Restoration old rusty gasoline ChainSaw | Restoring 2-Stroke Petrol Chain Saw

Restoration old rusty gasoline ChainSaw | Restoring 2-Stroke Petrol Chain Saw
_ Currently, we are building a channel to meet the increasing needs of viewers. so our channel will focus on building more engaging and entertaining video content.
_ I hope this is the perfect restoration video for you.
_I hope you find something useful and enjoy this movie! I am pleased with your feedback, advice and suggestions for improvement. !!! sorry for the mistake if i made this restoration !!! thank you very much
follow me:www.youtube.co....
#Restoration2R #waterheatter #chainsaw

[@brianschott8162]

Ain't nothing like being out in the wilderness with your chef knife collecting roots and chainsaws...

[@user-ky5gf1cp2v]

ض..

[@douglasaraujo3252]

@@user-ky5gf1cp2v h

[@mrp-racing]

dude you mounted the piston the wrong way... The Arrow needs to point to the exhaust, not the intake

[@jasonhoose5215]

Did you see him pound the main bearing in for the center race... real cool lol

[@mrp-racing]

@@jasonhoose5215 Yea i did -.- , made another Comment about that

[@maxwelloregan8463]

I found the only people who know what theyre talking about in these comments. This resto made me cringe the whole time

[@mrp-racing]

@@maxwelloregan8463 Yeah there are a lot of stupid ones down there 😂

[@user-yj5vn1lz7h]

@@jasonhoose5215 🔪、

[@richardcrouse9074]

The cutting chain was installed backwards and re installed backwards. Also you must mix gas with oil for two stroke engines

[@leonsofficialvlog3693]

Nice good job idol tamsak thanks for aharing this video

[@user-iw5hz5qd6e]

Вот что вода и краска животворящая делает!!!

[@GTK31]

Muitos estão espantados com a memória deles, para lembrar onde vão as peças, quando montam. Só esquecem que eles estão GRAVANDO o passo a passo da desmontagem. Então é só fazer o inverso, quando for montar. E, claro, eles podem ter uma boa memória, também. Mas certamente a gravação ajuda bastante. De qualquer forma, é um belo e inspirador trabalho. Parabéns!

[@rickibudiardjo7935]

Ngomong naon sih

[@lommeron271]

I think the piston was installed the wrong side, the arrow is always on the exhaust side🤷‍♂️

[@eisbeinGermany]

Well it started

[@beingsneaky]

I noticed that too..

[@kosti116]

Hehe and more like no masking tape etc ;p

[@bjrneskimoandersen4895]

kosti116 honkez

[@codyflowers9804]

But the ring gaps never are....

[@emansyarifsomantri2351]

Bisaan si akang ieu.. Hebat kang lah, Ciamis hadir menyimak.....

[@valdis7663]

Просто супер, с удовольствием посмотрел на кропотливый труд. Молодец парень, руки золотые. Из инструментов шестигранник, отвёртка и разводной ключ, но это не помешало восстановить бензопилу.

[@user-td8vf7mr9f]

Он Русский, привык к УАЗикам, здесь всё тоже самое, отвёртка, симпатии, ну и благословение коей-то матери!

[@user-tc5oy3re7w]

Как там оказалась эта пила : ,,пошел лесоруб в лес и начал пилить деревья своей мощной пилой , но тут вышли гномы , дали люлей лесорубу и утащили в свое логово , а пила так и осталась:) Кто понял о чём тот молодец

[@user-fs1lu3eh8n]

Я в теме😂😂😂

[@hasanthasasika3685]

kzbin.info/www/bejne/mHWng59no7B5gM0 Water Pump Restoration

[@mrp-racing]

24:35 DONT HIT THE INNER RING! it will damage the bearing! Always Press or Hammer the ring that gets friction, like in this case the outer...

[@petri1654]

Same got to my mind, the first thing taught in bearing installations :) Hardly take damage with low pressure but next time hit the outer ring when installing bearing in the hole. When installing to the shaft hit the inner.

[@chadrswift]

That was my first thought. Every time I see a restoration, guys hammer in the bearing on the inner ring...

