Best Jack of ALL TIME - Harbor Freight DAYTONA LOW PROFILE LONG REACH JACK - Why It’s My Choice

[@twc9000]

I bought this jack after seeing your review. The deciding factor was the foot pump. The smaller lifting pad is a good feature, also. Thanks for pointing that out.

[@Trigger_32]

Just bought one, right out of the box I put it under the dually rear of my Ford T350HD service truck with a Knapheide utility body, which currently weighs in at about 9,000 lbs... it got the whole rear off the ground enough for me to rotate the tires and install valve stem extensions... First impression is great!

[@f.b.i7334]

Does it still work?

[@mrbreezeet1]

How is that Jack holding up I was deciding between this and the one with the 3-year warranty

[@Trigger_32]

@@f.b.i7334 it does

[@Trigger_32]

@@mrbreezeet1 still working good

[@mrbreezeet1]

@@Trigger_32 👍 thanks, good to know.! Practice safe work habits.

[@oshtheld]

Thanks video you man, you sold me on this floor jack! I would also just like to say I appreciate the video quality and camera work that went into this review!

[@MotorsportCreative]

1:30 usually the nut comes first and then I slide it out, but to each their own

[@jacknguyen3233]

Make sure you give it a pull

[@YungSteambuns]

Knuckleheads LMAO

[@tggraham3321]

I gotta say.. this is THE best review I've seen for not just a jack but just about most you tube reviews.

[@rbilardo47]

You sold me on this jack son. I just ordered from one Harbor Freight because of your review. Thanks. I have a BMW 128i convertible and this should work perfectly, can't wait to receive it.

[@yahuahyahusha364]

I almost turned the video off after you popped out with flops on 😂🤣😂 Glad I watched, going to try to pick one of these up 👍

[@45eno]

Thanks for the great review and quality production. I just bought the Yellow Daytona yesterday as I noticed it doesn't sit any higher than the LP Long reach model. I had two main areas I was hoping it would do well. 1.) 2008 Miata Sport, I wanted to be able to reach the front jack point and since both the Yellow or Orange Long Reach are the same height I found the longer reach ended up not even being needed as the yellow model slide under the car just as easily as the long reach. 2.) RAV4 Gen 3. I wanted a jack that could raise it up high enough to slide some wheel ramps under it so I could quickly and easily set the entire vehicle up on 4 ramps. I still need to test this as I did measure it and it is close. The long reach might be needed with that extra 1" of lift. I do agree with you the smaller jack pad would work better for me as well with a Miata, Sienna and Rav4. My hockey puck allows for a more pinpoint jack location though so not a big deal. Too bad we can't buy alternate jack pads either small or large from HF. So I think I will likely keep the yellow model as it is just as low as the long reach so I didn't end up even needing that extra reach for that deep jack point on my Miata. I like the 3yr warranty and zerk fittings all over to properly grease it even though I don't need that level of durability as I don't use the jack all that often. Also there was $20 off the Yellow model that made it cheaper by $10 than the long reach. The only main feature I might like is the extra 1" lift and foot lift.

[@quoc-baovu8241]

Thanks so much for your detailed review; I was also debating on the long reach or not but your review has convinced my to go with the long reach because I do have a '01 CLK430 that would benefit from this longer arm to reach the engine lift point near the front axle. Like you I usually need to lift one side up first then get to that lift point with the jack. Thanks a lot again for your great review I really like it very informative & useful. Cheers,

[@zaineridling]

15:00 In fluid dynamics, the presence of air in the fluid creates the exaggerated or erratic actuator movement you experienced where too much (hydraulic in this case) fluid has the same effect as too little. Every system has a "just right" point, whether it's your washing machine or your toilet tank or brake lines.

