Rex- c100 PID set to Fahrenheit

[@djkitty777]

Thank you so much for this video.

[@huilesessentielles2689]

thank you very much for your info:)

[@nothankyou63]

thank you very much

[@philipcousins5430]

Though you might think the REX-C-100 is showing Fahrenheit, it is off by 5 F or more. There are likely two more parameters that need to be changed to correct the slope and offset of the value displayed. If you have two controllers with one set for C, and the other for F; and the probes in the same liquid or a thermal block with a lab thermometer, the Centigrade is correct, but the Fahrenheit is not. F=9/5 C + 32 It likely can be done, but changing the 000 to 001, is just the start of what is needed to be done. 54 C reads as124 F, but should be 129 F.

[@bryannaquin3933]

I had to change my thermal couple set value mine was 29 degrees farenheit off kzbin.info/www/bejne/r4fblIOKhLVrh9E

[@billfleming6880]

Does not work with my BERM REX-C100 no unit setting on Code 0001. Must be variations of this PID?

[@randyrodich]

It does actually! That's the type I have. Instead of it saying "Unt" for unit like on his, yours will say "SL2". The default is "0000", which is Celsius. If you set that to "0001", it will make it display Fahrenheit. Hope this helps!

[@billfleming6880]

@@randyrodich Sorry Randy, my dad passed away in September he probably figured it out, but ultimately it doesn't matter anymore. Thanks for the reply though.

[@MASHA-l3g9d]

very useful information, but can you explain how to move from ° F to ° C ?? I will be very grateful

[@ronaldbaktis9441]

Where did you buy your C100. I haven't been able to find the Good-y one you have. I have a Berme and it doesn't match the instruction manual that came with it and has very limited ability to make changes. The LCK setting is 000 and yet several things seem locked including autotune.

[@bryannaquin3933]

Ebay

[@setourfree]

Thank You

[@pkskrap]

how do I change the configuration for type of thermocouple type, I connect it and it does not stop heating

[@thefamily_ak1863]

thank you sir

[@dougskucas5004]

Does not work on the berm rex c-100. I followed instructions, but there is no setting for "911". Any solutions, as programming varies between brands of this unit.

[@bryannaquin3933]

Sorry some Rex-c100 work some done depends on the manufacturer

[@randyrodich]

It does actually! That's the type I have. Instead of it saying "Unt" for unit like on his, yours will say "SL2". The default is "0000", which is Celsius. If you set that to "0001", it will make it display Fahrenheit. Hope this helps!

[@juanlopez4244]

Thanks for the video!! Have a question I have same pid won't blink when I try to change value on units any suggestions? Thanks

[@bryannaquin3933]

Check the lock screen it mite bo locked

[@barcksy]

Thanks Buddy, by any chance can you show me how to set it to cooling mode...(mine is set to heating mode)...have a good one. Rgds

[@bryannaquin3933]

Its easy once your in the 2nd menu look for (oud) on the display 000 is heating 001 is cooling set it to 001 for cooling

[@24dodgecummins1]

Ok so I can get into the units part, but it won't let me change any numbers

[@bryannaquin3933]

Check your lock menu make sure its set to 000

[@kaidikaidi6349]

Hi sir i have this model rex-c900fk02-m*an but icant get to cod menu ...any ideas

[@bryannaquin3933]

Hi kaid I downloaded a copy of your instruction manual it looks like you do not have a cod menu SL2 is the setting you need to change for farenheit set it to 0001. Hope this helps

[@kaidikaidi6349]

@@bryannaquin3933 sorry idont get it !

[@randyrodich]

very helpful. the instructions that come with the PID controller are next to useless.

[@Butter__knife]

Same as others , does not work on berm rex c100 . No unit settings. But thank you for the video

[@randyrodich]

It does actually! That's the type I have. Instead of it saying "Unt" for unit like on his, yours will say "SL2". The default is "0000", which is Celsius. If you set that to "0001", it will make it display Fahrenheit. Hope this helps!

[@thestavros4390]

where are the SL settings?

[@Alfonzo-y2u]

I have the good-I and it doesn’t have unt nor does it have the SL2 like the berm….

[@nolinicolas4237]

Gudday sir. How about i will use for cooling sir, all i need is 16-17 C means, 16C below it will turn-off and if 17C up it will turn-on. I will use as a switch(i will pluge my refrigerator) for restoring my pig semen. Thank u and God bles

[@bryannaquin3933]

In the cod menu same menu that you go in to change to fahrenheit look for (oud) set it to 1 for cooling its set to 0 by default for heating

[@nolinicolas4237]

@@bryannaquin3933 thank u sit

[@wretube]

Why do you hateto say japanese or chinese ares art people?

[@bryannaquin3933]

I was just babbling lol they are really smart people i meant no disrespect