Replacement of a 50-year old shower valve without access to the back wall.
Пікірлер: 24
@everythinghomerepair174710 ай бұрын
That old shower wall is called a “mud wall” it’s much higher quality than anything today.
@henryt9254Ай бұрын
I would use propress instead of Sharkbite especially within enclosed plumbing.
@jimzimmerman5288 Жыл бұрын
Wow! great job.
@tomdale1313 Жыл бұрын
Like a, "Pro"...tanks for sharing
@JTTTTx Жыл бұрын
Why didn’t you buy the Moen repair plate- it fits their faucets perfectly- no hang over on the bottom. Also- if you had to solder in the wall- why didn’t you just solder everything and eliminate the “ Shark Bite fittings?
@Vincerama3 ай бұрын
I was wondering that too. I thought sharkbites for people who don't want to solder, and yet he ended up soldering the short pieces anyway. Those valves are "universal" in that you can screw in fittings (which he did) OR solder pipes into the threaded section... But in the end, he showed how both worked, so a win for us anyway!
@ryanperry9838 Жыл бұрын
Can’t use Sharkbite behind walls,
@dyu999 Жыл бұрын
Good job, it will last for another half century. 😄😄
@Red_Twizzler6 ай бұрын
Not a chance
@robanderson41372 ай бұрын
How many hours on that project? total cost?
@BaconJD420 Жыл бұрын
I don’t understand why use sharkbite when you can solder?
@edshandymantips4862 Жыл бұрын
You are correct. As an amateur my intent was to use shark bites for the job. Afraid of burning the house down :). Then I had to do some soldering. In hindsight I should have soldered everything.
@jg90024 ай бұрын
Can an oscillating tool with a diamond blade be used to cut out an opening in tile or is an angle grinder the best tool to use to do this.
@edshandymantips48624 ай бұрын
I have never tried to cut tile with oscillating saw. I imaging it would work but be very slow. Perhaps someone else will chime in.
@jg90024 ай бұрын
@@edshandymantips4862 that's kinda what I figured. There's not a lot of videos out there demonstrating cutting tile with a multi tool. I just asked because I don't own an angle grinder, but I'm just gonna have to break down and get one. Thanks for the great video.
@dattepo7534Ай бұрын
Grinder is the way to go unless it’s your own home that will take you all day to do
@chrisf9607 Жыл бұрын
I usualy completely remove elbows and replace them because unsoldering one side and soldering another pipe in it when I do it I see the other side of the elbow solder melt so I end up taking the whole elbow off it might be fine but that's what I end up doing
@Red_Twizzler6 ай бұрын
Yea its one of the first things you learn when soldering - always solder both sides of a fitting at the same time
@IH8stpdppl Жыл бұрын
I just can't trust a sharkbite behind a wall. That's asking for it.
@edshandymantips4862 Жыл бұрын
I tend to agree. It is a first floor shower with an unfinished basement below. The owner of the house is 97 and when the house sells it will be torn down so . . .
@IH8stpdppl Жыл бұрын
@Ed's Handyman Tips makes total since in that case. Finished job sure did look nice!
@cj1613 Жыл бұрын
Wow tht is too risky using those fitting"s should have solder it.