[@flashcraft]

Great video, Skip. Your reasons for selecting this jack over the "Yellow" one were my own as well. I like how you demonstrated adding the oil and playing around with it. You are very clear with your explanations. I really appreciate that. One small suggestion, if I may? You might want to lose the loud music that plays for about 10 seconds starting at 6:21. No good. Sorry. By the way, did you get the extended warranty? If so, how much did you pay for how long a warranty? Excellent video review and demonstration. Thanks for putting this up.

[@GarageDynamics]

Hello Anonymous! Thank you for the kind words. Hahahha It's a reference from Epic Rap Battles Of History. It's cheesy I know, but I like adding some cheese to my videos from time to time :) Cheers brother!

[@alexanderquilty5705]

Yes it was a reference for us youngins lol.

[@elliottp.8340]

Wow this is amazing, perfect review! I am actually buying this jack for my S-Class so I'm glad to hear it works good!

[@ocesmekanics3831]

That's it! I'm buying one of these just for the high lifting point. That's amazing

[@aleexx933]

Great video! Only complaint is the large volume range. My constant adjusting was a distraction from the quality of video this is!

[@gopaulsalick507]

I personally bought this jack 4 months ago after comparing it to the yellow one, the pistons are the same size welds are the same. The only difference is the saddle and saddle mount are smaller and the front wheels dont have zerks fittings to take grease, and the handle on the yellow jack has a quick release pull pin

[@topgunns1000]

Both of my yellow Daytonas do that saddle pump thing. I was going to exchange it, but all the ones on display do it too. Therefore, I've concluded it's normal and don't care anymore LoL! excellent editing! *update* I'm only adding this because of the notification i got about my original post which brought me back here. Here goes... the gondola over my porch has a rotting main post holding it up. I used my yellow Daytonas to jack up other wooden posts to support the structure while i replace the rotten post. The jacks have been holding it up for about 4 days now. No leak down.

[@GarageDynamics]

Thanks Topgunns1000! Also, thanks for sharing that information with everyone. I was able to reduce the saddle pump to almost zero. It comes down to getting the fluid level just right. Cheers!

[@vitoscatigno4207]

If you own a Mercedes S500 you don't need a floor jack you need a bank account and a Mercedes Dealer!

[@michalmarzec3652]

LOL! You couldn't be more right about that!...

[@tggraham3321]

I disagree. Just because you have a relatively expensive car doesnt mean you should forget about doing you own maintenance. It's one way of affording the car in the first place. This comment is spoken like a true poor person. Ijs...

[@mustangdemon87]

Or a mechanic like me that owns a top of the line diagnostics computer and does side work... Lol

[@mustangdemon87]

@@tggraham3321 moreso by said by most people because people think the dealers know best. This is not reality. Dealer techs are only trained on one vehicle and what they commonly have issues with. If you find yourself a tech like myself that has the tools and does side work or simply a german car shop not dealer they typically cost half the price of dealership use the same parts and have better training.

[@andybub45]

@@mustangdemon87 better training? I dont know about that. Most manufacturers now partner with tech schools to bring manufacturer specific training into the schools automotive program. Plus, dealers have access to specialty information syetems and all sorts of manufacturer data that independent mechanics cant touch.

[@ask4george1]

I saw that jack at Harbor Freight, I was going to buy it for the same reasons as you. I went to pick up the box and noticed that it was very heavy. I thought it's too big and heavy, I don't have anywhere to store it, having a single car garage. The thing is that I noticed in your video, is that the handle comes off very easy, which would allow me to store it. I think I will go back and buy it.

[@GarageDynamics]

Hi George Cicairos, That sounds like a great idea! Have you also thought about placing the jack in the center of your garage at the end, so that when you park your car the jack would sit under your bumper? You would just have to be careful not to hit it or run over it haha!

[@AZDESERT2024]

Bring it inside and put it Under the bed.

[@TooloxAlfa]

yes, and you can also wake up your wife by lifting one side of the bed

[@bigbaddaddio]

Excellent job on this review! I hope our buddy at Project Farm gets a look at it and offers his thoughts!

