SolidWorks RE Tutorial

  Рет қаралды 5,917,613

SolidWorks Tutorial ☺

SolidWorks Tutorial ☺

Күн бұрын

Пікірлер: 1 000
@dice1456
@dice1456 5 жыл бұрын
1. Piston 2:32 2. Crank Shaft 23:42 3. Engine Block 31:53 4. Rocker Arm 47:26 5. Cylinder Head 1:06:12 6. Exhaust Manifold 1:27:04 7. Air Filter 1:41:13 8. Cam Shaft 1:46:08 9. Valve 1:52:53 10. Rocker Spring 1:54:52 11. Belt Wheels 1:58:39 12. Intake Manifold 2:06:21 13. Front Cover 2:18:26 14. Oil Pan 2:26:24 15. Air Turbo 2:36:36 16. Valves Cover 2:49:00 17. C. Retainer 2:56:25 18. C. Bushings 2:59:10 Lower Block Assembly 3:01:13 Upper Block Assembly 3:07:07 Outside Stuff Assembly 3:18:44 Shaft & Belts connecting 3:27:24 Exhaust Hoses Assembly 2:34:55
@张奎-d5k
@张奎-d5k 5 жыл бұрын
Doğru videoyu nasıl bulurum?
@kevinleonsanchez7111
@kevinleonsanchez7111 5 жыл бұрын
The rocker arm has a little bit of shortcut. He showed how its made, but upon assembly, it was a different object.
@sundarramanj1608
@sundarramanj1608 5 жыл бұрын
@@kevinleonsanchez7111 yes bro, I also see it
@thompsn_9934
@thompsn_9934 4 жыл бұрын
@@kevinleonsanchez7111 kzbin.info/www/bejne/e57Pe2SXoNVrsLM
@kushagraroy5081
@kushagraroy5081 4 жыл бұрын
Contact me for V6 Engine drawing Email- kushagraroy1@protonmail.com
@plinsavi
@plinsavi 5 жыл бұрын
In the connecting rod part, you have to change the dimension of the bigger hole from 76.2 to 63.5. There is an editing cut in the video that doesn't show that he changed the dimension. In 4:23 you can kind of see that the new dimension is 63.5. Like this comment for people to see it.
@VAB1990
@VAB1990 4 жыл бұрын
Yes i noticed it but after I got stuck where we do extruded cut on the sides at 6:40
@mandiesmith5483
@mandiesmith5483 4 жыл бұрын
plinsavi good job
@cecilkoranteng2014
@cecilkoranteng2014 4 жыл бұрын
Would it be possible to get a pdf of the parts with dimensions
@okgbp
@okgbp 4 жыл бұрын
which is correct though? The 76.2 seems like a corrected value.
@mateenlakhani621
@mateenlakhani621 4 жыл бұрын
@@okgbp but how do u do the extruded cut at 6:40 ?
@crazy031089
@crazy031089 4 жыл бұрын
For those off you not properly realizing: This is not a real engine. There are a large number of (small) mistakes and simplifications, wich mean this would never work. It is a good start however to use to explain how an engine works. But most importantly, this is a nice tutorial to show what is possible in solid works and how to do it. This also means that the exact dimensions don't matter at all.
@jilbake
@jilbake Жыл бұрын
Im just gonna say it. I wish I was that smart. I am a diagnostic consultant for a major automaker supporting dealerships nation wide and its not a job for a dummy, but when I see you do that, I feel like a complete box of rocks. That is awesome work
@crapcopter
@crapcopter 3 жыл бұрын
Woke up to this on my phone at 3am. Not disappointed.
@loicbarre6349
@loicbarre6349 3 жыл бұрын
I paused the video at 3:32:45, because it shows two things I don't understand. First I see the PartR11 floating. Secondly, it looks like the CamShaft Retainer is coming out of the Valves cover. Also, with a bigger project like this it is easier to number your parts. I like to use the reference numbers as following; 1.1.1-A-[Part name]. First number is referring to the project number (or main assembly). Second number is for sub-assembly. Third number for part number. Letter for revision references ("A" being "REV0" and "B" being a revision of "A", and so on). This will not only help finding your parts faster. It also orders them and you can still search them by name. This really comes in handy whenever you add all the bolts etc. to your project folders as well. Other than that very inspiring video!
