put board have fun 😁

[@SimplyKatieAnn]

So glad I found your videos! My treadmill won't turn on at all, not even the console. I'm trying to figure out if my control board is bad. I have only the first 2 lights lighting up on the control board. Is there anything I can try before I assume I need a whole new control board?

[@FitnessTechnologyServices]

Ok thank you you will need to do a pin test please send me your serial # to [e-mail] so I can see what wire harness type you have

[@chrisboucher79]

THANK YOU!!!! love it.

[@FitnessTechnologyServices]

Well you are so welcome I have lots on sole. Please subscribe

[@stacyholtzman8197]

Use your phone to take pictures of the board and wire connections, is some wires have the same color mark them with a felt tip marker to indicate a pair or group.

[@kenwaln4508]

Sole was great about sending new parts under warranty but no instructions and the old one was pretty well burnt, so this was great. Now I need to find the motor replacement. Pretty obvious except for how to adjust the drive belt.

[@FitnessTechnologyServices]

That is great to hear ! Glad it went well . I do have a video on replacing sole motor belt if this helps please subscribe Dave

[@socheatpream1566]

Hi, my F80 2013 sole treadmill display console freezes a few seconds after power is turned on. I check the wiring all is normal. It was working fine before, but after we took the panel apart to move the machine, the problem happened after we re -assembled it back together.

[@CertifiedMr]

Hi, Thank you for your video. I have a Solo F63, it’s keeps saying LS1 low speed. I’ve fiddled with the speed sensor and tried recalibrating it. No luck still same error. Any advice would be much appreciated. Thank you

[@FitnessTechnologyServices]

Certified MR Hi MR Certified good handle name ! Ok is this with or with out some one on it if it is only while walking mostly worn belt see video understand why my motor blew . Or in your case causing error . Then it a amp draw issue .If it happens all the time then it is a signal issue does the controller have a PMW lite on left side it will flash when working . For better trouble shooting call 410 286 5566 Dave

[@CertifiedMr]

Fitness Technology Services Appreciate the help Dave. Thank you. The belt doesn’t move at all. I will try tomorrow and let you know.

[@laselotn5]

Hallo , very informative clip ..thank you soo much..could you send me the closer clear pic of colour code for the cables that connect the upper control section . .my machine was cut off those cables to the socket . Its the same board that you posted sir . (Board model B304-S13. )

[@FitnessTechnologyServices]

Well thank you very much it would be better if you send me a pic of the cut wire to my email Fitnesspartspro@ gmail.com .And that board is Do20054

[@benitoperez158]

Thanks for the video, how do I know if it’s my control board or motor that is not working? I have an F63 and the belt no longer turns, a message on the screen says “slow speed” where can I find the serial number so I can email you info?

[@FitnessTechnologyServices]

You are so welcome . The serial # is we’re the ac cord goes into treadmill Thanks Dave

[@southforkpropertiesllc6061]

Thank you for posting these videos and your guidance. I have an F85 (serial # 5858880809000364REV-00). Tripped house breaker when plugged I plugged it up. Reset the house breaker and plugged up and no power (no control board lights). Changed the control board still no power. Any ideas? Thx again.

[@FitnessTechnologyServices]

Does the controller lights come on. And only the console is blank! How about the on off switch check and see if any of the wires look burnt. I can send you voltage output to console. But only on my email [e-mail] I don’t want to be responsible if people short there unit 🤔. And you are so welcome!!!

[@joannawayton4712]

Hi - the green wire on our sole f63 circuit board short-circuited, so they are sending us a new circuit board and drive motor. this video is very helpful, but since the wire is bad, i think i have to start with replacing the drive motor and connecting to the circuit board. do you have a video of how to do this?

