I'm a new member... worth the £2.99 a month. Great advice and informative content.
@AllenHart9993 жыл бұрын
Thank you very much.
@waynenixon7293 жыл бұрын
I'm sure I'll be one of many that join, with some of the subscription going to charity everyone is a winner! Thanks again Alan for all the time and hard work inc honesty that goes into your videos. Did you do your training with Derek of Tomkat gas training? Can't remember if it was you or another well known plumbering / gas engineer youtuber.
@AllenHart9993 жыл бұрын
@@waynenixon729 I will add you posts in the community section going forward. We can all work as a team to do video that people want. Thanks again. kzbin.infocommunity
@garydulson90183 жыл бұрын
Please specify that you can't use poly pipe, only copper on secondary return systems.
@AllenHart9993 жыл бұрын
@@garydulson9018 You would need to speak to the manufacturer. Normally we use copper or MLCP that's approved. Thanks.
@user-hl4hx2nd4h3 жыл бұрын
Allen, you do some cracking work for communities and help out gas engineers to. All round good egg. Happy to chuck a few coffee's over. Keep on going pal.
@AllenHart9993 жыл бұрын
Thank you very much.
@johnburns40173 жыл бұрын
I have fitted secondary pumps on systems using electronic body detectors in bathrooms. The pump is only on when someone walks in. This saves a wedge in heating bills as secondary circulation on a timer is continually dragging heat out of the cylinder. A great idea for just the far reaches of a H&C water installation. Great for domestic houses. As it is not continuous circulation (it is on demand) plastic barrier pipe can be used.
@thomasgoodman38763 жыл бұрын
Loving that idea, awsome
@goheat3 жыл бұрын
Hi John. Interesting approach of controlling the pump. What detectors do you use ?
@johnburns40173 жыл бұрын
@@goheat see post above.
@elwittinio28652 жыл бұрын
How do you overcome the legionella aspect if it’s not used for a while. Like usually they are on a timer, just asking 👍
@johnburns40172 жыл бұрын
@@elwittinio2865 Legionella predominately lives in the cool stored water in the cylinder. When heated over 60C it goes away. So you heat up the cylinder, as per normal.
@johnvissenga32810 ай бұрын
thanks .... needed to self install a large cylinder (on a boat) and first time ever come across secondary return. thankyou, nice and clear explanation , got it straight away. Unfortunately not practicable in this particular situation due to lack of access to add further pipework, instead fed a 15mm feed (10 metres long) down the inside of the existing 22mm run to reduce the water wastage (more important than flow rate here)
@AllenHart99910 ай бұрын
Thank You
@2011zurich3 жыл бұрын
After wasting so much of my (long) life waiting for hot water to appear, and learning about this system as a child (and also that most of Scandinavia have always done it like this), I've always wondered why it's not done more often. Just the extra cost, I guess... but so much better than all that water going to waste while you wait for the hot. Great video!
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@nickadams52123 жыл бұрын
Haha 😂 that head popping out the bath. Thanks Allen 👍
@AllenHart9993 жыл бұрын
😂😂😂😂😂
@AllenHart9993 жыл бұрын
Customer was so happy he jumped in while filming lol
@nickadams52123 жыл бұрын
😂😂
@treacheroustiger55713 жыл бұрын
Just became a memeber. Thanks for putting out these videos. Enjoy the coffee!
@AllenHart9993 жыл бұрын
Awesome! Thank you!
@kaiser91003 жыл бұрын
I work in the commercial sector Allen and I’m seeing more returns being added to the cold water supply. This is due to new buildings being so airtight and heat efficient that it is warming up the cold water in the pipes, even when insulated.
@AllenHart9993 жыл бұрын
I have never seen it done like that. Thanks for sharing.
@johnnyarmstrong26955 ай бұрын
Thank you for informative video. Great you have contribution to charity. Thanks again
@sharesgames95462 жыл бұрын
Many old houses in the UK, probably millions, have water pipes running through and/or buried in walls and in concrete slabs. When you draw hot water you lose a lot of heat into the slab, and with recirculation you lose even more heat even when you are not using the bath/shower/whatever. Maybe an idea to have a thorough inspection carried out before installing recirculation.
@billybobhouse95593 жыл бұрын
Good video, I wasn't sure how this worked.