[@IDADDYIproductions]

Really informative review! Thank you so much for taking the time to make this video. 👍🏼

[@constantauctions]

Here is another car jack review kzbin.info/www/bejne/aGqQnISGfNZ_l80

[@cardo1111]

a well done and very comprehensive review, nice jack I like the foot pedal option looks like a very useful feature in tight quarters.

[@GlynRobinson]

Looking at buying one. I wish the lift plate was a little bigger round for my application. Nice video! thanks.

[@cuttingedgecool7235]

Excellent review and demonstration! The Daytona 3 Ton Long Reach jack is definitely the way to go!

[@GarageDynamics]

Cutting Edge Cool, I totally agree!

[@TheBigpoppa54]

"NOTE: The fins on the sides of the Daytona, reinforce the frame and gives it more STRENGTH" ...................Nuff said.

[@cardo1111]

This is the best Daytona jack, now offered in more colors. Excellent review and editing 👍🏽

[@davidjunior5773]

Can you show a detailed video on how to bleed and add the hydro fluid thx… great video👍🏼

[@GarageDynamics]

Hello David Junior, Thanks for the kind words. Sure! I'll add it to the queue!

[@MattSeals]

Thanks for the purpose of furnishing many of these fantastic information.

[@GarageDynamics]

Hello Matt Seals! You're welcome! It's my pleasure!

[@Mach141]

Decided to compare this to its $60 cheaper, non long reach brother, thinking i could care less about the foot pedal and an extra inch of reach for $60 price premium. I was quite surprised to see they are completely different jacks, in height, lifting height, length (like 4.5 inches longer) and most shocking...weight. This beast weighs a solid 25lbs more than the low profile standard reach brother. The smaller, lighter version should meet my needs, its actually not nearly as tall and the lifting height is a bit lower, so it also has advantages besides being much less expensive. Nice review!

[@thelegendaryredx7710]

Got one in blue myself! It’s great especially for lowered cars

[@GarageDynamics]

Hey The legendary Red X! Blue is such a nice color. I agree, it's really good for lowered cars. Enjoy your new jack!

[@7s29]

Same here, blue.

[@khalmaj4547]

Good review. Got to get one of those SKIP ART PICTURES ...all things automotive T shirts

[@GarageDynamics]

Thanks Khal Maj! I'm Working on it! :) Cheers!

[@10mmfan]

Great review. Already bought one but I’ve learned a lot here. I feel even better about my purchase.

[@GNX157]

Not saying it will change the performance in any great way, but on the craftsman (I have that exact one), check and fill the fluid if low. Mine was a bit low and it improved performance after I corrected the level.

[@GarageDynamics]

Thanks for the advice GNX157!

[@coryw.5755]

Thanks for the great video. Just picked mine up today after watching.

[@anonymousgoat3669]

Harbor freight has the floor jack game on lock! 👍

[@7s29]

I have this jack in blue, same design, different manufacturer. This jack works a treat, just what the Dr ordered.

[@cyprianskiba8768]

First one out of the box was wobbly with one front wheel not touching the ground. Returned it. Decided to inspect the replacement in the store. Second one out of the box was worse. The front wheel retainer clip fell off pulling the jack out of the box and was wobbly as well, one wheel not touching the ground. I asked for a refund and gave up on the jack.

[@saltysteel3996]

The Daytona Super Duty is the SnapOn jack. Same manufacturer, same factory, same assembly line, same jack. Only jack with the 3 year warranty. This long reach is only 1 inch longer in length from pivot to saddle, and goes about 3/4 of an inch taller and about 1/2 inch shorter. The Super Duty is worth the extra 40 dollars over this Long Reach version. Plus I found the foot pedal to be a useless feature that's just in the way. Edit: Personally, I mostly work on trucks, SUVs, and tractors and the larger saddle pad on the Super Duty jack is a much better feature. Also, the Daytona Super Duty jack reaches full height in only 4-1/2 full stroke pumps.