@xuancuongbui764
@xuancuongbui764 4 жыл бұрын
47:26 The "Rocker arm" part is different from the previous assembly.
@giorgioforcella2609
@giorgioforcella2609 4 жыл бұрын
kzbin.info/www/bejne/e57Pe2SXoNVrsLM here you can find the rocker arm used
@yzl6284
@yzl6284 4 жыл бұрын
@@giorgioforcella2609 so the one in another playlist is the one he is using ?
@giorgioforcella2609
@giorgioforcella2609 4 жыл бұрын
@@yzl6284 Exactly
@kathirvelmuruganandam7214
@kathirvelmuruganandam7214 3 жыл бұрын
@@giorgioforcella2609 Thank you Brother.
@Vanguyen09
@Vanguyen09 3 жыл бұрын
Xuan Cuong Bui. Did you built and post this engine? Very good job. Thank you. I learn a lot overall from this video. Especially on (boundary boss, loft, sweep, and mating on cam, mirror copy or rotate on cam shaft). I have 2021 version, but I can figure out to match you version of mating in solidworks. There is a little problem on (intaker manifold, I did mirror and copy, but the mirror part only matching one side of cylinder head, the other side was off air vents). Can you let me know what's wrong? Thank you.
@BrozakJaslene
@BrozakJaslene Жыл бұрын
Bạn không chỉ làm tăng số lượng mà còn tạo ra sự tương tác chân thực và ý nghĩa. Điều này giúp nội dung của mình trở nên phong phú hơn
@abdilrazaqadam3433
@abdilrazaqadam3433 4 жыл бұрын
all i can imagine is the feeling after executing this masterpiece work
@VARLIVE
@VARLIVE 4 жыл бұрын
Hi dear friend 👋 😊 Can you check my Motor AC design: kzbin.info/www/bejne/ooKvk56LZdyre80
@pipthewarrior3738
@pipthewarrior3738 Жыл бұрын
He felt 10 fps of it
@nopelindoputraperkasa5869
@nopelindoputraperkasa5869 10 ай бұрын
SolidWorks RE Tutorial #320 : Car Engine complete video (2 turbo V6) - (advanced assembly)... Amazing Vidio 🇮🇩😍🙏👍
@itshakchattopadhyay6014
@itshakchattopadhyay6014 2 жыл бұрын
For anyone getting knitting errors for the turbo change the distance between the rectangles from 80.45 -> 80.95 and increase/decrease the number or sections to the maximum/ minimum. It works on the newest catia version that way
@paulmitzlaff6952
@paulmitzlaff6952 2 жыл бұрын
Thanks for this. It just worked for me in Solidworks
@alessandroscovoli7122
@alessandroscovoli7122 2 жыл бұрын
Bro but where he took the principal part of racket arm? Help draw a piece and in assembly help took another
@swelch4266
@swelch4266 2 жыл бұрын
Thank you so so much!
@matteomonti1454
@matteomonti1454 Жыл бұрын
thanks
@filippoelmi7331
@filippoelmi7331 Жыл бұрын
@ashutoshdubey8117
@ashutoshdubey8117 Жыл бұрын
After countless failed attempts, this working version feels like a breath of fresh air.
@shammideepak5677
@shammideepak5677 Жыл бұрын
Hello can you send me the file
@Fluttydev
@Fluttydev 7 жыл бұрын
You should upload the parts description with exact dimensions this will really help full for us, thanks
@kef1kef2kef3kef4kef5
@kef1kef2kef3kef4kef5 4 жыл бұрын
@@kushagraroy5081 E-mailed u, still available?
@volkanuzey6932
@volkanuzey6932 4 жыл бұрын
@@kef1kef2kef3kef4kef5 can u take the drawing?
@ilgazuzumoglu7093
@ilgazuzumoglu7093 4 жыл бұрын
@@kushagraroy5081 i sent you email
@carlosenriquesalassoto7373
@carlosenriquesalassoto7373 4 жыл бұрын
@@ilgazuzumoglu7093 Can you send them to me too?
@zephinsgeorge5910
@zephinsgeorge5910 4 жыл бұрын
@@kef1kef2kef3kef4kef5 hey did you get the drawings???
