Robo Race Robot using FlySky Transmitter | How to Make Robo Racing Bot without Arduino and ESC

[@aslamhossain1]

𝐒𝐮𝐠𝐠𝐞𝐬𝐭𝐢𝐨𝐧: Use Servo of the following model for better performance ---> Mg90s, Mg995, Mg996r 𝐒𝐨𝐦𝐞 𝐨𝐭𝐡𝐞𝐫 𝐓𝐮𝐭𝐨𝐫𝐢𝐚𝐥𝐬: Fast Line Follower Robot / Fast LFR / Fastest LFR / PID Line Follower: kzbin.info/www/bejne/iYWbfJeNhbKtppYsi=4OLW0cTDNwGmwwBY Robo Soccer Bot using Brushed ESC and FlySky Transmitter | How to Make Soccer Bot in Easiest Way: kzbin.info/www/bejne/pJWQgaGkotOoZpYsi=gGmbe2CjW1lpm47K Robo Soccer Bot using FlySky FS-i6 Transmitter and BTS7960 Motor Driver: kzbin.info/www/bejne/nanSd6qYmdqHhcUsi=8B-Z586qo14An_A3

[@mohammadkhalid6886]

Before opening the both servo motor, connect to channel 1 or 2 of the receiver (7:15) make the neutral middle position and disconnect ,,, make sure when you closing the both servo (3:20) then position of variable resistor (3:10) not change . दोनों सर्वो मोटर खोलने से पहले, रिसीवर के चैनल 1 या 2 से कनेक्ट करें (7:15) बीच की स्थिति बनाएं और डिस्कनेक्ट करें,,, सुनिश्चित करें कि जब आप दोनों सर्वो को बंद कर रहे हैं (3:20) तो वेरिएबल रेसिस्टर की स्थिति (3:10) मे परिवर्तन न हो। 👍

[@ishanahmed3236]

Joss vai MashaAllah

[@teamerror57]

Big fan vai big fan. From ugandah

[@mohammadkhalid6886]

Before opening the both servo motor, connect to channel 1 or 2 of the receiver (7:15) make the neutral middle position and disconnect ,,, make sure when you closing the both servo (3:20) then position of variable resistor (3:10) not change . दोनों सर्वो मोटर खोलने से पहले, रिसीवर के चैनल 1 या 2 से कनेक्ट करें (7:15) बीच की स्थिति बनाएं और डिस्कनेक्ट करें,,, सुनिश्चित करें कि जब आप दोनों सर्वो को बंद कर रहे हैं (3:20) तो वेरिएबल रेसिस्टर की स्थिति (3:10) मे परिवर्तन न हो। 👍

[@shakejones]

Thank you for sharing! Well done mate - NEW SUB 🙏🏻

[@aslamhossain1]

Welcome ❤️

[@FixitEasyDIY]

Great thanks 👍👍👍

[@aslamhossain1]

❤️

[@mohammadratul7921]

Joss💥

[@welcm_2_devill_world]

Any details about those rubber wheels..?

[@aslamhossain1]

85mm wheels

[@sarthakkumar8679]

Coupler detials ?

[@aslamhossain1]

For 37GB gear motor

[@sarthakkumar8679]

final bot size?

[@aslamhossain1]

22 by 22

[@StoryReader17]

Guys just buy a ardiuno its not expensive

[@aslamhossain1]

To ignoring coding.

[@StoryReader17]

My bad sorry bro but coding ain't rocket science

[@aslamhossain1]

@@StoryReader17 its not easy for everyone. That's why i've shown a simple method without facing any problem.

[@mohammadkhalid6886]

This project not required pc 😂😂😂 and any programming circuit,,, thanks bro,,, 👌👌👌,,,👍

[@mohammadkhalid6886]

If mangoes are found under the tree then why climb the tree?😂😂😂

[@PoojaSabharwal-i8t]

It about $47.23

[@maruphossain2826]

Speed control hoy

[@aslamhossain1]

Yes