Revive Your Drone Batteries in Seconds - You Won't Believe How Easy It Is!

In this video, we'll show you how easy it is to revive your DJI batteries in seconds-using the CP2112 debugging board!
Part 2 watch here - • How to Revive Your DJI...
If your drone's batteries are no longer charging, this is the video for you! We'll show you how to quickly and easily revive your batteries using the CP2112 debugging board. After watching this video, you'll be able to revive your batteries in seconds-and you'll never believe how easy it is!
CP2112 Debugging Board - www.aliexpress.com/item/40010...
DJI Battery Software - forms.gle/M89x2SPkQGQfz7n77
Battery Adapter Boards - www.aliexpress.com/item/10050...

[@thegreatbigco]

Awesome video as always! Very helpful and informative! Thank you Dave. :)

[@timmorgan9963]

Does this procedure work with a Phantom Advanced and the Mavic Pro? If not can you advise what to do to revive these, in particular the Phantom batteries! Thanks

[@yashiro1800]

Helpful tips as always, thanks guys!

[@mathieuhenrissat1449]

Where we can buy the cable to connect the cards please ? Have you got a link ? Thks

[@djseedee444]

Very interresting Thank you . But Do you know if its working with tha avata battery ? Thank You

[@therealchayd]

Awesome video, thankyou 👍 Note: This can also be used for DJI Ronin gimbal batteries (I've revived a couple of packs for a Ronin-M) SDA, SCL and GND can be found as test pads on the BMS board, or from the outside with the connector block upwards and the connectors pointing toward you, the two largest ones, from left to right are + and - , followed by two recessed contact pads, top is SCL, bottom is SDA. These are based on the TI BQ30Z55 which you'll need to select in Battery Killer, otherwise you'll get errors. Update: Just used Battery Killer to revive a dead Ronin-S battery as well, what an amazing tool!

[@webuydronessa]

Thanks for the comment and info , good to know it works on the Ronin Batteries , thanks for watching

[@gokux.]

it will work with ronin mx batterys right ?

[@therealchayd]

Sorry I can't say either way, @@gokux. I only tested with Ronin M battery.

[@therealchayd]

@@gokux. Sorry just seen your comment, I don't know which ones the MX uses, but if it's the model No: 423496 (1580mAh 14.4V) then yes, this should work.

[@MasakyoRenSai]

Is there a similar method for the batteries used by DJI Osmo Gimbal with Zenmuse x3? The first model I think.

[@EliteDronesAZ]

How about something for the BS60 batteries for the M300? We have two that are dead... wont light up or take a charge. The batteries in question have only be charged and used one one flight ever.

[@InfinityDrones]

Awesome man!

[@rcguygarage]

I quick checked your videos, do you have a phantom 4 reset board for the bms

[@webuydronessa]

Thanks for watching , you would need to use a EV2300 for a Phantom 4 , check this video for that process kzbin.info/www/bejne/ZpLcg35njLmYjdk

[@aeroshootstudios]

this is so awesome and very cost effective, will definitely be looking at getting the little board just in case I need to use it. rather have it and not use it, then need it and not have it. as always awesome video, keep them coming.

[@webuydronessa]

Thanks for watching 🤙

[@Macgregor_images]

😢so untried just going at face value 🤔

[@michaelwagner3161]

Great video!

[@ramim.5856]

I did the reset battery using the software but still cannot charge the battery it's zero empty no charge at all so is it damaged or I miss somthing or need to reset with much power? I used the power from the usb only when reset! Thanks

[@FrenkMeesters]

I already have an arduino uno does this work with that board as well?

[@adrianpostell7581]

Is there a solution for the original mavic pro?