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@gulammangerah11373 жыл бұрын
Hi Allen, Thank you for sharing the information. 👍
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@jamiecharles76453 жыл бұрын
Really helped mate . Didn’t know a few things mentioned in the video 👍🏽
@AllenHart9993 жыл бұрын
Thank you for taking the time to watch my video.
@davidoshea15363 жыл бұрын
Brilliant Allen. 🔥🌟
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@quadrantheatingelectricspl29078 ай бұрын
Another great Video Allen, thanks
@craiglewis67093 жыл бұрын
See this all the time being in the commercial sector only ever seen it twice in houses and one of them actually fitted a towel rail on the hot water system 😄
@AllenHart9993 жыл бұрын
No way that's crazy.
@loafersheffield3 жыл бұрын
Just really well lag the towel rail. The heat loss is prohibitive if primary services and secondary returns are not really, really well insulated.
@haydensnart24233 жыл бұрын
You can install towel rails on the secondary return if they are suitable, I have come across this myself. I believe they have to be made from brass and very expensive
@petedevon3 жыл бұрын
Cheers for sharing. Easy to follow videos 👍👍
@AllenHart9993 жыл бұрын
Glad you like them!
@fionnan2811happy4 ай бұрын
I destratify all my cylinder installs. Tee of the secondary return to the drain off with another tee and link the two. I used to fit a pump but have found it is very good to create its own convection currents and destratification is achieved naturally. Been doing this for 16 years and always works. If there is not a secondary return I tee off the hot outlet to the cold feed and it does the jod too👍👍👍
@leighdavies7477 Жыл бұрын
Thanks for the content Allen 👍
@AllenHart99910 ай бұрын
My pleasure!
@AllenHart99910 ай бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@quadrantheatingelectricspl2907 Жыл бұрын
Another great video Allen !
@MrAbdulHaque3 жыл бұрын
Was useful thanks. But this system needs top-quality insulation to help reduce wastage all ready found with unvented systems compared to combi systems. Will be nice to see a video highlighting the best insulation, both from a heat and sound perspective, available in the market.
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@abchannel37373 жыл бұрын
Excellent Allen 🌹🌹💐💐
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@globalste Жыл бұрын
I have a hot water return on my unvented cylinder, annoyingly the people who fitted it put it from a t-section of the regular return and it just had the regular pump running constantly for a 80cm piece of pipework! Obvs knackered the pump.
@garydulson90183 жыл бұрын
Worked on a barn conversation with another contractor, wouldn't agree to lag the secondary return or the fact that you can't run it in poly pipe, has to be in copper. Walked off the job
@AllenHart9993 жыл бұрын
Gary Dulson You can also use some MLCP pipe. Thanks
@hollychow23643 жыл бұрын
thanks Allen for your content
@AllenHart9993 жыл бұрын
My pleasure!
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@accesszero48033 жыл бұрын
Ive just fitted one, what a diffrence it made , i didn't time it, i set it on a permanent temperature because its a busy household
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@johng58067 ай бұрын
Gotta say - nice video, well explained :-)
@ranjitpatel4963 жыл бұрын
Thank you for your time
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@ranjitpatel4963 жыл бұрын
@@AllenHart999 I have subscribed very useful for me as a gas engineer & plumber.
@user-dz6pk9vu8w Жыл бұрын
Yom man good teacher
@AllenHart99910 ай бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@temetam Жыл бұрын
many thanks
@farhanprine Жыл бұрын
Thank you for this explanation buddy 👊🏽
@ketansoni584610 ай бұрын
Great video Allen! Couple of questions. What is the purpose of the check valve and where would it need to go? Inbetween the pump and cylinder or before the pump? Are gate values enough to isolate the pump if it needed to be serviced or replaced or would an additional isolated valve be required? Final question you mentioned perhaps needing a largeer expansion vessel what determines whether a larger one is required or not?
@AllenHart99910 ай бұрын
Stops heat going out of the cylinder.
@MobinC973 жыл бұрын
Cracking video Allen thank you soo much for this informative video!
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@warriorsofwarmth3 жыл бұрын
Im currently promoting this channel, GB Mr Hart
@AllenHart9993 жыл бұрын
Many thanks. Hope you are well.