@ronicksamuel2912
@ronicksamuel2912 4 жыл бұрын
the 4 tutorial "Rocker Arm" is not complete/correct, please i need the complete/correct video on rocker Arm. thanks
@GigaChad-hf4yo
@GigaChad-hf4yo 4 жыл бұрын
here check this kzbin.info/www/bejne/e57Pe2SXoNVrsLM
@jorgeluisquiroz2356
@jorgeluisquiroz2356 4 жыл бұрын
@@GigaChad-hf4yo Muchas gracias
@유오유오예
@유오유오예 4 жыл бұрын
@@GigaChad-hf4yo 감사합니다!
@amityadav-dz3uw
@amityadav-dz3uw 2 жыл бұрын
Qqqqqqsq1qqssqaqaaqqqq wwqstwq
@王玲-t7o
@王玲-t7o 3 жыл бұрын
其实用快捷工具栏比较好~鼠标笔试可以设置为8笔试的!用布局草图的形式自顶向下建模,效率会高很多,像楼主这种只适合已知规格的;零部件制作,如果碰见比较大的项目或是需要反复测试论证修改的项目,这种方法就捉襟见肘了,因为稍微一改动,装配关系就会有一大推的报错!!! 个人意见,不要喷~ 欢迎交流!
@lono4.631
@lono4.631 Ай бұрын
How to activate
@nirajsirvi4780
@nirajsirvi4780 4 жыл бұрын
Big problem with rocker arm u make different and in assembly it comes as different part how
@bahaazidan9218
@bahaazidan9218 4 жыл бұрын
I had the same problem
@agastinjebaraj5111
@agastinjebaraj5111 4 жыл бұрын
Same problem
@yincheolhong6735
@yincheolhong6735 4 жыл бұрын
You can found that at this link. kzbin.info/www/bejne/e57Pe2SXoNVrsLM
@numandalaslan6360
@numandalaslan6360 4 жыл бұрын
how did you fix this?
@onurcanmucuk3287
@onurcanmucuk3287 4 жыл бұрын
@@yincheolhong6735 Thanks Dude
@jumbo999614
@jumbo999614 6 жыл бұрын
Anyone has the problem as mine 3:15:04 the rockerarm loses its alignment? This happens whenever i save the assembly. I have to manually realign it.
@haxlow5420
@haxlow5420 5 жыл бұрын
Did you find any solution for this ?
@ShadiSaffour
@ShadiSaffour 4 жыл бұрын
i have the same problem as well, any solution?
@dhruvenshingadiya127
@dhruvenshingadiya127 4 жыл бұрын
Same problem hear bro plz solution send me plz
@jumbo999614
@jumbo999614 4 жыл бұрын
@@dhruvenshingadiya127 Sorry. No solution. Maybe it's program's bug.
@fajoieachabbak8709
@fajoieachabbak8709 3 жыл бұрын
​@@dhruvenshingadiya127 you have to go 'advanced mates' when you select for Distance , Maximum value is 48mm and minimum value is 0 and done
@vikassingh4151
@vikassingh4151 5 жыл бұрын
at 7:05 the sketch which shows the rectangle doesn't lie inside any of the circles if the dimensions re not changed further please revert back
@romlef526
@romlef526 7 жыл бұрын
Magnifique !!!! , la seule petite chose manquante sur ce moteur est une animation automatique !!!! résultat superbe !!!!!
@antoinealzieu3477
@antoinealzieu3477 Жыл бұрын
salut ta pas eu de problème avec le culbuteur ? il a dessiné une pièce mais au moment de l'assemblage ce n'était pas le même
@MrWilli117
@MrWilli117 9 ай бұрын
j'ai eu le meme probleme figure toi @@antoinealzieu3477
@mahdielsaid6103
@mahdielsaid6103 2 жыл бұрын
I'm having a problem in making a linear pattern at 1:14:38 on the cylinder head, it says geometry failed or tell me to check my lofts or decrease the instance or distance.
@gameaccount2541
@gameaccount2541 Жыл бұрын
i am having the same problem too
@paarthjangra6742
@paarthjangra6742 Жыл бұрын
Any solution?
@paarthjangra6742
@paarthjangra6742 Жыл бұрын
@@gameaccount2541 any solution?
@praveenkumar-kb4nj
@praveenkumar-kb4nj 3 жыл бұрын
Great.It would be very usefull if you provide technical details of each part and Specify their measures in a Pdf file.I would have loved to recreate this model for my assignment.