[@mmerekomoshomo5412]

These guys sold me used TB48 2 years ago, best service ever.... good guys these ones,

[@Viljoen]

Something similar to this for the P4P would be great

[@cameronmeehan6206]

Hey great video. I’m going to give it a go. I have the boards but just need to software if you can help me out? Also just need to clarify the pins as one board show (GND, SMBC, SMBD,VCC) and the other board (VCC, GND, SDA, SCL, WAK, INT, RST). Thanks

[@webuydronessa]

Hey. The link to the software is in the description. Unsure what you mean regarding the pins, the only pins needed are the GND ( Ground ), SMBC ( Clock ) and SMBD ( Data ). The "other" board would then use pins gnd, SCL ( clock ) and SDA ( Data ) accordingly. Let us know if you get stuck and we will gladly assist. Thanks

[@donovaneades5812]

Where do you get the link for DJI battery repair tool?

[@davidcox692]

Hi can you help please what do i need to sort out my mavic air batteries they are not charging , just took it out of storage and not charging can you help please

[@Av8orDave]

Wow, it worked. Not quite as easy as yours, but it worked. I could unlock everything with the software, but when I exited and pushed the button on the battey, a single light would light for a few seconds then turn off. Pushing again would not start any lights. I tried it several times. So I tried to upgrade the firmware. It didn't complete, but the battery then had 2 lights lit solid. It would not charge. The lights just stayed lit. The charging hub would still have a red LED on it. From someone else's youtube video, I saw that if I used the DJI Assistant, it would detect that i had mismatched firmware. I ran that, and it FIXED IT! It's charging now. My batteries probably only have a few hours of flight time each, so happy this saved one of them.

[@andreswanepoel3933]

Nice video, what debug board and software for mavic pro 1 and where available in south africa, thanks

[@webuydronessa]

Good Morning Andre , here is a video relating to Mavic Pro batteries kzbin.info/www/bejne/ZpLcg35njLmYjdk

[@armandavtyan4023]

This is probably a dumb question but how many wires and which connections I need to make between the battery adapter and the usb board? Thank you so much!!!

[@webuydronessa]

Hi. Please send an email with the questions you may have and we will do our best to help.

[@novkimsanmd1591]

It's very helpful for me, thanks 🙏

[@Av8orDave]

So I got the board, hooked it up. First got SMBus failure 0x00, so hooked the battery charger. Everything was successful - both unseal buttons, and both Clear PF buttons. But when I exited, the battery button still does not light up, and if I put it on the charging hub, I still get the red light. Any other ideas?

[@joelrggizmo1373]

Do you make adapters for other batteries such as rigid tools, Milwaukee, Makita . Ryobi, which has one of the worst battery problems of all times. Those things are always dying. I have the mini 3 dji mines pretty new it's only about a couple weeks old so my batteries are still in good condition. I never charge them until they're at the right point and I never took them off the charger until the batteries are complete. Yes, I have adjustable power supplies. If you don't have anything yet for power tools let me know. I would like to see something like that that would be very handy.

[@Krusty-]

I need this for the dji fpv drone battery, it is completely dead. Wont take charge nor turn on at all even when plugging it to the charger

[@John_2Much_Coffee]

Thank you for sharing, Cheers

[@webuydronessa]

Thanks for the visit

[@clintonwhite5850]

Thanks!

[@robbyhadinata3166]

hy.. i just bought the CP2112 ..but it comes separately with its steel connector ( Idk the name ) should i solder it first , or i can just use it rightaway ?

[@webuydronessa]

Hey. Yes, you would need to solder the pin connector to the CP board. Fairly straight forward if you can solder a bit. If you need assistance, please send an email and we can respond with the layout of the pins.

[@retrohipster1060]

I'm very excited to give this a go on my spark. I stopped using it for a long time, came back, and have 5 batteries that are dead. ^^; I'm about 99% sure it's due to an cell undervoltage situation. (I'm really familiar with BMS and lithium tech.) It's great to hear that there is an i2c bus connection on the battery connectors. I assumed I'd 100% have to use something like pogo pins or soldering on the board to clear it if the software existed..

[@webuydronessa]

Correct. Pin in and thats all, IF the cells are high enough for the BMS to be in an on state. If not, you would need to open the Spark battery and get the collective voltage up to at least 10.5v, then flag can be cleared. If its a cell undervolt trigger, and you are able to charge it back up and it balances and holds charge equally, thats a completely usable battery then. Thanks

[@garygembala306]

Hi Had to take my Mavic 2 battery apart because totally dead. To use a power supply, hook red to red and black to black - correct? And 12 Volts correct? Will that give the battery any charge?