[@jasperprudon]

I did this 1 time and bamm bearings broken

[@samueltipple580]

First thing I did when I seen this. Is go to the comments to see if anyone else noticed

[@franzhelmke7939]

That was the first thing I saw, the thing with the inner ring and the bearing seat is painted that's not good

[@ss-ys1ix]

Молодец классная бензопила

[@Diy.at.home6385]

День добрый, при сборке вы неправильно поставили поршень,(стрелочкой к карбюратору,) а нужно стрелкой на выхлоп,

[@x84pav84x]

А в чём разница и какие последствия?

[@lyadovihifazenda]

@@x84pav84x Окна и кольца .

[@user-pw8nn5sj7t]

@@x84pav84x место стыка кольца попадает на выхлопное окно, кольцо ломается и последствия печальные!

[@Assinizaring48]

@@lyadovihifazenda заводиться будет но работать нет, это как бежать задом.

[@user-nz4wl1oe3q]

Там стрелкой к карбюратору и стоит

[@iikhaikal9829]

Siapa yg dari indonesia like

[@BondWarrior]

You NEVER insert bearing by hitting on the inner face, tap it in on the outer face , you damage the bearing by hitting the inner face

[@user-vj1io7ly7y]

Not at all, small bearing can be easily fitted in to the shaft of bearing housing. Heating producers can be done with big and critical equipment.

[@kevingoodrich5472]

Not only don't you use the inner ring but I'm pretty sure you should pack them with grease. My theory on this channel and about 20 others just like it, is that it's a rigged. Someone has set up a bot system and pays these people a few bucks to sorta refurbish different items and then they collect any KZbin money. I found a channel that was 3 months old had 5 videos and like ten thousand subs but each video had over 10 million views each. There are some where you can hear in the background someone wrenching on another project. Easy money just find a item that works sorta,trash it out some more and then pay a person 5 bucks or whatever to "restore" it and some else 5 bucks to film it. Then have 5 or 6 channels,edit the vids and upload and then turn the auto system on to constantly replay the vids, like printing money

[@austinhartley2312]

Yes!!! I saw that and got a little worried 🤣

[@mikeyd5969]

That and the piston is facing the wrong direction. Arrow towards muffler.

[@adrianleo1]

Reeve i agree, and with a peace of wood or with a plastic hammer.

[@BakoelGendoel]

Excellent upload. Full watched and have a wonderful day

[@JustAPersonWhoComments]

No annoying intro, beautiful shots, masterful work, extreme details.

[@thebarexam614]

Your screen name is 🔥

[@user-mo5fw8et2u]

@@thebarexam614 в

[@Toyota-ci3nj]

Wouldn’t say masterful work but thrust is true

[@thedolphin5428]

Bullshit bullshit bullshit. 1. Noone "just finds a chainsaw" sitting on a cut tree like that. Did the previous owner not think enough of his saw to even take it home after work ... or even to fix it if it stopped working. How lucky, just to find it as a friend was filming you. 2. All these "old machines" he "fixes" are dirtied up to look worse than they are. Plastic does not rust. Alloy does not rust like that. Any chainsaw motor and blade would be covered in oil and sticky shavings.

[@MARKK300691]

When they found it chain on backwards.. when he puts it back together he does the same thing... Then it shows when he is adding fuel the chain is on correctly... Got to love it

[@skullcandy2164]

mmmmm no bar oil either so much FRICTION!! lol

[@lorenzoviola7839]

the arrow on the piston indicates it must face the exhaust

[@hasanthasasika3685]

kzbin.info/www/bejne/mHWng59no7B5gM0 Water Pump Restoration

[@WorkshopMedia]

I have don a detailed restoration video in my youtube channel "Workshop media"

[@cjarjayofficial48]

Wow NiCe 👍👍 thank you for sharing 👏👏👏

[@NKVDLeningrad]

Подшипник запрессовывают по внешней обойме!!!

[@asak6943]

Мне иногда кажется, что они специально закапывают что то на некоторое время чтоб потом снять об этом видео🤔

[@Атомный_Дед]

Ну, вы же новости смотрите по телевизору? Там то же самое!

