Samsung 65” LED TV - No Picture Bad Backlights - How To Replace LED Strips UN65 BN96 29076A 29077A

Samsung 65” LED Backlight Repair
CLICK HERE for TV Parts: www.shopjimmy.c...
In this video we will show how to replace the LED strips in this Samsung TV. It is recommended to take pictures during the repair process to use as a reference point. Be sure your TV is unplugged.
We have already removed the screws from the back cover.
Remove the inner back cover.
Before removing the outer cover completely, lift it a little bit and disconnect the cable on the main board, and the cable on the wifi module.
Disconnect the ribbon cables from the scan drive boards.
Remove the screws on the bottom of the TV that hold the bezel in place.
Disconnect and remove the speakers so that they do not fall when the TV is flipped.
Flip the TV over and remove the bezel.
Release the scan drive boards from the tabs.
Using tape, carefully flip up the scan drive boards and tape them to the panel.
Using suction cups, remove the TV panel.
Release and remove the four pieces of the panel frame.
Tape all of the layers of diffusion on the corners to keep them together.
Remove the layers of diffusion.
Remove the clear plastic clips on top of the reflector sheet.
Remove the reflector sheet.
Using a small pliers remove the small rivets that hold the strips to the chassis.
Our LED strips have tape over them, this is because this TV is a tester, so these strips have been removed before and we are just holding them in with some tape.
It is recommended to use double sided tape on the back of the strips when you are replacing them, instead of tape on the top of them.
Remove the LED strips from the chassis.
Unplug the strips from the power supply cable and then they can also be disconnected from each other, by pushing down on the tabs to release them.
The replacement strips should come with adhesive on the back of them to secure them to the chassis. If they do not, you can purchase double sided tape and attach it to each strip.
Align the replacement strips and connect them to the power cable and to each other.
Reinstall the reflector sheet.
Reinstall the larger plastic clips.
Reinstall the layers of diffusion and remove the tape.
Reinstall the panel frame.
Reinstall the panel.
Release the scan drive boards and secure them into position on the clips.
Reconnect the ribbon cables to the scan drive boards.
Reinstall the bezel.
Install the screws that secure the bezel to the chassis.
Reinstall the back covers and reconnect the cables to the main board and to the wifi module.
Reinstall the speakers and connect the cable.
TV Repair Made Easy™
© 2017 ShopJimmy.com, LLC.

[@masonmethot3186]

Big help! Got my LED strips replaced and fixed flickering and blue spot issues

[@davidalexander5985]

JB weld light activated worked for me. It was SO easy. My samsung diffusers with not fitting tight, and superglue did not hold after 12 hours. The light activated was sold after 10 seconds.

[@Sundance7055]

i just did my 50 " samsung and it works perfect ....thank you !!!...on mine you could see the burned out lights....also turn your backlights down to like 15

[@anthonybolden8625]

How do you know it's the backlights or the part that sends power to the backlights?

[@Jaqen-HGhar]

As someone who constantly works on TVs and from what I can tell, being subbed to your channel, knows the ins and outs of all the major brands. I have a quick question for you, if you were looking to upgrade your 51" Samsung PN51E7000 Plasma 3DTV and you want at least as good of a picture as that w/ HDR at least what would you recommend?

[@dovahkiin6642]

I know you asked this 2 years ago but I feel bad your comment didn't get reply. Did you find the answer to your question?

[@KillerWhale806]

I know it's been 3 years but did you ever find out if he got an answer to his question ​@@dovahkiin6642

[@elitescouter]

Thanks for the video, going to be replacing the strips on my 75 Samsung. Should be fun!

[@m4xatsgv]

EliteScouter where did u buy the led strips?

[@KnowNotNo_I]

I have a vertical shadow on my Samsung. What a life-saver! Thought this would be difficult❤

[@teemudgeon262]

Mine too. I haven't pulled it apart yet, but were your light strips vertical then instead of horizontal like in all these videos?

[@KnowNotNo_I]

@@teemudgeon262Yea, I still haven’t tried to fix yet.

[@teemudgeon262]

@@KnowNotNo_I Lol, I'm just gonna get a new tv. Might try pulling the old one apart down the road, but I don't think I'll order any parts until I see what's behind the screen. Best I could find was $100 for 2 horizontal style LED strips and the whole thing will actually need 6 so bare minimum cost will be $300....plus shipping. Plus I'll prolly just fuck it up and chuck it all out into the trash.

[@pmatioli]

Do you know if the same approach works for Samsung QLED NEO Tvs?