[@GarageDynamics]

Hello Salty Steel! I guess it's time to add the Super Duty to the collection haha!

[@bruceaugustine6486]

I am thinking there was a little bit of air in the jack

[@GarageDynamics]

Hi Bruce Augustine, I think so too. It works like a dream now

[@CKChoong]

would this be a good gift for a father who likes to work on cars at an amateur level?

[@GarageDynamics]

Hi Cynthia Choong! Yes, this would be a great gift for your father. As he gains more experience he'll be glad you bought this jack for him. I hope this helps. Cheers!

[@CKChoong]

@@GarageDynamicsSkipArtPictures thank you for the informative video!

[@GarageDynamics]

@@CKChoong Anytime! Thanks for stopping by :)

[@itsmeatiq]

@@CKChoong if you didn't buy it yet, I would suggest you to buy the one with low profile only. It will be lot cheaper and lighter ($119 using coupon). You can live without the long reach option.

[@V8SKULLS]

Yes, indeed, im a dad who works on all vehicles, and have many of jack of my life, and just picked up this one in green. Damn i should have bought this yrs ago. Got it on black Friday deal ffg or $179.00 , i must say compare to my craftsmans jack this one is rock solid and strong, works great on my F350, F150, and my Ford ranger edge.

[@vr-cx6lq]

i got tired of the jack and stands so i bought a quickjack 7000ext all four tires off the ground and feel way safer and a lot more comfortable under my vehicle in my opinion it was well worth the investment great in depth review sir on the daytona

[@GarageDynamics]

Hi V R, That's cool! How convenient is it to store it?

[@vr-cx6lq]

@@GarageDynamics my son built me a set of brackets that i could mount them horizontally on the wall at each side of my garage i wish i was able to figure out how to add a pic here they arent hard to store great investment

[@GarageDynamics]

@@vr-cx6lq That's very kind of your son. I took at look at the quickjack and it looks like a good tool to have

[@vr-cx6lq]

@@GarageDynamics i've been watching your videos for sometime the 722.6 transmission fluid change tutorial i found quite helpful for my sons ml320. the quickjack worked great for me in my low ceiling garage for working on my cars and i move it out to the driveway when working on my ml320 and it lifts my 2014 ram 1500 with ease. i was reluctant at first to spend the money but i definitely have no regrets since buying it last year

[@GarageDynamics]

@@vr-cx6lq Thank you V R! I appreciate the loyalty :) Wow, this jack just keeps getting better! Haha! Are you using the jack on a flat or angled driveway?

[@MartinsGarage97]

I bought this jack for my Excursion. 4 ton veichle loaded. So easily lifts half of my truck. Obviously I put 6 ton jack stands under neath before I work underneath a car

[@GarageDynamics]

Nice Nick and Ford's!! I'm glad to hear everything worked out for you!

[@OU812NVME]

That long reach has a foot pedal in the back and you pump that up to get the height of the Jack there faster and then you use the Jack handle

[@jtwu8931]

Love the force field safety shoes 👍

[@amr-50]

Thanks for your video i have a very important question were you able to carry it into your truck ? Or is it too heavy for one person to carry , i am asking because i gonna carry it in and out of my truck and i need to know your experience on that

[@GarageDynamics]

Hello Amr Ali! It's very heavy. If you are going to carry it in your truck maybe once or twice then its ok, but if you will be lifting it in and out of your truck every day I would recommend getting an aluminum jack. I hope this helps. Cheers!

[@lakesidedreaming]

Epic jack battles of history! 😂 sometimes i do the voice from that and im misunderstood😂

[@tonyrowe1455]

How has it held up over time? How much have you actually used it? Do you know if there is a difference between the orange and the blue?

[@peterbenjamin8351]

Hahaha the smoky intro was great.