[@FitnessTechnologyServices]

Joanna Wayton sorry I do not the green wire is the ground and is held in by a Phillips head screw . The green wire is a ground wire and never heard it to cause a short. Just something to think about.The motor is connected by a red and white (normally )to controller . The closest video I have to replacing the motor is “how to replace sole fitness treadmill motor belts” let me know if you need further assistance. Thanks Dave Fitness Technology 410-286-5566

[@joannawayton4712]

@@FitnessTechnologyServices Ahh thank you. I looked at your video again, and it was the white wire that shorted actually. the one that is on the left side of the circuit board if you are facing it, closest to the track of the treadmill. should that video you mentioned above be helpful to me in replacing? thanks again.

[@FitnessTechnologyServices]

Joanna Wayton Ahh that makes sense . It will show you how to loosen motor same as replacing .but when white wire is burnt that normally due to a lot of heat from running belt . ? Check out my video named sole f80 deck belt amp check made easy. Hope this helps. Dave Fitness Technology

[@ericjury480]

Hi do you sell this part? Or can you let me know where to get one? Thanks for the video! Please let me know. Thank you

[@FitnessTechnologyServices]

Yes sir we sell them . Send me your serial # to fitnesspartspro@gmail .com to get right one

[@ArtnStuff224]

I have this same treadmill and two days ago while I was running it stopped working didn't turn on anymore, I plugged it to another outlet and no luck does not light up when I switch it on nor the display turn on? What can be wrong with it I opened it to check and everything looks good no loose wires, could it be in the control board or motor?

[@FitnessTechnologyServices]

REY C.M well most likely the motor controller went bad. See videos “why my motor controller blew”and both LS1 videos on my channel. Please send me serial number and ship to address to [e-mail] if want link to purchase parts. Hope this helps.Dave

[@davidcochran7400]

Need some advice on my Sole F63

[@FitnessTechnologyServices]

David Cochran please email question to [e-mail]

[@DustyFixes]

Are the control boards the same for the F80 and F85? The reason I'm asking is I have an F85 motor and an F80 control board that I'm trying to get running so I can use them on a 12" disk sander I'm building. So far I've been unable to get the motor to run. Do you know anything about re purposing these motors for shop build machinery?

[@FitnessTechnologyServices]

Doug w well they are mostly the same signal wise . Main difference is power but most work the same .But I am not familial with changing with repurposing them they need a certain Pwm signal to alter speed and dc out put to motor . I would think you would need a console to send start signal ! I would think it would be easier just to use the motor on a variable dc controller for every 10 volts dc it runs One mile per hour or about hope this helps I do have used consoles if needed Dave

[@FitnessTechnologyServices]

Oh and must be one heck of belt sander to need that motor 🤔

[@miguelsandoval4410]

Hi how are you just bought a brand new F63 Sole, out of the box started showing E7 on the screen and stops. I reclaibrated it many times but it sudenly stops. Shows E6 and E5 some times too. I checked the speed sensor it has continuity... but the borad leds do not flick when the magnet pases near the sensor. Where i live the dealer does not provide good service... what could it be?

[@FitnessTechnologyServices]

Hmmm you will need to call sole for parts even if you don’t get service ? The E/6 is a component on the lower controller E/5 is bad communication on that check for short on main wire harness or very high resistance on one of the conductors. E/7 is bad power code or low power ? Make sure it is not in a gfi outlet after that sole line is 1-800-258-8511

[@miguelsandoval4410]

@@FitnessTechnologyServices thanks yes i am really frustrated

[@Oak690]

Sole F63 stopped suddenly and won't power on - was sent a brand new display under warranty but the new display did not solve the problem. When powered on the display flashes and that's it. I have a feeling the control board died. Would you agree?

[@FitnessTechnologyServices]

azucho98 Well normally that is in the display sorry that did not work hard job ! I would have the wire harness sent to you also . Just in case and yes the next step is the controller .

[@kristinevera6027]

We keep having our treadmill stop and we get an E-2 error on our machine. It ususally happens when a person around 250 lbs or heavier gets on the machine. We have done everything, re-calibrated it, checked the speed sensor, changed out the motor and it still happens do you have any other thoughts on what it could be?