@arthurclaeys7100
@arthurclaeys7100 3 жыл бұрын
Very nice project to do on your own, I learned to use a lot of new features I didn't know before. There were some faults in the intake manifold: some open spaces and it didn't fit on both sides of the cilinderheads. I was able to draw an entire new intakemanifold on my own without these open spaces, and it fitted perfectly on the cilinderheads, which shows that I really am feeling confident with these features. Also, on both sides of the valvescovers, there were camshaftretainers intersecting with the valvescovers, that was an easy fix :)). The hoses didn't fit on the turbos, so I had to change the diameter of the turbo outlet. The gearratio between crank and camshaft was switched too. I also drew a complete exhaust system that fitted on the existing exhaustmanifolds. I Would recomend this for anyone who is interested in how a combustion engine works and if you want to improve your solidworks skilss.
@user-uo5jk6kw6c
@user-uo5jk6kw6c 3 жыл бұрын
Can you guide how to make the correct exaust manifold?
@arthurclaeys7100
@arthurclaeys7100 3 жыл бұрын
@@user-uo5jk6kw6c you mean intake manifold? Nothing wrong wigh the exhaust manifold?
@user-uo5jk6kw6c
@user-uo5jk6kw6c 3 жыл бұрын
@@arthurclaeys7100 Yes, intake manifold. Did you faced any problem in that? In comments I see that many people are complaining about that part. Have you got that part correct?
@arthurclaeys7100
@arthurclaeys7100 3 жыл бұрын
@@user-uo5jk6kw6c yes I had some trouble with it, its a bit hard to explain how i fixed it. I can send it to you if you want...
@user-uo5jk6kw6c
@user-uo5jk6kw6c 3 жыл бұрын
@@arthurclaeys7100 yes please, it would really mean a lot. Other than this part, I have done others. So can we connect through mail or Whatsapp anything you want
@andreeew1123
@andreeew1123 5 жыл бұрын
can you please gives as link /pdf to dimensions of those parts i would like to try it by my self without tutorial
@ahmeds4
@ahmeds4 5 жыл бұрын
You can put your own dimensions and just follow the process
@andreeew1123
@andreeew1123 4 жыл бұрын
@@ahmeds4 but i want to do it by myself without the tutorial
@TheBountyHunter-666
@TheBountyHunter-666 4 жыл бұрын
Yes .. we want pdf or link of those parts please.
@kushagraroy5081
@kushagraroy5081 4 жыл бұрын
Contact me for V6 Engine drawing Email- kushagraroy1@protonmail.com
@kushagraroy5081
@kushagraroy5081 4 жыл бұрын
@@TheBountyHunter-666 Contact me for V6 Engine drawing Email- kushagraroy1@protonmail.com
@andrewg66
@andrewg66 6 жыл бұрын
guys at 28:15 it might be incorrect, the mirror plane should be the surface of the thin cylinder, not the thick one
@YOGESHKUMAR-bb8pu
@YOGESHKUMAR-bb8pu 6 жыл бұрын
Hello Andrew are u a automobile engineering
@300ml_brasil
@300ml_brasil 6 жыл бұрын
amazing such english much wow
@300ml_brasil
@300ml_brasil 6 жыл бұрын
the 76.2 should also be the thin cylinder.
@omkarkalaskar3823
@omkarkalaskar3823 4 жыл бұрын
Iam facing problem while assembling intake manifold. I think the part while doing assembly operation is different in dimensions then you showed in your video. Please help to resolve this problem..