[@LDimon84]

Именно. Неужели кто то такую пилу выкинет в лесу

[@user-mw9oi1gy5b]

так и есть

[@theroadismaylife7117]

Я так и думал,всё вызывайте ФСБ

[@user-sx3kn9iz5j]

У него таких закладок по лесу ещё не на один год хватит. Но скорей у себя на територии зарывает потом просто подкидывает куда-нибудь

[@getfitwithtimo]

Cleaning all those parts is not for the faint hearted.

[@dhimaskhabib2981]

2019

[@bieyheroslr3]

Tiap2 kali jalan.mesti jmpa brg..ahahaha..lakonan kena mantap

[@danielvitolo2595]

So what happened? Someone cut a tree 100 years ago and oops, forgot their chainsaw.

[@Mjolnirmeister]

Love watching these restoration videos. even if, as all the comment say, they aren’t done 100% correctly. It’s just so satisfying seeing something be reborn.

[@jorgetroncoso5821]

Remi

[@kartaldogan9705]

Oji

[@bernardosousa870]

A hug A

[@bernardosousa870]

Bernardo sousa

[@aurealavez6108]

​@@jorgetroncoso5821 hhh7hhh

[@Wanous-hv7zo]

You have to run mixed gas in the saw. Looks like your putting regular gas in it

[@bualchhuakremruata3730]

Eedggee5tr

[@TF856]

Wouldn't it be interesting to leave something like that looking as grungy as possible but making it run?

[@joshuagargalione378]

Backwards piston, no bar oil, dull chain, no oil fuel mix,

[@Njazmo]

Chain backwards, silicone with head gasket, banging bearings with hammer, must be awesome.

[@jimk9701]

backward chain too..this guy typical asian..has no clue..watched one guy here restore a guitar..found it lying in the long grass..put it back together back to front...

[@georgejackson832]

joshua Gargalione how about praising the lad instead of knocking hi so what if he made a few mistakes IMO he did a hell of a job

[@Groove1024]

bent crankshaft, paint inside the engine..... that thing was poop now it's poop with wasted paint and bearing and it will last a week before have a real engine crash locked solid worst than if it was found under the sea after 10 years....

[@abhishekprasad8151]

how convenient that a chain saw was randomly laying around and he knew exactly where it was

[@austinledford8501]

Why does that matter? It was about the restoration

[@xiomaragomez8588]

@@austinledford8501 @@@

[@uhtred7860]

@@austinledford8501 Because the videos are fake.

[@austinledford8501]

@@uhtred7860 the builds are fake?

[@uhtred7860]

@@austinledford8501 No, he disassembles then assembles the stuff, that much is clearly true. What is fake is the "finding random stuff in the forrest when i go for a walk" and the condition of the stuff he "restores" He clearly paints or dips the things in some sort of solution to create a impression of rust or age. Maybe even some reverse editing. pay attention to the "rusty" components before and after, no pitting from rust at all, also the rust/ageing is always the same colour, and comes off very easily. But check out the xbox resto, or some of his other electronic restorations, they are the most clearly faked.

[@brucecox5884]

very good, what impresses me most of these type videos,is the remembering where all the parts go during the rebuild.

[@cdknight3625]

One can always look back at what has already been recorded!

[@MrSmity]

Cool another buried in the backyard for a week resto video

[@kunangchannel5767]

Wah sungguh sangat luar biasa, dari rongsokan alias barang bekas jadi seperti semula ... 👍👍👍

[@HighMaintenancePS]

Mistakes include but not limited to; -Painting inside the bearing and mating surfaces. -Incorrect paint for inside of engine. -Excessive gasket sealer will overflow into crank. Not optimal. -Bearings installed incorrectly in a manner that often causes failure. -Piston installed backwards, will result in failure. -Suspected bent crank, will result in failure. -Possibly incorrect fuel, will result in failure. -Chain blunt Well below operable standard.

[@Filip_Bubanja]

Yep, I noticed that too. But the worst thing he did is the way he istaled bearings 😱 The bearing nests shold be heated up to ~120 °c and then you put the cold bearings inside. They get inside like a dream and without any hammer.