[@mrmidnight32]

Hey man, what is the length from tip to the up bend above the “T”? Then what is the length and height above the “A”? I have a lowered turbo track 350z I lift from the front but with a normal jack I need to drive up 2 2x4’s before I can get under it. I’m trying to see if this will reach before it hits my bumper and allow me not to have to drive up onto blocks every time. Shit gets annoying lol

[@yenb86]

Incredible review on something as simple as a floor jack. I'm buying it. Congrats.

[@wyattandwill12]

Great video thank you! I'm wanting to pull the engine/transmission/suspension out from the bottom of my car and it's looking like I may be able to with that jack if I can find a way to hold the body up or I may roll the assembly out the side (I have a pallet with wheels I can use if clearance allows). I ordered it with 15% off so around $170, plus shipping and I also got the Pittsburgh 25" breaker bar with a comfort grip for $15.

[@ericgarcia1632]

I bought this same jack but exchanged it for the yellow super duty because the wheel are held together with only some cheap clips and rivets on back wheels were cracked. The yellow one has nuts to hold better. Just taught that was its weakest point of the jack. Other than that. Both jacks work great. Only 10$ difference

[@BSed31]

Thanks for the review. I was between this and the yellow. I just got this for 159.99 which is a pretty good deal. Skipped the warranty, the reviews on these are too good and I use a jack less than 8 times a year usually. Am using them to lift a 340i (3700 lbs) and a Jetta (3200 lbs), so the orange is more than enough. I do need 2 jacks and have an old craftsman that's pretty worn out. Thinking I'll get the yellow next year around the holidays as it was on sale this year. Hopefully that'll mean two jacks that outlast me with the proper care. Thanks again for the thorough review.

[@howtodoelectrical200]

Thank you

[@precisiont5188]

Can you please provide the link or complete name?

[@GarageDynamics]

Hello PrecisionT, Here is the link. I also have more links in the video description in case you're interested. Cheers! Daytona 3 ton Long Reach Low Profile Steel Heavy Duty Floor Jack: amzn.to/3FW83cM

[@LuisChavez-lr7ro]

Damn now I don’t know which floor jack to get, this one or the yellow professional one?

[@Rhosticks]

This one sits a little lower, goes a little higher and goes a little deeper than the yellow one. Depending what you want to do with it or what you're working on. They both handle the same weight. I got the yellow one when it just came out and it's still going strong. I have zero issues with it.

[@Rhosticks]

I'm really liking this new one because of the foot lift option and the added reach. Visit the store and look at them on the shelf. They have them assembled and on display.

[@BenJamonGaming]

the yellow one is literally the same jack as snap ons. literally same factory. snap on actually sued them over it but lost since the manufacturer sold it to both of them. the new daytonas seem to be just riding on the curtails of the yellow one. the yellow one has been proven, the orange have not.

[@dizzy4303]

Ben Ault are they still made in the same factory as fap off? Or have they moved to cheaper manufacturing since the fame they got from the lawsuit?

[@ronlind1757]

Yellow Professional is a better jack.. imo. Pump internals are better. 3 yr warranty as well

[@fh1980ram]

Uny updates after two years.?

[@GarageDynamics]

Hi Fred! I can't believe it's been two years already! The jack is still going strong. No leaks, no strange noises. Still lifts cars super fast and I haven't noticed a drop in max height. The Daytona Jack is a really good investment.

[@thalegacy6]

Harbor freight, here I come! To hell with distancing!

[@FuttBuckerByMutt]

You can order online...

[@chrispyfer7721]

You can also pick one up at the store.

[@waimeaguyz9074]

I think I'm buying the Daytona jack. Thanks for the video.

[@vikingnorm6935]

I have the Daytona 3 ton low profile rapid pump but not the extended reach, it’s DEFINITELY worth the $ I paid, I would pay $200 for this jack, honestly, it’s that nice, I had a $119.99 coupon & used 20% off coupon & STOLE THIS THING!!!! I might get an extended reach also someday, never have too many tools!!!

