Small End grain Bowl: practice

[@DancingFox6]

Between you and Richard and Tomislav, everything I ever thought I knew about bowl gouges and spindle gouges is out the window and I’m much freer in how I use them. I have to add that I’m using scrapers a lot more too. Great instruction. Thank you.

[@WYOMINGWOODTURNER]

Thanks very much. I appreciate that. I’ve been turning a long time and I still learn stuff. 👍

[@SuperBowser87]

When you cracked it open a little tear fell from my eye! Great job Sam.

[@WYOMINGWOODTURNER]

Tom I did that once in a middle school shop class demo....Oh man the kids went wild. Why would you do that???? You could have given it to me, they all said. Thanks for watching

[@markyehle6355]

Sam---great teaching tutorial. After 48 years in education I know a good teacher when I see one. As an administrator I always used coaching as an example for classroom teachers because they explain the “who, what, why, where, when, and especially how”. Following that with demonstrations for the students completes the job. I have no doubt that you are/were a good teacher. I learn and improve my woodturning with each of your videos. Thanks.Sam---great teaching tutorial. After 48 years in education I know a good teacher when I see one. As an administrator I always used coaches as an example for classroom teachers because they explain the who, what, why, where, when, and especially how. Following that with demonstrations for the students. I have not doubt that you were a good teacherSam---great teaching tutorial. After 48 years in education I know a good teacher when I see one. As an administrator I always used coaches as an example for classroom teachers because they explain the who, what, why, where, when, and especially how. Following that with demonstrations for the students. I have not doubt that you were a good teacherSam---great teaching tutorial. After 48 years in education I know a good teacher when I see one. As an administrator I always used coaches as an example for classroom teachers because they explain the who, what, why, where, when, and especially how. Following that with demonstrations for the students. I have not doubt that you were a good teacher

[@traceysmith1456]

Without doubt, the most useful video I’ve seen so far. As a total beginner this has answered so many questions. Thank you.

[@JOHNSmith-pn6fj]

Thank you. I was just trying to make a small bowl like that and just could not figure out how to make those cuts. I didn't even think of trying a cut like that. That is going to help me a lot in those situations.

[@dickydebuilder]

Your practical advice is really useful, thanks.

[@wrongtown]

The zoomed in shots had me leaning forwards in anticipation, well played mate 😅

[@WYOMINGWOODTURNER]

Glad you enjoyed Sam

[@DroweHP]

Hi Sam! You are an admirable instructor! It gives new hope to succeed with a turning piece. All of these tips also gives a sense of why it is so hard to do well in the beginning. Hanne

[@WithTheGrain527]

:D great video Sam. I was on the edge of my seat waiting for an explosion!

[@raymondbissonette1912]

Excellent tutorial. One suggestion - identify tool used for finishing outside surface. Appears to be the bowl gouge.

[@WYOMINGWOODTURNER]

Actually that is an old spindle gouge-I no longer have. Sam

[@MikeWaldt]

Brilliant demonstration Sam, great practice piece. Cheers Mike

[@effeinc]

Thanks. Videos like this lifts my confidence level to the point where I think I can do this. Mike

[@jasonhaff9757]

this was great, thank you. The bowl crack made me laugh quite hard.

[@davidnoyce7531]

Great demo, Sam. Your explanations of every step of the job is very instructive. Always enjoy your videos. Great work, David

[@judytad1]

I really like your video. You have shared an amazing number of tips on how to resolve different issues. I'm fairly new to wood turning and have just got my first lathe. This sort of project is ideal for me especially as I don't have the members of the club I go to, to ask. There's nothing like figuring things out for yourself and taking the time to learn from others like you. Thank you, Judy UK

[@dustycornerscalgary2208]

Thanks for the tip on the jam chuck fit

[@yveshetu8026]

I am a beginner and your videos really help me. I have some maple and this little bowl will be a good practice for me. Thank you. I would be interested to see how you sharpen the kelton hollowing tool that yous used in a video about hollowing.

[@jolox.]

This is really helpful. Thanks for posting!

[@alansimpson596]

Many thanks for an interesting video and for adding to my knowledge. Best wishes, Alan.