[@randallreed9710]

So what? He found the fuckin saw in the woods. He'll get some use out of it for a while, FOR FREE! There's always some expert asshole critic. I guess maybe he should have called you where you could charge him to rebuild it, Fuckin cheap skate!

[@billschipper1718]

It wasn't free he bought a few parts and he put in his time. . I think he'll get five to seven years of use out of it. Well worth his time.

[@Filip_Bubanja]

@@randallreed9710 I totaly agree with you dude...there always has been expert assholes and stupid assholes, you decide which one you will bee 😂

[@calingabriela5413]

Lĺĺl

[@jamesh4966]

1 hr to dissemble and 2 months to clean. Excellent job.

[@perryellisonjr9303]

Piston backwards ,no pre oiling of and bearings,no oil on piston or jug to prevent dry start,some people are just born lucky

[@augustusshook2881]

Great Job Thank You for the video...

[@rmcseveney]

Did anyone else notice that the chain was on backwards when he first got it

[@LPJMagicmusic]

One of the first things I noticed haha That's probably why they left it out there 🤣 I did that when I was a kid and got so frustrated because it wasn't cutting and just burned the wood lol my dad laughed and made me figure it out

[@LPJMagicmusic]

@@stillwater62 cheated and turned it around? Lol that or figured it out and turned it around. Not sure why it would be cheating

[@elijahsjogren6267]

First thing I saw

[@elijahsjogren6267]

@Sean Tyree I'm surprised it took this long for someone to notice

[@LPJMagicmusic]

@@stillwater62 this isn't a tutorial bud it's a restoration. I'd be willing to bet over 90% of viewers on this video will never run a chainsaw. If this was a how to then I'd agree with you but it's not. If your learning about how yo put on a chain in this video of tell you that your not using the internet efficiently.

[@revamp777]

Just happened to be sitting there , another find!

[@ciceropedrosa9152]

Bom maçanico esse é o que se chama de proficional parabéns

[@benmazzone2650]

Lol at least they have a storyline behind their restorations

[@walterholzer939]

I find ChainSaws every day in the woods

[@LeatherFaceEditzzzz]

Me too bro

[@user-bm6bv4gb9d]

Ага вот так просто шёл шёл бензопилу нашёл. Хорошая сказочка со счастливым концом...

[@user-wk6ud5ul7x]

Мне показалось или он поршень неправильно поставил вроде стрелка должна на выхлоп смотреть а там на впуск?

[@saymon6327]

полностью согласен)))

[@aimansahaja5981]

I love how you smack that main bearing right in the center

[@handikarahayu4789]

😁

[@muhammadahsan5444]

@@handikarahayu4789 !

[@Groove1024]

yup and paint inside the engine and bent crankshaft and whatever.... it work (will last a week)

[@thomasturner1682]

The last 2 of these rebuilds the chain were on backwards before the start. Maybe that is why they were discarded.

[@albertocubilla6242]

Una pregunta tú no conoces el límite ere muy grande exitos en tu vida gracias mi reperto y admiración

[@user-xf5ls5vp4p]

Ходил давеча по лесу клещей собирал, глядь кузов от ламборгини! Подобрал восстановил, теперь все девчата на селе со мной здороваются когда я проезжаю.

[@hasanthasasika3685]

kzbin.info/www/bejne/mHWng59no7B5gM0 Water Pump Restoration

[@asderge]

Так чисто случайно нашел. Пила даже в землю невросла:)

[@Sgr-B2]

@@asderge они её месяц поливали солёной водой.

[@georggreek]

Фигня!Я титаник на ставке нашел,ото да!

[@---mn1fv]

Это все фигня. Иду я как - то по лесу, в форме лесника, вижу мужики дрова пилят. Я к ним ближе подхожу, а они бежать от меня. Так теперь у меня две пилы хускварна 365 и штиль 180

[@davesnedden8135]

should have pressed the main bearings in by the outer race , not the inner !