[@FitnessTechnologyServices]

Sorry so late That is either lack of belt lube or bad belt send me your serial # to [e-mail] To see if I Can help

[@BatKountry]

Hi, Our neighbor gave us his Solo f60 because he forgot to unplug the main control board harness when he was disassembling and a bunch of those small gauged wires were destroyed. From what i can tell it's only on the cable side going to the control board and not on the plug side that goes up the steel arm to the console side. I tried soldering them and got it to power on but the motor doesn't spin after the countdown from 3,2,1. and 10 seconds later i get the low speed sensor error. If i rotate the belt, the error doesn't happen and i tried running the DC motor form my drill battery and it worked fine. So pretty sure i need a new harness or maybe controller board altogether. there are 2 green wires that are on that harness and i don't see one that is striped so i tried jumping them together in two diff configs. One has the the controller board clicking and cycling like it wants to turn the motor, the other method has everything looking right on the console screen but it doesn't turn the motor after the 3.2.1. count and throws the LS error. Where can i get a new wire harness for this?

[@FitnessTechnologyServices]

We don’t have the wire harness on our website.Just send your serial number to [e-mail] I have a video on finding serial number if needed

[@WoodyWorkshop-31A]

Hi, I just changed my motor control board using you instructions as a guide. When I plug it back in and power it up all it comes up with is an E5 error code. Any idea where I go from here. Sole F63 model 16008600630. Thanks

[@FitnessTechnologyServices]

I am not sure of that serial # normally it is 16 numbers . But E4 E5 &E6 are all soles new codes they are Communication and power codes after controller ! You will have to try display but I would check with sole 1-800-258 - 8511 as soon as I can get will upload more info Dave

[@WoodyWorkshop-31A]

@@FitnessTechnologyServices Thanks for the answer. I will send you an email.

[@FitnessTechnologyServices]

I am having new codes sent to my office later today will find out E /5 code and email you

[@edcalusinski7178]

I have an f63 from 2013. I turned it on one day and started running and it suddenly stopped. If I unplug wait a few seconds and replug in, the console comes up normally. As soon as I hit the start button it sounds like a fuse trip. A loud click, a single green light flash from the motor circuit board and then the console restarts with the i initialization message. I have taken things apart to get a good look at the boards and I do not see any evidence of burn marks. I do not smell any burning on the boards. Any thoughts on what might be the issue? Thanks

[@FitnessTechnologyServices]

Well I would start by disconnecting one side of the running motor and both the incline hots red /black .If it still trips with no load on it then most likely controller. Check my video on testing your walk belt. 90% of controllers go from worn walking belt causing high amps

[@jackcarter2303]

I cannot unscrew the two phillipshead screws that hold the control board to the f63 treadmill. Broke the tip off one screwdriver so I should be applying sufficient torque. Also used wd40 to no avail. Any suggestions?

[@FitnessTechnologyServices]

I just email you some hints I hope it helps

[@cjbhab]

same problem here 😢

[@binod049]

I was using my F85 treadmill in incline mode the other day and accidentally pulled the safety key, causing the treadmill to stop as expected. However, when I reattached the safety key and restarted the machine, I encountered an E6 Error. I tried unplugging the power cable and other troubleshooting steps, but the error persists. Do you know how to resolve the E6 Error?

[@FitnessTechnologyServices]

@@binod049 Hmm a E/6 should have nothing to do with the safety key. It is normally a controller issue check your controller look for burnt motor connections at the controller

[@davidlattal1885]

So the Sole tech.came out today to fix my incline,its not working period.when recalibrating get error,he told me i need new incline motor,got one from sole, i took a picture of all wire hook ups. befor i installed the new incline i saw he had it hooked uo as black red white ,black is up red com.white down I see that you say diffrent, this is a 2012 sole 63 could this wiring be incorrect the way he left it?

[@FitnessTechnologyServices]

Yes I hope all is ok white is always neutral red as far as I know is always up black is always down red is never neutral or common also if the black and red wires get mixed up it just works backwards red hooked to neutral I have never seen that on treadmill

[@davidborak5622]

I just installed a new board in my F85 and now I have an Incline error message and it is stuck at incline level 15. I have ran calibration three times and still the error message. Any ideas?