[@webuydronessa]

Check the back of the battery, I believe the nominal voltage is 17,3V ÷ 4 cells is 4.3 volts per cell

[@peterh1911]

Awesome thanks for the video, will you guys be stocking and selling the CP2112 and the battery adapter boards in the near future?

[@webuydronessa]

Thanks for watching, it's definitely something we would consider doing if there is enough demand for them in S.A

[@LanceRazon]

When replacing cells of battery, will I need this method?

[@fredrombold479]

I have a Mavic Air and 2 dead batteries. I see the debugging board on your website, but is the adapter board also available? When buying these, do you make the software available?

[@webuydronessa]

We have stock of the board , but we unfortunately do not stock the adapter at all , you will just pin in the wires directly to the battery which is easy to do , and yes we supplier the board, the wiring and the software if you purchase a board from us.

[@angelvaca9232]

Is there any way to also know the battery chip? is for mavic 2 pro and the battery model is FB2, thank...

[@daconpictures]

I have a DJI TB-48 battery (2) that are not charging. Never used actually, just sat in the case for a long time. Have bought the DJI Inspire 1 V2 Black and never flown it.

[@neser07]

I bought it for my 3 Mavic Pro 1 battery, I haven't tried it yet, but watching some videos I see that they rule out the possibility of reviving these in particular. Could it be that it works with the batteries of this drone, what can you tell me?

[@webuydronessa]

The CP2112 won't work with Mavic Pro 1 batteries , take a look through our vidoes you will see we specifically did a video on Mavic Pro Battery recovery , it's a little more involved with different software and tools required.

[@AneeqaMeyer]

Great 🙌🏼!

[@carterbarcelo5844]

Hello have you tried this and does it work for you? If so can you link me the wire they used at 6:41? Thanks!

[@mickricksbsc]

I forgot to charge my Phantom 3 Pro batteries (DJI Originals) last year before storting for the winter. I just took my P3 out to check around our property for wasp nests, and both batteries are dead and won't take a charge. Is there any way to revive them? I really don't want to spend upwards of £200 for two new batteries if it can be helped.

[@marthacintron3578]

I tried to buy one from your site, but you don't have them. How can I make the adapter board myself?

[@Mats-hr5tl]

Hi, can you also use a arduino uno instead of the CP board?

[@webuydronessa]

Hi. Yes you can, but requires a lot more fiddling etc, due to Arduino's extensive programming capabilities. The above is not just cheaper, but MUCH easier and faster. Thanks

[@moonrunner3050]

Hi there , can you help ? Zero vega, ascend and cirrus batteries look the same are they interchangeable ?

[@webuydronessa]

Unfortunately not

[@calvinplb]

chance upon ur video. can share the link to buy the hardware and software to revive my Mavic Air battery ?

[@webuydronessa]

Hi. Did you manage to get the hardware and software as per links in the description? Thanks

[@jamesjay1987]

a lot of people getting problem with xiaomi fimi x8 se drone batteries and fimi does not help but making them to buy new battery. problem is: battery percentage gets sudden drop in the air like %40 to %0 and then bms flags the battery as "over-discharged". you cannot use the battery from that point. you can only charge it externally and see all cells are great. some people using these batteries with other drones and fly 20-25 minutes without problem but fimi x8 drone does not accept it because its over-discharged flagged. so we need to solve this problem somewhow like in this video. any thoughts?

[@greganwhittal]

Awesome

[@ExploreNewZealand]

Thanks

[@cooljazzhd]

Is the battery for a Mavic Air 2S the same as the Air 2? If yes, I'm assuming the board will work for the Air 2S, correct?

[@webuydronessa]

Yes they exactly the same 👍

[@meekomouse]

You need links for the darters to go from the debugging boar to the adapter

[@webuydronessa]

Hi, not sure what you mean exactly.