[@stevesting8701]

l thought that too bro

[@Groove1024]

yep exactly and should have replaced the bent crankshaft and should have not paint the inside of the engine and should have put it on the dumpster.....

[@brodytonelotti3577]

He put the piston on backwards too. Arrow on top should point towards the exhaust, not the intake. That saw won’t last long at all.

[@Jv19979]

@@brodytonelotti3577 he will learn

[@ziptiesandelectricaltape523]

And he should of heated the case in a oven or use a heat gun

[@user-tw6rh8bx3i]

Поршень установлен не правильно !!! Для особо "одаренных" на нем стоит " стрелка"!!! Так вот, стрелкой вперед, к глушителю, а не назад, к карбюратору !!! Горе-механик :-):-):-)

[@Alex_410]

Тоже от Белгорода сюда?

[@basudebghosh3036]

খুব সুন্দর একটা কাজের জিনিস জানতে পারলাম

[@JamesCouch777]

Always drive on the outer race of a bearing when installing in a housing, inner race when installing on a shaft.

[@wesleyrobbins9183]

I’m surprised he didn’t break one of the bearings wouldn’t matter any way because he gonna have to rebuild it agian

[@okgoogle80]

Классно получилось, кому тоже нравится ставь лайк👍

[@barmaleibarmaleev8599]

Хуяйк👎

[@user-fk8ko2xg9o]

Ну да в магазине взять замарать а потом разобрать и собрать ну гений просто пищей хуяйк а не лайк

[@kevinmcleod3741]

Did you notice the chain was on backwards lol! That's why it was probably left there ,,🤣

[@mitchelltollefson4376]

yea i agree

[@nicevoice8890]

kzbin.info/www/bejne/mWbPn6CFptaZkMk

[@sokhiobreeng7361]

Very good installation thank you

[@steakems995]

Yea that jug gasket is gonna last real long with a painted surface under the gasket 👍🏻

[@tggraham3321]

Pretty sure he can fix it

[@number7oneone]

@@tggraham3321 by looking at the video, probably not.

[@MrMuzzEdit]

Ооооо! Какое разнообразие! Он оказывается не только на берегу и на свалках что-то находит! Завидую. Вот у них бензопилы валяются. А у нас только бутылки, сапоги и унитазы. (((( Нет. Вру. Намедни собирал грибы. В получасе ходьбы по лесу от ближайшей дороги обнаружились: стальная эмалированная раковина, эмалированная миска и полусгнившая банка из-под советского паркетного лака. Это ли не странно? ;)

[@user-op1nk9gv1y]

Занимаюсь ремонтом бензо инструмента, но в 1 вижу что все без фиксаций, 2 крутить надо крест накрест, 3 поршень стрелкой к глушителю, а 4 ни разу не видал чтоб картер и целиндр красили. В 5 как он при разборки маховик откритил, не стапарив поршень. Зажигание не выставил.

[@user-nf3qv3no8b]

Ещё надо цепь наточить и крышку на шыну поставить, индейцы блин😀

[@petersburgsummerresident2311]

Смотрю как комиксы.. Только поржать... И откуда в лесу ну вот как специально валялась!!))))) ну и сам процесс без смеха невозможно смотреть)))

[@user-xu9qg8fi1s]

это видео надо смотреть с зада на перёд , тогда всё встанет на свои места

[@user-gg8pq6lv7k]

Да говно товар однозначно, уххаха

[@user-ok1vq9em3f]

Похоже женьшеня накопал . Конечно, под настойку из женьшеня хоть что можно реанимировать. Надо ему антикитерский механизм отдать, может и его запустит 😀

[@mariadefatimabonadiodossan6846]

Aquela introdução do vídeo sobre como encontram a peça acho dispensável, não dá pra acreditar!

[@lexholod2828]

1:29 Краской намазали (акварелью), поваляли в грязи... Пом типа нашли, отмыли, части какие то заменили и рабочая пила!!!... Так и я смогу, возьму и отмою свой "Калибр" от пыли и древесных опилок и пила как новая!!!

[@hasanthasasika3685]

kzbin.info/www/bejne/mHWng59no7B5gM0 Water Pump Restoration

[@BlankBrain]

1:28 No wonder someone left the saw in the woods. The chain was on backwards!

