rx king , watch the way I polish the 2 stroke piston housing

[@ytfahmi4318]

Bang, saya pernah kolter di beberapa tempat, dibeberapaa tempat, dan cara pengamplasannya juga macam2, ada yang pakai solar, ada pakai air, ada tidak pakai apa2 cuma pakai amplas tanpa pelumas juga ada. Dan hasilnya paling bagus saat pengamplasan menurut saya pakai air, hasilnya kinclong chrome kaya kaca mulus😁

[@KULITEHNIK]

Untuk video yg ini sengaja saya bikin zig zag , klo yg kinclong silahkan cek di video video sebelumnya 😁

[@ytfahmi4318]

@@KULITEHNIK wahh mantap bang😁👍

[@rahimullahkhan164]

I have trail bike. Its piston stays about 4mm low in cylinder becoz the piston was not available in the market here. My question is can we scratch the head a bit just like u did to piston top and lower it in the cylinder ? Will it work?

[@scottyjones27]

Not sure abt that mite try cutting head to so combination chamber is smaller or cut head so center portions protrudes it the the cylinder × amout of Mm ?

[@ferdiyurdakul]

Don't forget to chamfer the ports.

[@ChiefCabioch]

You aren't using a bore gauge?

[@rinimemasak]

Amazing. I like it...

[@ChiefCabioch]

That's a rough ass hone, what grit stones?

[@scottyjones27]

Must be using some hard ass rings on piston to smooth out bore !! wear it in !!

[@MyZxcvb12]

Good work but you should look after your skin long term oil contact could lead to dermatitis on your hands.

[@qboncanel]

mantab boskuuuh,hadir menyimak boskuuuh

[@unilofrex1053]

Mantap jos mase

[@KULITEHNIK]

trimakasih boskuh 🙏👍

[@rezanugraha862]

Mantap dan

[@Agungjuhe]

Smngat smngat smngat

[@aji1697]

Bengkel daerah mana om

[@KULITEHNIK]

Tasikmalaya bose

[@aji1697]

@@KULITEHNIK biaya ganti liner fiz r berapa om

[@Mr_No_body_98]

Lokasi mana mas

[@KULITEHNIK]

Ciamis boskuh

[@riyanto4475]

@@KULITEHNIK n

[@Melamotor]

Mntp 👍

[@rohmanwahyudi566]

+ brapa itu mas?

[@cecepmarahayani4412]

Kang upami ob boring RX king.baraha

[@rijallumayung]

Ooohh, pakai air teh pucuk

[@peterbrockob5304]

Peter

[@arhymotor2678]

dari cara honingnya saja sudah geol2.yakin bisa lurus?

[@KULITEHNIK]

honing itu menyesuaikan lubang sama amplas boskuh, makanya ada yang namanya hapel klo honing lurus yang ada mengikis bagian tertentu , klo untuk meluruskan ttp di mesin korter sisanya di serahin sama yg namanya mesin poles

[@sukocorx135]

Kan dia muter, walaupun geol2 tetep rata semua kemakan, justru kalau lurus apa kamu bisa menjamin kelurusan 0°jika di dial? Kalau sampai mlengse dikit aja malah kacau karena cuma mengikis bagian tertentu

[@jamalstunt800]

​@@sukocorx135 nah ini bener.. dangdutan y mesti geol ya kan bang😂

[@sukocorx135]

@@jamalstunt800 yoiiii wkwkwk

[@solusimesinjccustom6499]

Sengaja bikin geol biar honing bisa ikutin bentuk liner .mangka di tiap sambunga as nya di kasi crosjoint biar geol

[@agussetiyo0037]

Nomer yg bisa di hubungi

[@KULITEHNIK]

Ig ada di deskripsi kang

[@agussetiyo0037]

Udah DM di IG tpi blm di bls dan minta nomer Whatsapnya kang