Series X Plus 8 Keg Kegerator - Installation Video

[@robbdenney1060]

Just set up the 4-tap Series X this weekend. Awesome product! Some quick tips: 1. For the 4-tap tower with the inside screws, instead of the drill extension and masking tape method shown in the video, this is much simpler & easier: hold the tower in the air, insert the four screws in the holes with your other hand, hover the tower about 1 inch above the kegerator, align the screws into the holes (there is just enough dead space for each screw to drop in and hold in place), VERY gently lower the tower leaving all 4 screws in place, VERY carefully tighten each screw down enough to hold in place while you tighten down the rest. 2. The screws on bottom for the caster wheels where ridiculously tight on my unit and shattered my drill bit. So have a socket wrench on hand (luckily they are hex screws). 3. I stole this tip from another video - gently press and twist the tower cap onto the thin plastic packing foam to make a perfectly fitting foam insulation circle for the top of the tower. 4. Use a keg with appropriate cleaning solution (or just warm water) to clean out the lines first and test for leaks (so that warm water or cleaning solution spray all over instead of beer). I was very carful and still had 1 tap that didn't tighten in correctly. Thats's all. Great product! KegLand continues to lead the way in new product innovation and reasonable prices.

[@KegLand]

Thanks for the feedback and really appreciate the extra tips. We will have to include those in the next vide. Thanks Robb.

[@davewebb8777]

Thank you for the video. The instructions are very helpful and simple. Just a quick question: I did several gas leakage checks leaving the system for several hours. Each time the high pressure gauge showed zero while the low pressure one was ok. Any advice is appreciated

[@KegLand]

Sounds like yo may have a very slow leak

[@peetei]

Hey I'm super excited for this product, just wondering if there going to a a soccer goal/ bridge style modular font pack or kit that fits and hopefully with four ss nuka taps?

[@KegLand]

We are working on some modular fonts ourselves but at the moment, the current modular fonts would not be compatible.

[@clintwatson4754]

I got the 8 keg but can't fit them all in i need to see the layout please its like a tin of sardines with 2 extra sardines. If it was bigger say 50-100mm would be better

[@johnrobinson8941]

this is probably not related but it's regarding the berewzilla, I was wondering if it was possible for you to do a video on how to brew in one of these, I know someone who has switched from extract, kit & kilo to all grain and has bought a brewzilla and is wanting tips, before the all in one brewing systems were available there were videos on building mash tuns and then brewing an all grain batch etc but there doesn't seem to be a instructabe video on how to brew all grain for the first time in a brewzilla

[@lvory]

Search for "david heath brewzilla quick start guide" here on youtube. When I started out Davids videos were a massive help.

[@KegLand]

@@lvory Yes David Heath has a great channel and he produces some really helpful videos. I would second that comment.

[@KegLand]

Yes that is fair enough. Already a lot of videos existing on this and we also have the PDF download manual that you can use for reference too. With that said you can also ask our customer service team if you have further questions.

[@johnrobinson8941]

@@KegLand I was referring to you doing a video on how to brew all grain if you have never brewed all gain before in a brewzilla, you promote them on here and there are a lot of people switching over to all grain who don't have a clue how to brew all grain, all of us who shifted from the mash tun 'esky' to the all in one brewing systems already knew how to brew

[@KegLand]

@@johnrobinson8941 Yes that is a fair point. I will take this to the others. Probably what we need is a video series on all grain brewing, fermentation and sanitation for beginners. I would agree this is probably a good idea.

[@PortlyGentleman]

Awesome video I am eagerly awaiting the upright refrigerator you teased a few months ago ! Hopefully that one will make it to the states?

[@KegLand]

Yes all the models we have will end up going to America.

[@PortlyGentleman]

@@KegLand I like the sound of that 🍻

[@ryanc3001]

liking this fridge to run 4 kegs plus have capacity for cans etc (with the wire rack accessory) but hate the look of 1 single offset font... wondering about a centralised hole....

[@KegLand]

We have no plans for a centralized hole at this stage. What about 2 fonts with just 2 taps on each side?

[@ryanschram]

Is there a USA distributor for these?

[@KegLand]

We should have these arrive to www.morebeer.com soon. If you contact them they might have an arrival date for you.

[@christopherhoare5139]

Are the new disconnects going to be better at handling starsan than the duotights? I haven't had an issue yet but have seen cracking.

[@KegLand]

Hello Christopher. It might be worth you having a look at this document: www.kegland.com.au/media/pdf/duotight%20design%20revision.pdf The duotight fittings were revised some time ago so your cracking issue has already been solved.

[@thomaskelly2572]

Is there no insulation on the 4 tap version

[@KegLand]

Foam noodles is what we recommend to insulate your product lines.

[@dylanparry1815]

Will two 58l kegland kegmenters fit in this ?

[@KegLand]

Yes the 58L KegLand Kegmenter will fit.

[@zappaland]

Hi! Is on line a video on how to sanitize Fermzilla? Tnx

[@KegLand]

This is a good video by Gash using the Bucket Blaster so have a look at this one: kzbin.info/www/bejne/fYjPlZt8aMqVi6c Alternatively if you did not want to purchase the bucket blaster you can just clean and wash by hand. Just use the PBW and Stellarsan and this will do the job.

[@brettmeekings9185]

Hi I was wondering if you could me out? I have a Kegerator with a Birra Moretti 30L Keg chilled to 3 Degrees Celsius with a 60/40 mixed gas, my beer line from keg to tap is 2 meters in length which is also cooled. I am just wondering pressure I should set my regulator too? Feedback would be greatly appreciated.

[@KegLand]

Hi Brett give us a call during business hours and we can help you out.

[@MrBellda]

100%, you need 3 or 4 ports at the rear of this unit... 🙂

[@Sunline7]

Great Vid , Thank you

[@KegLand]

Glad you enjoyed it

[@Greta-Thunberg-How-Dare-You]

that was not me who thumbed down your video either, Mr Slug also has trolls on his channel

[@karlmagnusson6931]

Love your work Greta!

[@KegLand]

@@karlmagnusson6931 Great to see you are back Greta. So will you be getting a Series X Plus soon?

[@universeofmaltedbeers5957]

hello I just bought the x plus series, and it is impossible to put 8 was soda in it... I am disappointed with this false information.

[@KegLand]

what do you mean. Are you using our corny kegs? I have put 8 kegs in myself so I am 100% positive that it works. the kegs must be placed in the correct sequence to fit them in. I would suggest looking at our website as we have a layout diagram.