[@nicevoice8890]

kzbin.info/www/bejne/mWbPn6CFptaZkMk

[@ronmurphy1123]

That's how I acquire all my saws, just a walk through the woods and oh look an old chainsaw😁. Nice restoration though .

[@zex019]

The piston was installed incorrectly, the arrow on the piston is always towards the exhaust side...

[@deffocrap73]

i saw that to

[@buntatanis9572]

yes..👍👍👍

[@m.o.f9802]

1)Dont paint Sealsides 2)Dont hit the bearing at the inner Ring 3) Piston is turned around, arrow shows always exhaust side 4) be more carefull with the engine, dont throw that cylinder around, and dont let all the parts fall on them

[@nicevoice8890]

6kzbin.info/www/bejne/mWbPn6CFptaZkMk

[@randomidiot6281]

I bet you this dude is from China so what would you expect

[@RRDfinland]

3) if he knew that and put piston turned around to get better conrod angle 😁 but this only works 4t engines it rattles cold but no warm anymore

[@danieledwards1081]

Looks just like the cheap Chinese saw I've got in my shed...

[@hasanthasasika3685]

kzbin.info/www/bejne/mHWng59no7B5gM0 Water Pump Restoration

[@hasanthasasika3685]

kzbin.info/www/bejne/mHWng59no7B5gM0 Water Pump Restoration

[@TacticalTerry]

Awesome guess! I took details from your guess and the video and did a web search. This saw is likely a Chinese GR-4500 made by Zhejiang Jiauri Machinery Co., Ltd. (Found the chainsaw details and picture on Alibaba).

[@danieledwards1081]

@@TacticalTerry the one I have is from an Ebay seller, labelled as a Giantz

[@TickenLifters]

@@danieledwards1081 hes trolling you hes from the goe phuc urselph club

[@user-wo9cy7ck3g]

Типа нашли пилу ,все это не случайно ,заранее придумано , а за работу 5+

[@richardholmes9295]

You must put it together with oil on the seals, bearings and piston. Will not last long on start up.

[@colinjoudrey5953]

I was literally just thinking the same thing “bro you need those, there dust covers”

[@mikkelsrensen8282]

And The piston is turn The wrong way🤣🤣

[@vitoraugusto1573]

Quem aí tb está viciado nesses vídeos de restauração

[@henriquerubert570]

2

[@user-sl3mn8dh6q]

Постановка это понятно, но поршень при сборке не правильно поставил, стрелка должна указывать на выход газов(глушитель)

[@user-gx3qf9lt3t]

Я тоже заметил

[@abdalhafezkanaan1775]

انك انسان مبدع وصبور وفنان في تجميعه لا تقل مهاره عن الصانع

[@Magdusia2003]

bearings must be completly unsealed (lips of the sealing ring are oiled by gas mixture) and installed by outer ring , gasket is out of sense because it causes a gap in front of the engine body and its tension, silicone is enough, use some grese when intalling needle bearing

[@ziptiesandelectricaltape523]

Its fake water doesn't just end up in the oil tank without a huge ass hole in it.

[@davidschofl3908]

Piston instaled wrong . The arrow should Show to the exhaust not the intake

[@GGigabiteM]

Maybe he'll get lucky and the piston ring won't snap lol.

[@romainberger]

Do we talk about lubricating the chamber while putting the piston in....?

[@saveriamusso1963]

@@romainberger k

[@drgnhilord6900]

Rebuilds the whole chainsaw then checks for spark.. 🤣🤣🤣🤣🤣🤣🤣🤣. This was so staged Hollywood couldn't of done a better job.

[@andreasroth108]

Why do the rubbers look like new when the saw is supposed to be old? You don't paint the inside of a motor or hit the inner ring of the ball bearing. This restoration is a fake.