@bekskayll68413 жыл бұрын
Thank you so much, really enjoying your videos! you are very clear in you explanation and it is sinking in. :D
@robodog35712 жыл бұрын
Very useful info thanks
@loafersheffield3 жыл бұрын
I was nagging my primary contractual employer (an entertainment business) for permission to replace a 2ndary dhw pump for three months. Yer see, all specific purchases over £50 have to approved by the management. Those pumps are not cheap!! Then the external water safe guys attended to check and issue a certificate of conformity and bollocked ME, as the dead leg return was, well, dead! I got a stern telling off by the manager. Then I showed him copies of my requests placed on his desk, to purchase the pump going back over 2 months. When I got home, the missus bollocked me for forgetting to put the bin out. Can't do reyt fer doin' wrong! The pipes have to be really, really well insulated too.
@AllenHart9993 жыл бұрын
Thank you for taking the time to watch my video.
@Eleven1452 жыл бұрын
Thank for the info
@BlueSquad003 жыл бұрын
Very helpful thank you
@stuartbarnes9017 Жыл бұрын
Hi Alan, I have just installed a secondary circuit on my gravity system but when i start the pump on the lowest setting it blows water into the header tank which is only about 2 feet above the cylinder because of a low roof, is there anything i could do to prevent this as i can't leave the new circuit connected, Thanks
@bsl8492 жыл бұрын
Informative video. Q: can two loops be made on a single secondary pump? I ask because we need to feed two ends of a long building, otherwise it would result in a single loop of approx 65m. All new install, all new pipework.
@AllenHart9992 жыл бұрын
yes.
@suzannahwhite4292 Жыл бұрын
I had a secondary return system installed, however, the plumber failed to insulate the pipes and the system loses heat within 20-30 mins of running, meaning huge bills keeping the water hot. I've had to turn it off. The plumber says insulation wouldn't have made any difference. That's not what I'm reading.
@StanSuchy10 ай бұрын
Do you know about any hot water recirculation solution for UK without dedicated hot water return pipe. Danfoss does a solution but it seems to be dedicated for US market. Not sure if that could be used in the uk
@AllenHart99910 ай бұрын
not sure sorry
@kenneth1523 Жыл бұрын
Hi. What household brands recirculate into the top of the water tank like in your video as opposed to the ones like Rinnai that recirculate into the cold water inlet which doesn’t make sense to me if you want max or constatent hot water temps?
@AllenHart99910 ай бұрын
You can get them from most brands. Thanks.
@dmac85953 жыл бұрын
Can you do a video for multiple say 10+ out let’s on different floor levels all more than 6 meters apart, by my thinking you would then install tees as close to each outlet would a non return valve be needed on each primary where the tee comes off ? As essentially your going to having multiple small loops coming back into the secondary return main line back to the cylinder ?
@airwebber8 ай бұрын
I have one of the recirculators that uses the cold line. I want to use it and run it's own circulation line. I don't think my hot water heater has that inlet recirculating line like your drawing. How would I do it to work?
@mushtaqshah9390 Жыл бұрын
My hot water tank is in the garage and they have installed one of these. My question is should this be on continuously? What is the best speed , mine is a archergas system with 3 settings. Would i cause any problems by having it on continuously? Many thanks
@muki10083 жыл бұрын
Hi Alan, hope all is well, Please can you provide a video on how to connect heatmiser u8 wiring centre to, ufh and its actuators, as well as 2 wireless thermostats one for the ufh and the other to standard radiators, I have 2 wireless thermostats with switches any help will be great Thanks.
@AllenHart9993 жыл бұрын
If i do any i will see what i can do. Thanks.
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@emilh82313 жыл бұрын
Hi Allen, thanks for the content, I've found many of your videos very helpful! I am wondering with secondary return and the pump working, If megaflow is on ground floor and supply various bathrooms, will there be any pressure and flow drop when open tap in loft ensuite? As I believe circulation pump is working all the time, or it shuts when the outlet is open?
@brmelectric3 жыл бұрын
If an expansion tank was installed being a closed system, would that ever have to be purged occasionally or one time deal. Great videos by the way.
@MyMonkey19733 жыл бұрын
the closed(sealed)system sounds like its on the heating, would not have a expansion tank on a unvented hot water cylinder, hope i guessed right what you was asking
@AllenHart9993 жыл бұрын
I will do a video about this soon. Thanks.