[@FitnessTechnologyServices]

David Borak well first check we’re incline sensor is installed make sure it is right port and well connected then the next thought make sure power wires on incline our right . Red is up white is neutral black is down

[@keshavantiruvallur3731]

I have a sole 63 and it’s showing slow speed and the motor is not running. Do I need a new control board? How much does it cost? Thank you

[@FitnessTechnologyServices]

Well you should do two test first if you can run your motor off a drill battery . Walk test your belt to see if it is the cause of controller going bad . I have these test on my channel fitness technology services. Controllers run around 240 .00 so you want to make sure . I have them on my web site ! www.fitness parts pro . Com

[@evajimenez9531]

Hi, is there anyway I can call you about a problem I have with my treadmill

[@FitnessTechnologyServices]

Of course The office #is 410-286-5566

[@tonyumana3580]

Hey I just got someone to come check my treadmill he told me I need a new motor circuit board but wants me to order it and it's 400$ canaidan do you know where I can get one cheaper and he always wants to charge me 120$ to put it on for me I just watched this video it shouldn't be to hard right ? Please let me know where can I order the part from a website that is legit or even cheaper please .

[@FitnessTechnologyServices]

No problem that’s way to much they sell for 250.00 and easy to put in just go to my site Fitnesspartspro.com shipping will be more expensive but way less than that . Also you should do a walk belt test 97% of all controllers go bad due to walk belt wear send me your serial number to Fitnesspartspro@ Gmail. Com And I will send you links for testing

[@mdimascio]

Do you sell a control board for a Sole E98 elliptical?

[@FitnessTechnologyServices]

Yep in general we sell all soles parts if I can get them send me your serial number to [e-mail] to make sure

[@makemlaughtilithurts1718]

where do the orange and red wire go? Kids knocked them off jumping on front of treadmill. On a Nordic Track Elite 7700 . I have a picture. Where can I send?

[@FitnessTechnologyServices]

Send your pic to [e-mail] I will see if I can help

[@thebestfam4258]

Great video on my it says LS1 low speed and won’t run!!

[@FitnessTechnologyServices]

That sounds like lower motor controller e mail me your serial # . To fitnesspartspro@ Gmail.com or pic to same email so I can see what controller you have . Thanks Dave

[@jessekac]

Any thoughts on an E-7 error message on Sole TT8?

[@FitnessTechnologyServices]

jessekac It is coded as Improper motor voltage .Does the unit run or does it give code right away ?

[@FitnessTechnologyServices]

If you want send me your serial # to fitnesspartspro @ Gmail .com So I can see what’s up on cost of new controller

[@jessekac]

@@FitnessTechnologyServices When I hit Start the fan kicks on for a few seconds then every stops and the error pops up on screen. I got the treadmill two weeks ago and it happened right away. Haven't been able to use it yet. Sole did send me the new board right away and I'm waiting for service but there's a backlog so no date set yet. I saw your video (great by the way) and got thinking I may be able to do this myself. They sent me 1x Motor Controller, 1 x Computer Cable (upper), 1 x Computer Cable (lower) and 1x Computer Cable (lower) which is different that the other one. Should I try and replace myself? Do you know it voids the warranty?

[@FitnessTechnologyServices]

jessekac So you would to have to check with sole on warranty issue . I have had lots of customers replace parts . But to be safe check with them . I think the controller is pretty easy to do ! I can help you on that . If you assembled the unit your self then you can install the harness for sure you already have ! What code pops up ? Call if you would like more help 410 286 5566 thanks Dave

[@richardpeters8100]

My f80 Thread mill stops after two minutes under load. I replaced motor and still problem stopping. What could be problem.Not lube.

[@FitnessTechnologyServices]

Hmm most likely it is the belt after a few years it needs to be replaced. And lube no longer helps see video on my full channel fitness technology services . Look for wear see if it is harder to push it in center than on side . I also have a video on correct amp for unit send me your serial number for belt size send to [e-mail]

[@jorgegrealty]

Do you sell parts for xterra tr 6.65?