[@saknk1]

Agree 100%

[@bow0540]

That moment when he likes the comment

[@nicevoice8890]

kzbin.info/www/bejne/mWbPn6CFptaZkMk

[@Evgen_angler]

Не далёкие типы поставили цепь задом на перёд , попробовали не режет и выкинули её))))

[@user-co3wg2tc8j]

Я тоже заметил)

[@zedzedikus9877]

Да и бензин обычный заливают

[@user-vo4sn9ey8o]

Я тоже это заметил

[@andreytomsk70]

да это он её и ставил 38-12. Смотри, покупается пила на местном "авито", снимается кино как он её отдриставрировал. пилка закидывется на месяцок в сырой подвал и снимается новая часть дриставрации, потом монтаж этого высера.

[@user-gf3lo9zy2i]

Они ещё и поршень при сборке задом наперед воткнули.Замки поршневых колец могут попасть на окно в цилиндре,и сломаться.Стрелка на поршне должна смотреть в сторону выхлопного окна.

[@yeaheverday]

My man starting chainsaws with one flip flop on and y’all hating ? Pfff excellent work ! Enjoyed this restore, thanks 🤙🥃

[@〆XISHNIK个]

99

[@user-gt7jd3vc7n]

@@〆XISHNIK个 ㅃ

[@taumbannon5289]

Piston went in backwards. Aero points to exhaust. But very nice job.

[@user-bd3dt2yy9j]

騾 鑼 邏‼️ 腹蠡 ら らえり

[@Dylan-tj2si]

Also he damaged the bearing by hitting it on the inner circle

[@quyetdbui3110]

@@user-bd3dt2yy9j nó cứ sự

[@timeis247]

Next time you pound in a bearing with a socket, make sure the socket is big enough to cover the outer ring, not the inner.

[@buddyboy6337]

The chain was on back wards thats why they left it there.Would not cut lol

[@zemariaramos8380]

Nu

[@zemariaramos8380]

Nu L n lp

[@zemariaramos8380]

Nula o Que bLGXT NLG km

[@zemariaramos8380]

J

[@WrathOfMrRodgers]

Omg you are right.. maybe they were high put it on backwards and put it down and got lost in the woods and died.. that poor dumb soul

[@garymucher9590]

Never knew they made chainsaws that didn't need an oil mixture for the fuel to work. Won't be long for that chainsaw to have no compression and seize up.

[@peterfedor9288]

I'd like to know, how u figured out that he used fuel without oil.

[@jamesburton5139]

@@peterfedor9288 you clearly have no experience with two stroke fuel mixture. You can tell just by looking at it when he poured it in.

[@tigerxra8515]

@@peterfedor9288 Well, based on my little experience with 2 stroke engines, the oil is in quite dark red colour (Like a blood from vein). So it dyes the fuel in red - reddish colour.

[@peterfedor9288]

@@tigerxra8515 There are various brands of the m2t oil - red, green, blue, yellow and so on. U can't tell by looking at gas if it's mixed or not with yellow oil(that's why I don't like these oils - can't see the difference). I have workshop and do engine repairs(fyi james), so I know what's going on.

[@tigerxra8515]

@@peterfedor9288 Oh, thanks! I had my suspicions that there is more that one colour of oil, but I wasn't sure. Yeah, I love the red oil. It's easy to tell if fuel is with oil or without. Is there are difference between the oils, apart the colours?

[@surotoprastyo278]

Paling suka.cannel ttg restorasi....mantab...

[@user-zr2og7zf9k]

ГЛ4500.Уменя такая уже лет 10 ток глушак другой.👍

[@Celinor33]

This guy can disassemble the world with an Allen wrench

[@egoriliin1485]

за такую реставрацию руки оборвать, поршень наоборот поставил, шпильки без резьбы не поменял, подшипник кто так заколачивает?

[@1Andrei75]

ПОРАБОТАЕТ НО НЕ ДОЛГО;)))

[@user-ox4sw8gg8z]

Впарит кому нибудь , но видос классный🙂

[@tadeusz4306]

super-to prawie tak jakby znalezc stara prezerwatywe i pokazac dziecko !!!

[@hefeus1]

Nice effort but you drive a bearing in on the outer race. When you strike the inner race, you ruin the bearing. That will run for a couple hours before it grenades itself there ace. Nice overall effort but pay attention to the details.

