Shrink Plastic Strawberry and Blossom Earrings

Check out my favorite shrink plastic supplies in my amazon list (affiliated). If you use my link, I get a small commission which will help me continue making content!
www.amazon.com/shop/amymade
Buy me a cup of "resin" to help me support this channel: ko-fi.com/amymade
Instagram: @emii.alchemii
Tiktok: @amy_made
[e-mail]
My Shop: www.emiialchemii.com
Music: Daystat- Plum Flavored Candy
• ✨샛별 - 자두맛사탕✨(Royalty F...

[@janesinger9410]

These are ADORABLE

[@kellystorm6760]

Oh my goddess, these are adorable sweetie. I'm in love ❤️

[@Kimshi4242]

So cute!

[@mellylo]

So cute❤

[@trishajanecreates]

Always soooo cute 🥰

[@hippiesister100]

Love!

[@DoItCraftyYouTube]

Very nice ❤❤❤

[@EternalSnoie]

Is sealer spray needed or can just skip to uv resin?

[@bigdreamer02]

May I ask which heat gun machine you use?

[@wyndomhaus]

What cricut settings did you use for the cut outs?

[@roopalatha3659]

Hi can u plz say ..What are the options for coloring shrink plastic??

[@JoCFrie]

I have several shaker mold, how do I make the acetate shapes to fit? Thank you for any advice!

[@MileyonDisney]

.•♫•♬• 𝐓𝐡𝐨𝐬𝐞 𝐚𝐫𝐞 𝐩𝐫𝐞𝐭𝐭𝐲. •♬•♫•.

[@Villagenanny]

I LOVE THIS!!! ❤ 😍 What measurement did you use for Cricut cutouts?

[@MoonlightSlimer]

@@AmyMade Oh...in the video it says you used the cricut to cut the shapes out. What did you use?

[@AmyMade]

My bad I did use a cricut. For some reason this comment kept showing up on my other video in my KZbin studio. I think anything from 1.25 to 1.5 inch would be a good start

[@AmyMade]

@@MoonlightSlimer my My mistake, check my comment below!

[@candacesmith3580]

Did you apply sealer to both sides, or just the top side which had the Posca pens?

[@AmyMade]

Both sides since I used soft pastel on the other side

[@evelinaz1548]

Do you coat the sides as well with resin or just front and back?

[@AmyMade]

I don’t coat the sides

[@TalasiaD]

Hi there, may I ask what you are using to heat the charms on? It looks like cork board and parchment paper, but what is the mesh thing?

[@AmyMade]

The mesh thing is a silicone baking sheet I cut to size

[@TalasiaD]

@@AmyMade Thank you! 😊

[@jessicanefrain]

Are there any replacements for UV resin I can use??

[@AmyMade]

You can use 2part resin

[@lifewithartcraft3433]

What kind of plastic you have used?

[@ame-kc1si]

Polystyrene/No. 6 plastic/shrinky dinks

[@breadstixxxx]

there’s already so much plastic waste tho :((

[@emmaslug]

What kind of earring backing are you using? :0

[@AmyMade]

They’re clear silicone ones

[@emmaslug]

@@AmyMade how does the plastic connect to the backings? Is there like a hoop under it so the strawberries can loop in? Thank you!!

[@AmyMade]

@@emmaslug ooohh you’re talking about the earring post finding. Yes I used ones with a loop attached

[@emmaslug]

@@AmyMade I’m sorry I have so many questions 😅 How did you attach the flower? Because the posts I’ve been using have a thing there? Did you put it in the middle of the flower? How did you stop the flower from sliding off??

[@AmyMade]

I used glue to attach the flowers to the finding

[@jamijeanette1813]

Is that Shrinky Dinks paper?? 🤔

[@AmyMade]

Yes ! Shrink plastic, shrinks dinks are the same thing

[@GopherCakeStuff]

Gorgoeud