[@FitnessTechnologyServices]

Just send your serial number to Fitnesspartspro@gmail .com let us know what issue and we will be good to go

[@bls2935]

I have a 2010 sole f80 and when I press start button the walking belt only move for a second and then stops and I get a message that says “end of workout” could you please tell me what’s wrong with it? I’m mechanically inclined and I should be able to do what you tell me to. Thanks

[@FitnessTechnologyServices]

BLS I have never seen that I will try to recreate that and get back to you . My first guess stop button is bad . try it in different programs and run unit with out someone on it

[@bls2935]

Thanks for the reply. I forgot to mention that I if I try to put it in a workout, the treadmill starts but after a second stops and I get the “end of workout message “ message. The other thing I forgot to mention was that when I turn it on and I push any of the incline or speed buttons the treadmill the treadmill starts just like when I press the start button , but stops right away.

[@FitnessTechnologyServices]

BLS So that’s not good that is hard to say . Now it sounds like main console has gone bad . Will be hard to recreate that ,fist step would be upper display

[@FitnessTechnologyServices]

Try removing back cover lots of screws 😒unplug each wire harness one at a time and see if there’s a short, sounds like console to me. Hope this helps, Dave

[@hasuckle]

My Sole F63 will stop in the middle of a run and I get a LS1 error. If I urn off power it resets and works again and eventually the same thing happens.

[@FitnessTechnologyServices]

This sounds like either low on lube or walk belt is worn . Run unit with no one on it if only happens with user on it then belt or lube send us your serial# to [e-mail] I will send you some links for troubleshooting if want thanks Dave

[@jacknthebox3723]

Hi my F63 powers on but the display/ console doesn’t come on. Is that my control board? I can hear the beeps when I plug it in but no display screen.

[@FitnessTechnologyServices]

Hmmm that can only be the upper display or the whole console depending on how techie your are

[@jacknthebox3723]

I may have forgotten to mention that although the power is on the display is not, the treadmill will not work. Is that still the console?

[@FitnessTechnologyServices]

@@jacknthebox3723 for sure

[@FitnessTechnologyServices]

It would be best to replace console

[@davidlattal1885]

replaced the incline motor and now the controll board and still error? thoughts

[@FitnessTechnologyServices]

Hi David did you recalibrate unit ? If so does it go right into error or move some first let me know

[@FitnessTechnologyServices]

Send me your serial # to Fitnesspartspro@gmail .com so I can better help

[@mrdavid30066]

yes recalibrated showes incl err,but no code,does not move at all ,unplug unit turn back on says incline err immediatetly on bottom of screen press stop to bypass.Sole say said its the council,I have replaced incline motor and now board.

[@FitnessTechnologyServices]

Send me your serial# to fitnesspartspro@gmail .com so I can see what system you have

[@amaya4car]

My Precor 9.33 Treadmill stopped working with an error code 22, I have tested the motor with a DC battery and is working fine but when I press the Start running button it gives me error code 22, can you help me please

[@FitnessTechnologyServices]

I am sorry I don’t know the precor codes . In general this sounds like a bad controller if you call the shop 410 -286-5566 they can give you precor phone number

[@ayotundeolaotan9526]

How do I find the same model

[@ayotundeolaotan9526]

My goplus fitness treadmill needs the motor controller replaced but I can’t seem to find the same model

[@FitnessTechnologyServices]

@@ayotundeolaotan9526 Never heard of a goplus. Please send us your manufacturer name, the model number and serial number and a picture of your motor control board and we will try to help you. Thanks Dave

[@FitnessTechnologyServices]

@@ayotundeolaotan9526 send to my email [e-mail] Thanks Susan

[@FitnessTechnologyServices]

send to [e-mail] Thanks Susan

[@jackcarter2303]

We used WD40 Plus to spray the screws. Then using a drill worked.