[@francisconascimento9102]

Vc é o melhor. Como essa motocerra tava feia e depois de restaurada ficou linda vc é o cara. Um vidio desse só bobo mesmo pra não da um jóia. Valeu irmão fica com deus tmj.

[@kauantadeu3809]

A minha motosserra ninguém consegue ligar já coloquei gasolina nada kkkkkk

[@craigpalmer5693]

Rusty chainsaw he going to take it apart clean up restore everything like new again you are the best fixing equipment abandoned bless you

[@zainijantan9347]

Mantap, buat kerja yang rajin.

[@kir5775]

Подшипник впрессовывать ударами по внутренней обойме ??????? Расходимся .... все ясно

[@AlexxxxBY]

Ещё на стадии покраски картера со всеми прилегающими поверхностями и внутри + покраска цилиндра, стало всё понятно. А если глубже копнуть он вообще не понимает в пилах, покрасил шпильки крепления шины, а их вобще поменять надо на них нет резьбы, как зажимал сцепление не показано, поршень поставил наоборот, катушку прикрутил без выставления зазора, поршень судя по всему наждачкой пошкрябал весь. Запуск вобще угар, у пилы лёгкий старт есть, нужно просто за шнур тянуть, а он дёргает как припадошный. Крышку сцепления с тормозом можно было докупить она на китайки копейки стоит, ну судя по всему он понятия не имеет, что там крышка должна быть, по его действиям пилу он первый раз в жизни видит.

[@MaRaX047]

31:07 I think the piston is not installed correctly...the arrow should point to the exhaust.

[@iirovannas3908]

I think the same

[@garyrowe58]

There was a lot of 'detail' left out of this - like all the tricky bits!

[@user-nd2cq3oe1v]

와우!!기술천재다.박사이상노벨상줘야....

[@mariegibareceitas8877]

Deixei nosso like somos do Brasil abraço

[@66roha]

Цепь не правильно стояла с самого начала,из-за этого и выкинули

[@user-gh3xg2yq2s]

Не говори,и смысл рестоврировать если все б.у,палец в поршень должен туго заходить,хоть и подшипники игольчатые,можно было хоть поршень поменять.

[@hyustonechanel8855]

Просто удивительно, что «старая» бензопила конструктивно идентична новым бензопилам китайского производства в пластиковом исполнении...

[@user-hf9gk1yk1b]

Потому что она не старая, и врядли была там на самом деле

[@hasanthasasika3685]

kzbin.info/www/bejne/mHWng59no7B5gM0 Water Pump Restoration

[@letutu1403]

@@user-hf9gk1yk1b ⁸l

[@user-um5bv7hk2k]

2

[@user-um5bv7hk2k]

Нас не будет

[@victorsierra8881]

Yo la desarmo,pero no recordaria como armarla la dejaria tirada.Me gusto el video muy entretenido, saludos desde uruguay

[@lizzielecates4430]

Very nice job... Tell me what did you soak the aluminum parts in to make them so shinny?

[@mbrent02]

I'm amazed also to the original person who assembled that ..

[@iraagans3144]

Your channel has no videos?

[@ohyeahgamer3736]

@@iraagans3144 so

[@iraagans3144]

@@ohyeahgamer3736 I just thought that it was odd that you filmed yourself assembling the chainsaw but didn't post it to your channel?

[@htownpony8449]

For those that don’t know…..those bearings were installed incorrectly…..bashing on the inside race damages the bearing, he should have used a bearing tool and a press on the outside race.

[@Sylvia501g]

Exactly

[@benwilkerson3762]

Or heated the case halves while chilling the bearings. They would’ve dropped in that way without need of a press.

[@shawnmartisko1966]

Awesome Restoration job

[@user-jo7tf6sk1x]

-спасибо !!буду знать как устроено !!!-снимал карбюратор на бензопиле!!!руки -отмывал две дня -а у парня (как жена сказала) ногти чистые !!!!как ?????!!!

[@LDimon84]

Бери пасту вьюрт, она с абразивом. Отлично все отмывает.