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@ek68683 жыл бұрын
Good video,why can't you use a normal central heating pump on this system the pumps job is to pump the water around?
@grahammay13 жыл бұрын
because normal pump body is made of cast iron and would corrode over time contaminating the water
@ek68683 жыл бұрын
@@grahammay1 tanx👍
@AllenHart9993 жыл бұрын
Very good question. Graham is correct. Thanks.
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@craiglewis67093 жыл бұрын
Has to be bronzed mate otherwise it will corrode- used to be yellow pumps but not so much with the newer versions
@songzhou Жыл бұрын
But how much for the electricity, since the pump is running 24 hours.
@andymav30232 жыл бұрын
Hi Allen excellent video…quick question would pipe up that secondary return along any part of the hot feed in the house and send it back to the cylinder ?
@gerardbarlow417 ай бұрын
What is a tank lock that was mentioned at 6:03?
@samuelbeckett4853 жыл бұрын
Great video mate. Just a question. The pump will circulate into the cylinder with the check valve after the pump ? Thank you!
@johnieboy222 жыл бұрын
pretty helpful
@user-ks7ld8vc7k Жыл бұрын
Helpful
@douglasjasse25882 жыл бұрын
I have this type of system with 300 litre tank, being oil fired with solar assist, however when the recirculating pump runs the volume of cold water in the return quickly cools down what at the top of the cylinder, so one only receives warm not hot water, any suggestions appreciated Thanks Doug
@gentibifsha60882 жыл бұрын
Is the pump pushing the water back to the cylinder?
@chrisirwin11722 жыл бұрын
Hi Allen - thanks for the video. What if there are two bathrooms and a kitchen all at different ends of the house? Can the three secondary returns all be gathered into a single connection to the bronze pump and then into the return boss to the HW cylinder?
@pumpkinhead4562 жыл бұрын
You can, but you also then need valves to balance them, otherwise one circuit might rob all the heat. I'm not sure if it's in the video, but it must be copper pipe too
@mylifeintheuk20932 жыл бұрын
Hello, I’m seeking a piece of advice. We’ve 12 years old Conventional gas boiler at home we recently moved. There is no thermostat so we’ve to switch on/ switch off the boiler for heating. For hot water, there is a separate electric water heating system too. Is it advisable to get the thermostat for the heating system which is costing 250-300£ with installation? Many thanks
@briancarney46093 жыл бұрын
Alan if i want to put a connection for return circulation on my unvented tank what fitting do You use after cutting hole in tank ive used one years ago but what is new version I think last one had slot and pulled it with a wire from inside then put nut on ???
@AllenHart9993 жыл бұрын
I have never done that. You would be best to give the manufacturer a call and ask them. Thanks.
@barriedear59903 жыл бұрын
Dies it matter if circulation pump is on the flow or the return? Ours is on flow just now, but getting a new cylinder fitted shortly.
@AllenHart9993 жыл бұрын
The pump is normally on the return. Thanks.
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@kirstywilliams48523 жыл бұрын
Could you give me advice about my cylinder is not filling up with cold water for hot water no hot water is coming out any of the taps in the house?
@martinbinney2 жыл бұрын
Nice video. Is it essential to have a cylinder with a connection for a hot water return? Or can this be achieved on a cylinder with only two connections (cold in at the bottom, hot out at the top)?
@martinbinney2 жыл бұрын
After a bit more research I see that using an Essex flange to create an new connection on the cylinder is the way to go.
@Niall-yo1uo3 жыл бұрын
Hi Alan, how are you. Could you put a pressure switch inline with the pump to control the pump instead of a timer on the pump? Would this be possible?
@jonathannbullitt2 жыл бұрын
I don't understand that 25% connection on the return. Can somebody explain?
@deanchapple13 жыл бұрын
What if you have multiple hot water out let’s? You you put one tee per appliance? Or just one tee on the furthest appliance?
@AllenHart9993 жыл бұрын
Very good question. You have it as the loop in the video, Then you use multiple tees. Thanks.
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@sydsyd3 жыл бұрын
👍👍👍👍👍
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@Lonzohiggins9992 жыл бұрын
Do you only have to tie the return from the furthest fixture ? What about the rest of the fixtures ?