[@FitnessTechnologyServices]

Great idea thanks for posting

[@shawnkhan7866]

There's an issue with my treadmill. As soon as I plug the switch. The treadmill after INITIALIZATION starts 3 2 1 and starts automatically without me selecting manual or anything. runs on speed 1 and no buttons work at all. I can go into the factory settings but the buttons don't work after its in the menu. Since you deal with sole treadmills. I hope you maybe familiar with this problem. I will be happy if you can help me. The model is sole F85 and is 2013 model as you have in your videos.

[@FitnessTechnologyServices]

Hmm this sounds like a bad console to me .try unplugging and replugging unit to try and reboot console if not you will have to open console back and reseat main wire harness a few times .If no luck you need to replace console.Send me your serial number to fitnesspartspro @gmail.com so I can look into it

[@shawnkhan7866]

@@FitnessTechnologyServices thanks for replying. How do I reset the the console and how do I find the serial number sir?

[@FitnessTechnologyServices]

Just unplug it a few times # is in front by power switch

[@shawnkhan7866]

@@FitnessTechnologyServices I mean from where can I reset the console sir?

[@FitnessTechnologyServices]

@@shawnkhan7866 Hmm you would have to remove the console back and unplug the main wire harness there is no reset button just hopefully just to get lucky

[@oneguyatthesametime]

I have a sole f80 showing an e4 error. As soon as I hit start I hear a click then the error comes on.

[@FitnessTechnologyServices]

Hmm this sounds like a bad controller. Run your motor on a dc power source see if it seems normal. If so then you need to test your walking belt for wear! Issue with either of these can over heat controller and blow controller send me your serial number [e-mail] ....And I will send you links for testing

[@4Cranleigh]

My F85 control board shows two green lights when I turn it on and that’s it. I can’t switch the treadmill belt on. If I switch it off and on there’s a click. The console sometimes flickers.

[@FitnessTechnologyServices]

Sounds like a bad controller see my video on troubleshooting sole motor controller I would need your serial number sent to [e-mail] to see what you take

[@4Cranleigh]

@@FitnessTechnologyServices thanks. I just heard it beep like it’s going to start which is unusual.

[@4Cranleigh]

And now it’s working again, probably briefly.

[@4Cranleigh]

Just stopped. Says LS1.

[@FitnessTechnologyServices]

@@4Cranleigh try to run unit with no one on

[@cjbhab]

i can’t even get past the take the screws out part. 😂 there is no way. they are so tightly on there even a drill does nothing.

[@FitnessTechnologyServices]

I just had a viewer post they do use WD-40 on the screws and sometimes you have to use some type of vibration to loosen the screws tap war use an impact drill

[@g.lav80]

Would be nice to learn how to repair the control board

[@FitnessTechnologyServices]

There are a couple company’s on eBay but they run 199.00 + core too close to new for us .new we sell for 230.00

[@rmccorma]

Do these sole control boards crap out often? Ive only had mine for 6 months and it’s already needing a replacement... the wires started melting

[@FitnessTechnologyServices]

rmccorma well they are all the same or equal to others . The most often reason boards go bad is do to worn walk belt . If your wires are melting it’s most likely high amps from walk belt .see video amp check made easy hope this helps

[@rmccorma]

@@FitnessTechnologyServices It turned out the wire that goes to the switch was touching the board, thanks to your video I was able to install the new board and routed the wires so they arent touching the board...its been a few weeks of solid runs! Thank you for your video it saved me the time of having someone come in on the repair! Much appreciated!

[@FitnessTechnologyServices]

rmccorma awesome you should still check amps ? See video on amp check made easy Thanks Dave

[@rmccorma]

@@FitnessTechnologyServices thanks, will check it out

[@dg903]

This is fantastic, thank you! I have a defective F85 making this noise: kzbin.info/www/bejne/mX3IoYWwbMeqlbM Sole replaced the motor 2 times but neither fixed it. They sent a new board which is about to go in. Curious if you've seen this issue? Again, thanks for the video!!!