[@kreech68]

Great WET tissue paper idea!! A bit of "expansion" and a bit of "glue-ing" - cool!! I would envision this as a "salt pig" - what other use might you use this for ?!?! (ah - a 10 year old video - I don't expect an answer !!)

[@WYOMINGWOODTURNER]

No, I’m right here, honestly, I can’t remember the video that you’re watching and not sure what a salt pig would be 🤣

[@WYOMINGWOODTURNER]

You make an excellent observation. Nothing worth anything is meant to be easy. Keep at it. Sam

[@WYOMINGWOODTURNER]

I wasn't sure if I would cause "talk" with cracking that little bowl. It reveals a lot when you do that. It is always a surprise. Sam

[@Jeff1Jeff2Jeff3Jeff]

Thanks Sam, another entertaining, and informative video .. Make 'em and Break 'em! 8-)

[@WYOMINGWOODTURNER]

I can remember if I covered sharpening the tool. The best way is to use a slip stone and make a pass on the front of the cutter upwards that helps form a burr. You can do the same on a grinder but takes off a lot of steel. Sam

[@markb8954]

Nice clearly presented info. Thanks

[@JimmiePorterAtStuartArts]

Thanks for the tutorial on this. I'm still intimidated by end turning and this gives me confidence.

[@jeffoldham3466]

im new at bowl turning and have had some bad experiences,,can you tell me what tools you were using and the speed at which you hollowed out the bowl

[@vc01928]

Great idea Sam, thanks

[@WYOMINGWOODTURNER]

Thanks that means a lot for you to say that. Sam

[@joanbusby3213]

I love your videos. You have inspired me to go from pen turning to small bowls. Can you tell me what size bowl gouge is best for small bowls.

[@WYOMINGWOODTURNER]

Joan Busby I am glad you are fired up. In the video I am using a gouge that is 3/8" in diameter. (I like to know exactly what the diameter is - this tells me more). The wings are really swept back on this gouge. It is pretty much dedicated to one task---removing wood from a small bowl or end grain project. One of the issues is that it is difficult to use a push cut with the bevel rubbing. So even with a gouge, you are scraping. I may even use an actual scraper if I don't have to remove much wood. Sometimes it comes down to what tools you have at hand-even a spindle gouge would work. Sam

[@zachomega187]

Why center to rim and not rim to center? I've seen both with no explanation as to why. thanks!

[@WYOMINGWOODTURNER]

At 4 minutes and 11 seconds into the video I mention why I am cutting from the center TO the rim. I said, "I am trying to cut across the grain" There is no ideal way to hollow out end grain as you do in a small box. The best you can do is cut across the grain, not into it. Sam

[@JSEquineVideos]

Sam, I've learned so much since subscribing to your channel! I'm a novice turner, could you please explain how you use the skew between 1:07 and 1:13 to true off the face? I couldn't figure out the technique looking at the video (and it looks scary but very efficient!). Thanks (Jamie)

[@WYOMINGWOODTURNER]

+JSEquineVideos Not too scary. I have the skew chisel flat on the rest. I have the toe or long point to my left or against the wood. It is just a peeling cut much like you would do with a parting tool. It is a cut with the edge just below the surface but I only have 1/8 inch of the tool into the wood. Sam

[@JSEquineVideos]

Thanks for explaining! I need that technique in my arsenal.

[@bigguix]

nooooooooo ! RIP little bowl who gave his life for science !

[@Shawwoodturning]

Sam I am new turning. I have been working with some cedar but I keep getting torn what am I doing work

[@WYOMINGWOODTURNER]

Archie, your sentence is a little broken up but I think you're asking about torn grain. I think to begin with, party your problem is using Cedar which can be a little bit soft and difficult to turn. The best way to eliminate torn grain is to have a good sharp cutting tool. And by that I mean either a spindle gouge or a bowl gouge. It would help to know what tool you are using. And finally, sanding will not get you out of trouble after you have created touring grain, only cutting Will with the sharp tool thanks Sam

[@WYOMINGWOODTURNER]

Thanks Mike

[@WYOMINGWOODTURNER]

Thanks Sam

[@rafaelramos1486]

The sanding trick awsome

[@WYOMINGWOODTURNER]

Exactly, Science....I like that Sam

[@quintoflyer]

I notice you turn off centre (tool high) instead of centre line , what difference does it make

[@WYOMINGWOODTURNER]

Are you talking about the inside or the outside of the bowl? On the inside of the bowl, you have to be at least a little above center to avoid a catch. Also which tool was I using?