[@MiguelGarcia-nl3ci]

as long as it could flip my car after getting the P0420 code

[@miahmarieeeeee]

Catalyc converter below thereshold efficiency

[@MiguelGarcia-nl3ci]

@@miahmarieeeeee yes. Cats are expensive

[@MrAlternation]

Great video!

[@scottphillips2420]

very good review,and even show how to service it;-)what was the lowest price?

[@GarageDynamics]

The prices changes from time to time whenever they're on sale. Subscribe to the catalogues for the best prices. I hope this helps. Cheers!

[@victorsanchez1983]

I got mine for 217 well worth it Can’t use any coupons for this 😤

[@samspace81]

You have a soothing voice.

[@kazper2011]

I really wanted one of these until I found out that that it only has a 90 day warranty. For almost 200, I would want more assurance.

[@45eno]

I was told at HF that they carry 1yr on these LR LP models and 3yr on Pro Yellow model. I bought the Yellow.

[@rozzijet]

$60 for 2yr warranty

[@t.l.robinson2162]

Excellent jack. I have 6.

[@GarageDynamics]

Hello T.L. Robinson, Wow that's awesome!!

[@Mr.Thermistor7228]

Great information 🤟🏽

[@Mecambrea77]

The only thing I don’t like is that being a new jack isn’t supposed to come ready with the right amount of oil?

[@adventureescape1929]

I got the same jack. Display model for $135

[@GarageDynamics]

Hi Adventure Escape! That's awesome! I didn't know you could buy display models. Cheers!

[@joshuaanderson8869]

My harbor frieght sucks. They wont sell display items

[@misterrightfix4129]

Good review! Thank you so much!

[@TJ-hd5ym]

Check the oil they come low sometimes

[@GarageDynamics]

That's great advice T J! Here is a link on how to change the jack oil. kzbin.info/www/bejne/nJjYeaGIfLt8a6s

[@supremeautomotive6749]

I have the yellow and just bought the same one you have but now they have it in green so I bought it. The yellow is better in alot of ways has more grease fittings and size is not that different I will do a video

[@GarageDynamics]

Hello Attention 2 Detail Automotive Towing And Detailing! Yes, I think for your needs the Yellow Jack is better. I noticed that they come in Green and Black now. That's so cool! I might have to buy another one as well haha! I'll be looking forward to seeing your video! Cheers!

[@supremeautomotive6749]

@@GarageDynamics I did a video

[@sirsweetness8332]

I have the yellow professional and I love it.

[@sticksandstuns]

I have the yellow one and it's way better quality

[@eguitarplayer6689]

I have the same jack with green coloring. I have had no problems and don't expect any. A lot of cars are so low that you need the confidence of a low profile/long reach. I still employ jack stands or a bottle jack (as backup) in case I accidentally move/release the Daytona. The steel model is heavy but rugged. Maybe one day Harbor Freight will figure out a way to add handles for mobility.

[@joev8275]

Is it hard to find the jack’s release point to slowly drop the vehicle? My last jack dropped incredibly fast...

[@dannyhernandez5184]

Thanks Brother 🤟🙏🙏🙏

[@tomasgimenez4592]

Great. I neede something that will fit under my Bentley

[@GarageDynamics]

Hello Tomas Gimenez, Yes! This jack has you covered! 😁

[@TheEclecticHandyman]

Excellent review! 👍👍

[@p3rformanc3fanatic60]

Weld your custom handles to it!! You could get it done easy with a cheapo flux core welder as long as the settings are set correctly.

[@mrbreezeet1]

How is this Jack holding up for everyone? I am torn between this Jack and the professional one with a 3-year warranty. Harbor freight should put a 3-year warranty on all of these Jacks I think Menards is giving a 3-year warranty on all of their jacks.