[@MrOzzieoz]

Very detailed and helpful. I did wanted to see the how you would test the backlights to determine which ones were bad.

[@00Skyfox]

I have the UN65J6200AFXZA-IH02 model, but I don't see that on the compatibility list for these lights. Closest version I see is the -AH01. Are these lights also compatible with the -IH02 version?

[@asmaalaya1556]

Hello . Please does anybody know where to find strips for a 65 inch curved tv.

[@JLIII-hh1pi]

Same strips as flatscreen. Light strips are flexible.

[@r99pinball24]

Any ideas on how to open up a un65mu6290vxza? There's no screws on the back and I'm scared :P

[@travisfender8851]

If you look at the bottom, there are 2 holes at each corner. I used a small screwdriver to slightly pry up on it then used a guitar pick and went around the whole panel. It worked like a charm.

[@michaelcheng562]

How to remove the bezel 75" Samsung UN75NU800DF?

[@porquemudamosparaorlandofr3016]

Hi, good night. I have a tv Samsung 55” serie 6, UN55MU6290FXZA; please, do you have to sell the backstrips led? Please, help me....

[@royalmarshall4577]

Looking for un 65c 6500 vsxza led strip

[@steveevans7046]

Great help but has anyone a step by step for a QE55Q700TAT as the frame is attached to the display ?

[@MaryannWright]

The tabs before getting to remove the reflector sheet are not twistable - it seems like I’d have to break them in order to get them off. It’s a Samsung UE40H5500. Any help? I don’t want to break them all off!

[@jean-lucpicard5510]

switch them round see if that works?

[@absolutemesquitecreations329]

Hi I have a Sanyo dp50747 plasma tv. The screen will be working fine the randomly will start blinking off and on as if between scenes or between commercials. It does this at random times and I haven't found any common situations that could cause it. Totally random. It will start blinking very fast then slow down and sometimes stop for a minute in between blinks. And then sometimes it will be fine for hours. I don't get it. I would so appreciate any advice. I'm very handy with electronics but this has me baffled. Thank you

[@kamrantahooni9439]

عالی بود دمتون گرم

[@seth0351]

How do you remove the retainer clips that hold the diffuser backing to the chassis? He just twists them off and then back on. Mine won't budge.

[@DanielBjorndahl]

mine broke. I super glued them back in

[@seth0351]

@@DanielBjorndahl Turns out mine clip in and you have to release them from the other (back) side. Naturally you have to remove both boards to get to some of them. I broke two of them trying to get them snapped back in, but there are plenty and it does just fine without them.

[@DanielBjorndahl]

So I did this repair but now I have a vertical lines up and down the middle of the screen. I see the "no signal" scanning on the right hand side of the screen but not the left. what did I do wrong?

[@bens3767]

Did you check your ribbon seating on the t con board?

[@PrasadHugar-i8r]

Display removing too name pz tell me

[@selengebatbold6607]

Hello... Samsungs tv EU65JS8085/UE65JS8590. 8 SERIES

[@bct321]

Will this work on a curved screen?

[@digvijaysalesservicespune7030]

54inch leth of each back light ,11 strep in this tv

[@genebutts1978]

Just replaced the back lighting for this tv although 55" and now i see white lines across the screen. i am thinking i got the light diffusers reversed when i put them back as i did not use tape to tape them together prior to taking them out.They are not small white lines it looks like you can see the led strips through the lcd . Help anyone?

[@wrestlepsu99]

Does anyone know how to remove the LED strips from the interface board without damaging the housing?

[@PrasadHugar-i8r]

How pz tell me

[@rickstraiko5728]

what order do the delusions go . i didn`t tape mine together

[@mohamedmo8177]

Maternant Samsung la mauvise marque moi aussi jai ce problème et jai changé 2 fois les lumbe

[@digvijaysalesservicespune7030]

I want original back light of samsung model = LH65mdcpl gc/xl

[@sammieharris6084]

i have samsung un65js8500 edgs leds how many do i need to order

[@W.Dennis]

Don't forget to reinstall the speakers lol

[@portanova47]

What a pain in the assss!!!!!

[@bens3767]

It's really not that bad. Once you get one finished you'll want to go looking around for more to fix up it's so rewarding. I flipped a TV I found in the trash after replacing backlights made a cool 200.00

[@moasserreza]

like❤

[@nickhaley1212]

Would you know what my panel model number would be, since there is no sticker on my panel, I need to order replacment LED strips, SAMSUNG Model # UN60H6203AF TYPE- UN60H620 MODEL CODE- UN60H620AFXZA VERSION- HH01 S/N- 02Q43CDF500105R