[@spike4790]

Hey guys, love the video. I was wondering do you guys have anything about reviving a Anafi USA. As I dontvrelly feel like spending another £288 for another batter if I can avoid it.

[@AshrafRogers]

Unfortunately not. We only focus on DJI sadly

[@shabs215]

Neat vid once again

[@webuydronessa]

Glad you enjoyed

[@gledalessio7784]

Good evening, could you send the pinout diagram to connect the CP2112 board to the DJI Air 2 battery?"

[@webuydronessa]

The pin out diagram is in the software , if you click "help" and select the battery in the options you will find the diagram, hope that helps.

[@nic8850]

Do you guys still sell the cp board, battery board, and software still for a spark? And ship to US?

[@webuydronessa]

Yes we do , unfortunately we do not export at all.

[@carterbarcelo5844]

Hello do you sell all this stuff on your website? I would buy it. Please let me know, thanks!

[@ejferarri2874]

Is the board also compatible with Air 2 S , also do you not stock it for sale to public as the 30-60 days delivery is just soooo long

[@webuydronessa]

We are condering stocking them at the moment

[@AshrafRogers]

In Stock Now

[@jordanhess2061]

Is there one for Phantom 3 ? I have 4 batteries that sat for a couple years and now they won't charge. Anyone know what problem is or how I can fix this ?

[@PhantomRider-78]

Does this help for mavic 2 swollen batteries? Only have 27cycles on the battery and noticed it started to swell

[@webuydronessa]

It does yes , but we would not recommend trying to revive swollen batteries , the risk of additional swelling in flight is 100% possible, it will result in the battery popping out during flight and the drone will crash 😳

[@dronerossantander2131]

hello, this card is also used to revive phantom 4 batteries?

[@webuydronessa]

Unfortunately not , we made another video showing the tools required for Phantom 4 & Mavic Pro

[@gregdonnelly6181]

great video, easily the best I have seen on this subject. I've bought all the parts you recommended but am struggling to find the DJI Batter Killer software. Can't find how to email to ask you to send me as you kindly off in the video?

[@webuydronessa]

For International views who require the software, please leave a small donation even if it's one dollar, once donated email us at [e-mail] for the password. DJI Battery Software - forms.gle/M89x2SPkQGQfz7n77 Thank you for watching, please consider subscribing it really helps the channel out.

[@bimblum1]

Do you have a fix for Phantom 3 standard batteries. They were working when I put them away but that was 2 years ago. Now one has 1 light then goes out and 2 others no lights at all.

[@webuydronessa]

Unfortunately not , there is no software support for Phantom 2 or 3 batteries

[@adamb1671]

I have the same issue as yours for P3 Pro 4k.. Any luck ? Have tried 'jumpstarting' mine to bring the voltage up but still not charging ☹️

[@737smartin]

video title: "Revive Your Drone Batteries in Seconds - You Won't Believe How Easy It Is!" Couldn't be further from the truth!😢😢

[@Tore_Lund]

You think that is hard? Luckily, you don't have a handheld gimbal. there you have to take the battery pack apart and solder on the data wires.

[@stevrgrs]

Clickbait as is 98% of videos on KZbin :(

[@Bwong55]

Or your just a dumbass​@@stevrgrs

[@diy-not5514]

Will this work with the original Mavic Air batteries? 2 out of my 3 batteries won't charge anymore they don't wan't to come out of hybernation

[@webuydronessa]

Yes it absolutely will

[@JGreg808schannel-dj1oq]

This is a great tutorial. Where do I purchase the boards and get the software?

[@webuydronessa]

Pop us an email on [e-mail] and I'll send it to you , the CP2112 board can be bought on Aliexpress

[@chopper8511]

Can I get the software please. I already emailed a request for it

[@manuelzelaya9810]

Do you have a complete kit like you showing on minutes 8:59 my batteries is for Mavic 2 like in video???

[@webuydronessa]

Yes we do just not the battery adapter boards

[@seanmallett2311]

Could you attach a link for the cables that you used to connect the battery board to the USB reader?