@AllenHart9992 жыл бұрын
Normally just on the furthest. Thanks.
@heatz24843 жыл бұрын
How far Pretty much should that sink be to use a secondary return?
@AllenHart9993 жыл бұрын
Not sure what you are asking? Thanks.
@heatz24843 жыл бұрын
I have the cylinder on the loft and the furthest tap is the kitchen tap which is approximately 20/25m away from the cylinder . My question is :Will this system need a secondary return ?
@carlosbambos2 жыл бұрын
Are there any combies that have this system?
@erikvanvelzen3 жыл бұрын
When my human is fully cooked do I need to add anything?
@AllenHart9993 жыл бұрын
😂😂😂
@markpugh17642 жыл бұрын
Hi Allen, can you use mpress on a secondary return system. Thanks
@AllenHart9992 жыл бұрын
Yes
@johncoen14683 жыл бұрын
Allen why has the sec return to be copper and not plastic??
@pumpkinhead4562 жыл бұрын
I've done a lot of reading in to this - in short, the majority of plastic in the UK does not allow continuous circulating under British Standard testing; if a pipe happens to burst your insurance not pay out. Some argue that plastic degrades quickly through oxidation, reducing lifespan by a third, others say that's rubbish. I only know as my builder did mine in plastic, and now I'm trying to get money back!
@Chris-js4yq3 жыл бұрын
👍
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@Zaine223 жыл бұрын
Whats the solution for long runs on a combi if any
@AllenHart9993 жыл бұрын
Thats a really good question, The answer is don’t install a combi. Thanks.
@Zaine223 жыл бұрын
@@AllenHart999 lol what if your already padt that point 🤔🙈
@AllenHart9993 жыл бұрын
@@Zaine22 Not much you can do then. Sorry
@Zaine223 жыл бұрын
@@AllenHart999 thats what i thought
@paul_my_plumbs_uk3 жыл бұрын
👍👍👍AL ❤️U MAN
@AllenHart9993 жыл бұрын
Thanks very much for your comment, please consider subscribing to support the channel 🙂
@paul_my_plumbs_uk3 жыл бұрын
@@AllenHart999 already subscribed have been for ages 🤜🤛👍👍👍
@AllenHart9993 жыл бұрын
@@paul_my_plumbs_uk Thank you. KZbin doesn’t show us.
@mrv58013 жыл бұрын
COULD THIS BE FITTED TO MY EXISTING 15 YEAR OLD MEGAFLO UNVENTED CYLINDER AS THE HOT WATER TAKES AGES TO COME OUT OF THE SHOWER IN THE MORNING??? CAN IT BE FITTED IF THERE IS NO SECONDARY RETURN INLET ON THE MEGAFLO CYLINDER???
@MyMonkey19733 жыл бұрын
No. on the old copper cylinders it was possible to fit a boss outlet but a megaflow is a stainless steel one and if unvented would not be someting could do one self
@johnburns40173 жыл бұрын
I have seen one fitted with the DHW return pumped into a Surrey flange in the draw-off tapping on the top of a cylinder. That means the DHW return cools the very top of the cylinder slightly.
@rickbaguley79973 жыл бұрын
If your unvented cylinder does not have a secondary return boss already, it is acceptable as long as it is also in accordance with the manufacturers instructions to tee the return into the cold water supply pipe just before it enters the cylinder. However you also need to bear in mind that Hot water pipework on a system with a secondary return has to be copper/steel because plastic is not designed for permanent high temperatures and it has to be highly insulated because you are effectively increasing the surface area from which heat can be lost. Also any work on an unvented cylinder has to be completed by a plumber with the G3 certification
@craiglewis67093 жыл бұрын
Just tee it back into the cold feed just make sure you fit a non return valve
@wirdy13 жыл бұрын
@@rickbaguley7997 would teeing into the cold feed cause the f+e tank contents to get gradually heated by convection?
@lutherbryson70496 ай бұрын
Speak southern English dude
@veronicahart4503 жыл бұрын
👍👍👍👍👍👍
@AllenHart9993 жыл бұрын
Thank you for taking the time to watch my video.
@steveturner76423 жыл бұрын
Super video many thanks
@AllenHart9993 жыл бұрын
@@steveturner7642 Thank you for taking the time to watch my video.