[@GarageDynamics]

Hello anthony diodati! I use this jack a lot and it's holding up fine. It's a tank!

[@jx83xparten6]

Best review from a grown ass man that wears flip flops with pants on a vid. lmfao!

[@jnal21]

I just bought one of these but it doesn't have a foot pedal like yours does. Are there different versions?

[@flipmode00]

yes there is, just got the long reach low profile 3 ton today and there's a foot pedal

[@sheepdogsherlock1311]

@@flipmode00 hard for me to justify 60 extra dollars for a foot pedal

[@flipmode00]

@@sheepdogsherlock1311 I totally understand your point but in my situation I wanted cuz it's the long reach and I could lift the car from the middle and I was looking at the arcan Xl2T but this was 199 versus 226.

[@stephencannon3140]

I have this jack and works great. They also sell a cross bar adapter that allows you to make a T and for small/compact vehicles you can raise both axles at the same time. Makes it easier to do brake work. The only drawback is sometimes the lifting point and jack stand point are the same. Have to find a designated spot for jack stands. For brake and suspension work you can remove a tire and set the Jack Stand on the control arm. Flip flops in a work shop environment aside he does have a point about not using to support. That’s what jack stands are for.

[@DeathByLego]

How is it doing a year later?.?

[@GarageDynamics]

Hello Death By Lego! It's still working great!

[@DeathByLego]

SkipArtPictures I might have to get this for my 74 vette!

[@hondahaney6404]

How high does it raise?

[@mrblister95]

Nice job!

[@itsmeatiq]

Can I use brake fluid?

[@thinshavings]

Fip flops in the garage???

[@heavychevy383]

good review, but im diggin on the vintage F1 poster behind ya man!

[@GarageDynamics]

Thanks Heacychevy383! It's always good to hear from another F1 Fan :)

[@jondorman9111]

Are you able to jack up a car and or truck fully just using the foot pedal and if you can is it easy or will the will the pedal snap off? i work in tight places daily with a floor jack where i can only get about 1/4 of a pump

[@dennisyildirim2708]

can you work under that ? Is it safe to use it while working under it? Or do we need separate fixed metal jack constructions to put underneath to stabilize the car?

[@rayzracing]

Dennis Yildirim use proper jack stands better safe than sorry

[@irineoesguerra9374]

Where in the Philippines i can buy?

[@narcissistinjurygiver2932]

nice jacks. their pitsburg flex head ratchets are awesome, better than so

[@GarageDynamics]

Hi Dann Hienn! I've been looking at their Pittsburgh flex head ratchets for a while. I'm waiting for a flex head quick release with plastic grip version to come out. Hopefully Harbor Freight delivers on this one

[@narcissistinjurygiver2932]

@@GarageDynamics get one. they are way worth it

[@GarageDynamics]

@@narcissistinjurygiver2932 Will do! Cheers!

[@slidewayskenny6925]

good video brotha

[@mrbreezeet1]

I wish the warranty was better on this Jack I am just not comfortable with a 90-day warranty

[@CORZER0]

Have the same one. Love it.

[@constantauctions]

Here is another car jack review kzbin.info/www/bejne/aGqQnISGfNZ_l80

[@X文-v3z]

This one good for s2000?

[@miguelsalazar3239]

Many still don't know what the foot pump is for. And it's not to lift vehicles at all.

[@jakekennedydrums7868]

Good video man! Use one of these at work all the time and wanna grab one for the house.

[@constantauctions]

Here is another car jack review kzbin.info/www/bejne/aGqQnISGfNZ_l80

[@jon2229]

You just scared the crap out of me, you can replace an engine with that Daytona

[@rkgsd]

It's made in the same factory the Snap-On jacks

[@michaelscarn2660]

Loser

[@codyhayes5499]

Mad bro?

[@jeffward6166]

Not this one, only the yellow HD one

[@deangeorge5706]

I bought one.Overkill for my needs,but Ilike it.