[@webuydronessa]

We used the adapter boards but they not needed at all , you can pin straight into the battery

[@maltly]

You can use just regular jumper cables, that are used for arduino and similar stuff

[@renocamilleri345]

Great video, ordered the CP2112 Debugging Board and the Battery Adapter Board from the links provided. I just need the DJI Battery Software. Would you be able to transfer me the files please?

[@SgtRic58]

There is a link provided above, and once the form has been completed, and you email them at the link in the instructions, they will send a link and the password.

[@maxun1]

Can this be use with the Mavik platinum pro battery?

[@webuydronessa]

No unfortunately not. Here is a video for Mavic Pro Battery repairs kzbin.info/www/bejne/ZpLcg35njLmYjdk

[@NishaanAhmed]

What does the reset PF and PF2 stand for? and can you clear the cycle count with this?

[@webuydronessa]

PF stands for "permanent failure " those errors can be removed and yes you are able to change the battery cycles if needed.

[@NishaanAhmed]

@@webuydronessa What button to press to reset the battery cycle?

[@webuydronessa]

Unsealed the battery , input cycle count as 0, 12 ,16 or whatever you want and then click cycle count

[@NishaanAhmed]

@@webuydronessa Thanks man. Can i get the software please?? 🥹❣️

[@GarretKrampe]

I got the adapter board for Mavic 2 and the VCC was not connected so I soldered a pin to the end of the power connectors. No amount of trying with 4 batteries that had ust been left in storage over covid could get the program to read information. Always a ERROR: Could not perform SMBus read 0x00 . Tried pushing the battery button. Can you ust hook up a power supply say of 2 V and limit to 1 Amp and put that on the battery pins ? and how are they connected in the battery ? is it from left to right or from outside in ? That way I might get some charge in it battery by battery. Aparrently you do not need to connect VCC ? OR should I hookup an lab supply to GND and VCC at 3V and try again as all the batteries read 0 volts.

[@GarretKrampe]

pulled top off the battery and the two accessible flat lugs from the battery read 3.6V what are they supposed to read do you know ? the next set down are 2.8 V

[@webuydronessa]

Hi. Did you manage to resolve above? Thanks

[@GarretKrampe]

@@webuydronessa No I have not yet. I think I'll make a pin hole in the case and charge each cell to 3.8V, then try the program and adapter again . Trouble is there is a lot of fake crap out there in Chip land so I could just have a fake chip.

[@88Henkie88]

will it work for the self heating variants that comes with the mavic 2 enterprise advanced series? i have 1 battery that is out of running thanks to forgetting to charge for a long time

[@AshrafRogers]

Yes it will

[@88Henkie88]

@@AshrafRogers great i only have to see where i can get the software because i can't find the right one i see in all the KZbin movies the one they use

[@webuydronessa]

All the details are in the description. We also have a few of the boards as above ( CP2112 ) left in stock. If your drone's batteries are no longer charging, this is the video for you! We'll show you how to quickly and easily revive your batteries using the CP2112 debugging board. After watching this video, you'll be able to revive your batteries in seconds-and you'll never believe how easy it is! CP2112 Debugging Board - www.aliexpress.com/item/40010... DJI Battery Software - forms.gle/M89x2SPkQGQfz7n77 Battery Adapter Boards - www.aliexpress.com/item/10050... We Buy Drones S.A

[@88Henkie88]

@@webuydronessa the cp2112 board i already bought but even the beginning of the page says considering an donation. its not an option to not choose because it not working. okay and i thought a small donation don't hurt but maybe its my country or the available payment options i own. but i don't see any supported payment option to make the donation.

[@alexandretirone4690]

Could you please let me know if it is possible to use the "TRB" software with the CP2112 communicator? Thanks

[@webuydronessa]

Hey. Unfortunately not. TRB only has support for the EV2300 and EV2400.

[@milosvajdic7467]

Hi, Are we able to use EV2400 HBA500 for phantom 4 batteries or EV2300 HBA002@@webuydronessa. EV2400 seems much cheaper

[@webuydronessa]

Hi. You will be able to use the EV 2400 ad 2300 yes, but not with battery killer unfortunately.

