It doesn't take much effort to rinse out the drip tray.

Nice

How annoying is needing to empty your drip tray? Well, now you need to empty your waste basket instead and also clean your drip tray

Drain fitting be like "did you just assume my gender"

Love the blooper. 😝

Well done, sir.

Looks very cool. The one without a chiller for a cheaper price would be nice, though. I have a kegerator setup so no need for a cooler. Or maybe a compressor that adds nitro to the existing lines on the go? Just saying :)

Would this work to dispense nitrogen beers provided we attached the appropriate spout? Is this good for commercial kegs as well as home kegs?

Chill the water before carbonating it? Didn't know that...

Wow - Awesome device but HORRIBLE video. Redo the video with one person doing the work and another person recording. Do some BASIC editing. Get OFF the metal table and so on. Half the time the item was off the screen (not just off the center). Oh and sell the device with WiFi Charger pre-installed please..

Can't wait to use these awesome piece of kit !! At around the 22 minute mark, you say the gas can be fitted at the top. Could you run through how to fit this? An elbow will not fit on the bottom of the reducer, at least not in line with the regulator, & the hose is too rigid to bend into place. Any help would be greatly appreciated.

The 24v is a huge down side .. means its not plug and play. I have to set up 2 x 12v batteries seems crazy .. why not just run it as a 240v with some water proofing?

Can i use my old tap springs in them?

Rcently perched this kit. I'm getting product overflowing the head of the still. Is it faulty, or is the tap flow rate to low. What's the recommended flow rate & temperature. What temp do I set the digboil to. It's set at 100*c at the moment

Fully charged, registerd and calibrated, but cannot find a way to get any info out of the thing. Just a 'No data has been received from your device' message. Most of the buttons on the interface do nothing, and in any case their intended functions are unclear. This device has such great potential, but let down by a clunky interface and a shortage of instructions.

How much does a system of 200ltrs coast?

Nice does it show the end product abv?

I specifically came here looking for this product, so the answer is yes

Trying to set up a profile on the app you need a degree. No instructions.

Is that pizza turner coated in teflon?

Instead of running glycol through the jacketed tank, can hot water run through it to heat the tank? I make mead and I am looking to figure out a way to heat the mead up to 140F in order to pasteurize it. Once pasteurized, then I can back sweeten if needed. I am trying to figure out a way to pasteurize in a fermenter.

I'm not sure how I miss this one. Super cool 🍻

Why would you want to connect these?

When will this be avail in US?

How long do you set the purge for for a 500ml can ?

Do you have plans to make a stout nozzle for the mini?

For this price why don't you include power adapter?

good information

Hey Key! Double the signal strength you say. I.e. you get 3db better signal? Or do you go from like -80 to -40dBm ? Cause, thats like 10.000 times better signal :)

will the 8" lid be available for purchase?

Would have been good if you could have the mounting holes in a vesa compliant pattern to allow multiple mounting options.

I must be missing something as I don't understand the purpose. When mashing in you can directly look at the graduations to see the volume and pre-boil or during the boil your volume is up around 100L so the sight glass being only up to 80L would be pointless.

Hi @KegLand, do you have something similar as the tapcooler Nanocanner can Holder to fill cans under pressure? I feel my cans are always undercarbonated and I think it's due to the flow restriction with the long length and small diameter line. Cheers!

About to buy a few of these. If you pour 10 back to back drinks, wouldn't that affect carbonation level? Or does this lid act as a co2 agitater?

I just got my series X. What is that grey sticker on the back side? How far must be the backside of kegerator from the wall? I have that cylopeptane sticker on my series X. Is it safe? Any chance of leak? Thank you.

Can't see half of what you're doing as it's off camera. Really confusing. Please fix

Great walk-through! I really don't understand the infatuation with 1.5" TC ports. A 1.5" TC port is overkill for an analog pressure gauge, safety PRV, blow-off pipe, spunding valve, thermowell, sample valve, glycol port, ... The X3 lid is so crowded. A 1.5" TC port is too small for a hop drop. The hop drop should be on an 8" to 3" or 8" to 4" adapter cap. There was plenty of real estate on the X3 lid for the 8" TC main port and four smaller TC ports. Interesting decision to forgo a racking valve. I like that you followed Brewtools lead with the welded lid, 8" TC main lid port, glycol jacket and 2" TC cone port to accept a heating element. With the X4, take a look at the Brewtools F-series lid ports.

Where can I buy in UK?

Thanks a million, My 20 pound cylinder Co2 at a professional medical gas and oxygen provider, hooked up, but does not carbonate only slightly 1/5, regardless of how many times and water temperature, even got another sodastrem Terra ,and nothing, tank went through quality and security control Any Suggestions, will appreciate lots of health good weekend

These look great. Why does it take two hours before it can be used?

Looks like awesome bling! A quick question, If I'm already using a RAPT Fermentation Chamber (and won't add glycol to my setup) , will the extra jacket impact the performance / temp movement much when its within the ferm chamber?

A Brewbuilt X2 model with that side heater TC port would make an excellent all in one brewery/fermenter kit.

They look SWEEEEET! on the 53L version, what's the MAX wort volume..... is it 53L plus headspace? Thanks.

That's bloody beautiful! King of the road! Who do I have kiss? 😘😉😎

Hey @BrewBuilt , for the X4 put a 2" TC on the roof of the tank for dry hopping.

Great vid as usual Kee! Does the new Brewbuilt fit into the rapt fermenter chamber? I’m dying to know. Cheers!

Are these coming to Europe?

Using the growler spout push in fitting, on the website it says to use 10mmID silicone tube. What type of disconeect takes a 10mm ID tube?

How do we get these in NZ?

How's the stainless steel Fermzilla coming along? Will it be to a similar specification of these brewbuilt tanks or will it be targeting a lower price point?