Spur Gear Design Procedure based on Strength

[@bbb-th1vu]

here i am again in a indan engineer's channel and again, very usefull. thank you so much sir, exactly what i am looking for for days!

[@VISHALPANDEY-kv6mu]

Thanks sir Very nicely explained, only following yours lecture for Design of Transmission system

[@raghuljayagopi3027]

Brother you saved me from a big bang thanks a lot you nailed it congrats and thank you

[@rohan2609]

Why do you use a pencil, sometimes it's hard to follow, specially on a 5inch phone at 360p

[@ROBOMECHTRIX]

I really regret for the inconvenience caused. Although, I presume, all the videos have been tried to be kept at maximum quality possible. Pencil is easier for me to explain by encircling and pointing things out. You can definitely ask out all the doubts you have with you in the comments section.

[@saketseshadri7515]

abe wifi pe dekh na

[@johnjoe9397]

awesome explanation

[@AASHISHVENUGOPALBME]

Shouldn't we do the checking with the gear too, instead of just the pinion?

[@aashishvenugopal4892]

Adhitya The gear is under a lot more torque than the pinion, due to lower RPM. So, the contact and bending stresses for the gear would be higher than a pinion's. So why check the pinion instead of the gear?

[@johnykurmis3271]

from which book did you get the information ?

[@sonu72049]

Excellent explanation... Keep It Up! Could you please do the same for helical also... that would really be great(got exam running up coming monday)!

[@ROBOMECHTRIX]

Yes, let me try my best. My exam for the same on Monday too! Thank you for the encouragement!

[@krishnatripathi1750]

good explanation.

[@ROBOMECHTRIX]

Thank you! :D

[@enagantipurushotham8522]

Thanks for the information provided. What is Kbl, Sigma suffix -1 called ?

[@Newlighte]

Sir don't we have to calculate dynamic load (Fd) on gear , (Feffective) AND to check safety for wear failure By considering (Fwear)>= (fos) *(Feffective)

[@pratikb5833]

How to design a single gear (ratchet) not a gear pair. We want to use a gear with pawl in our project.

[@dontask23]

Awesome

[@lankavenkatabalasandeep15b31]

EXPLAINATION IS AWESOME SIR. BUT YOU HAVE TAKEN WRONG FORMULAES FOR h,Da IN STEP 14

[@dontask23]

Hopefully I found your channel!! ☺

[@tariquekhan6054]

Sir page secondfor ultimate stress sigma -1=0.35sigmau+1200 and you have taken as sigma-1=0.35 sigma u +120 (PSG8.19)TABLE 8.19

[@sanjaymaurya6900]

sir i want more lecture on spur bevel worm and helical

[@ROBOMECHTRIX]

You can always ask your doubts over here and I would try my best to solve them as soon as possible!

[@Rajeshraj-tg2wd]

How to selection of Life factor bending Factor of safety Fillet stress Endurance limit

[@Sspt22gmailcom]

Which databook your following bro....???

[@rohan2609]

How do you select material ?

[@ROBOMECHTRIX]

Material Selection is based on the type of question. If the material is not specified in the given problem, Steel or cast iron (data available widely) of any grade or alloy composition maybe selected from page 8.5 in the data book. Although the choice is solely dependent on you and you can select any material of your choice, just check whether or not all the values are present to plug into the different formulas.

[@rohan2609]

ROBOMECHTRIX thank you

[@ROBOMECHTRIX]

Please share the links for the videos with all your colleagues so that they are benefited as well! Keep Sharing, Keep Commenting!

[@sharathranga7509]

Sir can u please share the link of data hand book

[@ShivamVermaME]

how is i=3.5 in step 8'

[@hirendankhara211]

U are talking about taking 8.5 and 8.17 and 8.16... What was that?

[@ROBOMECHTRIX]

The link of the book from which the formulas are taken is Amazon - www.amazon.in/Design-Data-Engineers-College-Kalaikathir-Coimbatore/dp/8192735508/ref=sr_1_4?ie=UTF8&qid=1508657797&sr=8-4&keywords=design+data+handbook

[@ivordsouza4416]

U can buy this book (PSG) from the shops as well

[@ROBOMECHTRIX]

Yes definitely this data book can be bought from the shops. I was just sharing that the numbers in the video are from this book!

[@enagicindia5896]

Where is data book? can you share link. ?

[@bysanisudheer3619]

Sir how can we caluclate z1 teeth

[@strollerengineer660]

Which databook u follow

[@dontask23]

Narender Singh Design Data by PSG

[@dhineshakil9877]

Bro how to know the difference between gear life and Buckingham Lewis method

[@feeltheislam631]

Iam using mahadevan data book

[@dhineshakil9877]

Help me

[@mayurmalviya2929]

K madhavan k page no. Batao.. S!r

[@محمدعادل-ث1ع4ث]

lnned help