[@fire350]

Can someone tell me what wires go where from board to adapter? Thanks.

[@webuydronessa]

Hi. Please send an email and we can assist with your query.

[@philtw136]

IS there a debugging program for DJI on Apple mac ?

[@webuydronessa]

Not that we are aware off

[@brianfalconer9499]

Is there any way to revive a Mavic Pro battery. No LED showing at all?

[@webuydronessa]

Watch this video for Mavic Pro Batteries kzbin.info/www/bejne/ZpLcg35njLmYjdk

[@craftywoodworks551]

Interesting that the cp2112 board is only made for certain batteries, let’s say you wanted to do this with a phantom 3 battery, is it possible in anyway?

[@webuydronessa]

Not with the CP2112 Boards that we know of , the problem is always the supporting software required along with the hardware

[@craftywoodworks551]

@@webuydronessa I purchased the required hardware and will post results when I get them

[@sdynak]

@@craftywoodworks551 Any luck with the Phantom series? I have a 4 and looking to do the same.

[@jburic09032]

Can you provide link for connector you use in 6:38? The items purchased from AiExpress don’t include this adapter.

[@jburic09032]

@webuydronessa Can you help me with a link to this? It’s the only piece missing in my repair.

[@carterbarcelo5844]

Hey man please let me know as well if you find it. I’ll be looking and if I find it I’ll let you know

[@carterbarcelo5844]

I found it. Order off of Amazon it’s cheap. Dupont Wire 120pcs

[@gordanasutton3943]

Wow. This is great. Do you know where I can get the adapter for the mavic pro drone. Yay. Great video and made me feel happy again.

[@webuydronessa]

The Mavic Pro uses something completely different , watch this video kzbin.info/www/bejne/ZpLcg35njLmYjdk

[@antonioorfao9259]

Hi, mavic pro 1 battery can fix with this method?

[@webuydronessa]

No this won't work for Mavic Pro batteries we have another video on the channel for Mavic Pro batteries

[@kangaroo-nm5nn]

Hi, thank you for the video! I got the adapter as well as the board. However, whenever I run the software, I get an Error that it cannot connect. I have three batteries that are hibernating, but it even shows the message on my functional one. Any idea what it could be? Thank you!

[@kangaroo-nm5nn]

on a different Computer it gets recognized. However, I get stuck at the 0x00 Error.

[@AshrafRogers]

@@kangaroo-nm5nnhi. Have you managed yet? If not, pop us an email. Thanks

[@countrymouser1962]

I have a Mini-3 battery that is showing 2 lights, but will not charge. Do you have a debugging board for this DJI Battery? Thanks.

[@webuydronessa]

The Mini 3 is still a little new , i am sure there will be something soon

[@ua9851]

never update Dji mini 3 to latest firmware. Dji changed all the battery passwords so free software no longer works.

[@JoannaJedrzejczyksForehead]

Will this work for the 4 leds all flashing 3x, when trying to charge. I have this issue with a new, never flown, battery.

[@webuydronessa]

Hi. Which model of battery do you have?

[@JoannaJedrzejczyksForehead]

@@webuydronessa it’s a DJI mini 2. I was able to exchange it though.

[@jlyellphotovid9406]

Great video! Donated and sent and email requesting the battery killer software please.

[@stephenmason5682]

Is the Mavic Air 1 a Mavic Air? And the Mavic Air 2 the next one up?

[@webuydronessa]

Hi. That is correct yes

[@angelvaca9232]

I made the connection and connected its charger together and was able to restore one, but my other battery recognizes it and reset its parameters with the software but it still does not turn on its LEDs or charge, what could it be? is for mavic 2 pro and the battery model is FB2, thank...

[@CRUZROYHelicopters]

do a battery below 1000 mv and i would like to see you revive with this technique

[@webuydronessa]

Hi. We have managed to revive batteries that had 0 volts. These were fortunately in " hibernation ", so just giving it a little voltage kicked it out of 0 volts, and went straight up to the required voltage.