[@billy19461]

I cried when you broke that pretty little bowl.

[@WYOMINGWOODTURNER]

It is good for the ego....

[@errollesassier9084]

how long have you been turning

[@WYOMINGWOODTURNER]

I started in 1988-but dod not turn too much at first. I have turned very seriously for 20 years. Sam

[@jimbeaver27]

Always these special tools. I just want to see how to make this bowl with normal tools.

[@WYOMINGWOODTURNER]

Jim I started out with a bowl gouge with really long swept back wings. You could also just use a regular bowl gouge or even a spindle gouge. Each of us must discover what tools are normal for us. Sam

[@imapseudonym1403]

You say you don't want to put your head down, why is that? For me, it's the only way I can see what the heck I'm doing!

[@WYOMINGWOODTURNER]

This is an important aspect of hollowing. And even in this little bowl, I am hollowing. I am going to be very direct and hit a few important points. 1) When you are bent over looking inside a project you are turning, you can't really see much. I did this 15 years ago (once), got a catch and the tool handle hit me in the face, throwing my glasses off and cutting me. 2) If you watch any number of hollowing videos you will see that turning by feeling the tool cutting is all you need to do. This comes with experience. 3) When you are bent over you are in a very uncomfortable position. Practice on an open bowl and turn by simply feeling the tool contacting the wood. You will find this works. If you ever do turn while looking into the inside of a piece, make sure your head is NOT over the tool handle. Sam

[@imapseudonym1403]

Thanks. I guess I need a LOT more practice.

[@WYOMINGWOODTURNER]

IMA....I started to make a video on this topic today.....I think it is important Sam

[@imapseudonym1403]

I will certainly watch it! Thanks very much!

[@WYOMINGWOODTURNER]

Ima Pseudonym I finished the video. I think it is a good topic. I will not have it out for 3 or 4 weeks. Sam

[@keawoodturningstudiohawaii1183]

Sam, you could really improve the quality of your videos if you get in touch with Alan Zenreich or me. He was demoing in Atlanta, and will be again next year, with me, maybe helping him. He teaches how to use a very simple program, Vmix, with 3 cameras. I have been doing some clases remotely and works great! I'm the president of the Maui Woodturners Assn. Lyle Jamieson and our club did the first "documented" Live remote interactive demo. We have an article coming out in the Journal soon!! I use an old iPhone, as one of the 3 cameras, I can show live inside a bowl, with the light of the phone... We would love to have you demo for us from the confort of your own shop!! Soon the AAW will have a list of available demo professionals that can do it remotely!! You can call me if you have any questions, we are friends on Facebook, or look me up thru my web site: www.hawaiiankoaturner.com Aloha from Maui.

[@WYOMINGWOODTURNER]

Thanks for the information and advice. This comment I am responding to is on a video I made in 2013. I am sure you are also looking at some of my current videos. For me it is a matter of "hours in the day". I spend upwards of 20 hours on a video. Some less and some actually more. That time includes editing etc. Probably for 20 or 30 of my last videos are done with two cameras. But, I am sure i can improve. I am just not sure if I have the time or inclination to improve more from the quality of my current videos. If you look at Glenn Lucas' videos, they are outstanding. They are each a work of art. If I advance to that level I will need to buy a $5000 camera, a sound system and who knows what else. I am just not interested in spending more time learning a new editing program and adding a camera. I am a woodturning. I make videos for other woodturners. Sorry for the diatribe. Sam

[@ridterranytofollowtruthpea8324]

WYOMINGWOODTURNER, And all of your dedicated followers, myself especially, thank you much for your time and help in sharing your wisdom and knowledge!!! Your camera work is just fine!!! Take care Sam!!!

[@matthewharper170]

god I cringe when you woodturners do that, great video Sam

[@WYOMINGWOODTURNER]

Matthew Harper You mean when I break the bowl in two? I love the shock element. Sam

[@matthewharper170]

WYOMINGWOODTURNER haha, yes that

[@WYOMINGWOODTURNER]

Thanks Sam

[@WYOMINGWOODTURNER]

Thanks Sam