[@colinowen1]

Hi, just thought you might like to know that I was just connected to my battery with your software and the CP2112 board, unfortunately when I hit clear PF2 it instantly shutdown my pc and having rebooted I cant connect to the battery, it was looking so good to, what a shame..

[@webuydronessa]

That does not sound right at all , was everything connected correctly?

[@colinowen1]

@@webuydronessa yes well it had connected and done the unlock and first PF1 ok so I believe it was connected ok or would nt have done that..

[@JESSEPAVON]

How do i connect two to batters together to have double the flight?

[@JESSEPAVON]

For 2 se

[@ThreePilotsFPV]

I would like to recell a dji FPV battery. Can you give some info on/ if those will lock and how to. Kiwi4

[@webuydronessa]

Hi. We unfortunately have not done an FPV battery as of yet. Battery Killer does support the FPV battery though so if you have the cells, you are able to calibrate and change to the new cell capacity with Battery Killer.

[@bungabooboo]

what about mavic pro battery model number fbi-3830 mah -11.4?

[@webuydronessa]

Watch this video for Mavic Pro Batteries kzbin.info/www/bejne/ZpLcg35njLmYjdk

[@colinowen1]

Hi, Just thought id give a bit of an update, I purchased a second CP2112 board and again connected it, ran up the software connected ok, read out the parameters ok, unseal 1 ok, unseal 2 ok, Clear PF ok, clear PF2 and again that same electronic burning smell from the board and no more comms,.. very strange, I will try a different type of comms module if I can fine one and get back if it works..

[@webuydronessa]

Please email us for support and help, add some pictures if possible, email to [e-mail]

[@colinowen1]

@@webuydronessa Hi, thanks for the reply by the way, I have only just come back here.

[@AshrafRogers]

@@colinowen1Hi. Did you manage yet? Give us a shout via email 👍🏼

[@navleemedia]

Does anyone know how to diagnose a Dji Ronin M Battery Module 😥 I have a Dji Ronin M complete kit which was used twice only. Is there a bypass or a way I could use it with wired power ?

[@webuydronessa]

We have done a few Ronin batteries so yes it does work on them

[@jfjerez]

I purchased the interphase board, then when I click on the software, I found the problem that I needed a password to access the software, and in order to get the password I needed to donate, I have no problem and I clicked on mine link to do that but the donation site is closed and don’t allow me to donate. Now I going to receive the board and no software…the adapter there not on inventory but as you explained. That will not be an issue because I have the option to plug it direct to battery. Any recommendation?

[@osvaldorosado9065]

I donated and never got an email with a password

[@alanrobertson1238]

is there a software version for Mac OS???

[@webuydronessa]

We have not tried it on Mac , but i believe its for Windows only

[@carrieparent587]

I have a dji air 2s will this work for that

[@webuydronessa]

Yes it does

[@colinowen1]

The battery was from a dji mavic mini 1 in case you are interested.

[@KernowMan68]

Can this be used for the DJI Phantom 2 Drone Batteries?

[@webuydronessa]

Unfortunately not , there is no software support for Phantom 2 or 3 batteries

[@ua9851]

NLBA1 software supports Dji P2 and P3 batteries unlock

[@terrenceparker3119]

I have 4 mavic 2 pro batteries are u willing to charge my batteries for me if i send them to you ? If so how much would it cost me ?

[@webuydronessa]

Yes sure , we charge R600 per battery

[@Atomic_XGotQuestions-rh3vh]

Can this be done with the original Mavic pro battery?

[@webuydronessa]

Yes it can , that video coming soon as soon as we have a gap to film it

[@Atomic_XGotQuestions-rh3vh]

@@webuydronessa Awesome! I have 2 batteries that have literally just dropped under the charge threshold and now won't charge at all and they have both hardly been used.

[@seven1productions819]

Where do you get the wires from?

[@webuydronessa]

We buy them from a local electronics store, it's not a special type of wiring at all.

[@seven1productions819]

@@webuydronessa okay thanks

[@huanglinli]

谢谢！