@matiasvestergaard5612
@matiasvestergaard5612 4 ай бұрын
57:18 how can that rocker arm be to 1:01:28? im rly confused about that? i cant see a way they are the same? 🙂
@Ghost-ro2oy
@Ghost-ro2oy 3 жыл бұрын
Hi there. Thank you for the video. It's excellent. I will post here some tips for you guys to do the full engine. Here some corrections : 1) When you start the PistonRod at 3:55, make sure the dimension of 76.2 is always changed to 63.5 (you'll notice that he corrected it at 4:21). Thanks to plinsavi for finding this correction. 2) Make sure that all sketches are constrained (completely black), specially when you copy some patterns. 3) At 47:25, a weird rocker arm is designed, which doesn't fit in the assembly. Stop there. The correct rocker arm is here : kzbin.info/www/bejne/e57Pe2SXoNVrsLM Then jump directly to 57:40 to start the next part 4) after finishing the IntakeManifold1 (2:17:56), you'll notice that it is not perfect, because of how the middle part is connected to the 3 boundaries. A solution would be to add an extra sketch. for this, follow these steps : a) Move the Boss-Extrude8 on the tree to the top, just under Plane2 b) On the extruded face, create a new sketch and convert the entities in order to have a copy of the initial sketch (make this one visible to be able to copy it) c) on the tree line, Move the new sketch and place just after the Boss-Extrude8 d) Modify the Boundary1, Boundary2 and Boundary3 by using the new sketch, instead of the old one. Follow exactly the same steps show on the video. e) The result is a clean connection between the middle part and the different boundaries. 5) About the 5/16 hole at 2:33:00 : I tried several times with the shown values but it didn't work. After some tests, the custom sizing should be approximately : Diameter of the primary hole: 1.5in Major hole diameter : 0.332in Depth : 0.235in 6) When designing the CrankShaft Bushing (2:59:37), change the dimension of 76.2mm to 63.5mm. Otherwise, the CrankShaft will not fit into it at 3:03:14. 7) After adding the hoses at 3:40:16, you'll notice that they don't fit with the Airturbos. I suggest to modify the exhaust of the airturbos to have an external diameter of 50.8mm.
@atakanpolat7707
@atakanpolat7707 3 жыл бұрын
Thank you !
@Ghost-ro2oy
@Ghost-ro2oy 3 жыл бұрын
@@atakanpolat7707 you're welcome. Anytime
@devanshujoshi8393
@devanshujoshi8393 3 жыл бұрын
thank you so much for this effort i appreciate you my friend !! :)
@trihuynhngoc7415
@trihuynhngoc7415 3 жыл бұрын
many thanks !
@pratiksharma4002
@pratiksharma4002 3 жыл бұрын
Do u have all parts dimensions photos of pdf if yes then plz email me on sharmapratik727@gmail.com.
@miipauu3173
@miipauu3173 12 күн бұрын
where is the drawing plan sir
@e.t5102
@e.t5102 Жыл бұрын
Hi!Can you share the technical drawings of them if it's okay for you?I want to try on my own first. :)
@barathsaai9386
@barathsaai9386 3 жыл бұрын
I am not able to rotate the crankshaft after mating more than two pistons, please can I get a clear video for the assembly part alone?
@dudleyparkfmx336
@dudleyparkfmx336 2 жыл бұрын
Thanks, great video, appreciate the time you spent making the video. Had to laugh watching your computer almost dying at the end trying to animate the assembly. Good work my friend.
@vasudevan3195
@vasudevan3195 5 жыл бұрын
Rocker arm 4 first part 1 is not drowned for assembly. Different parts of part1 in assembly and drawing. Simply "Rocker arm part 1 is missing" Check it please. U drowned a part in @57:23 and but in assembly u used different part @1:01:30
@kevinleonsanchez7111
@kevinleonsanchez7111 5 жыл бұрын
Yes, I also saw it. It was a different kind of rocket arm which he made than the one in assembly.
@kevinleonsanchez7111
@kevinleonsanchez7111 5 жыл бұрын
I think this is the rocker arm kzbin.info/www/bejne/e57Pe2SXoNVrsLM
@bejaouirached8419
@bejaouirached8419 5 жыл бұрын
@@kevinleonsanchez7111 thank you Kevin that's the part i need it.save me a lot of time
@KristineLyall
@KristineLyall Жыл бұрын
great video i did it the first time and it worked thought i would need to get someone out to help me but you explained it well and it worked thank you
@ermdallauddinansari1948
@ermdallauddinansari1948 3 жыл бұрын
I follow you sir and learn basic and advance knowledge sir
@pulsarmclaren8463
@pulsarmclaren8463 3 жыл бұрын
Hello ! Please, the 4th piece you draw is not thé same you used for the assembly. How can I do to have the good dimensions for the real rocker arm? Sorry if my english is not goot I'm not anglophone.
@eloualidchakir45
@eloualidchakir45 3 жыл бұрын
kzbin.info/www/bejne/e57Pe2SXoNVrsLM
@txqi
@txqi 6 жыл бұрын
Great video. Would it be possible to give the technical details of each part? Specifically their measures? I would have loved to recreate this model for my university assignment (giving you credit for its design), but my teachers did not accept it, for a lack of proper technical details. Still, I did recreate some parts just for fun and practice and learned a lot! So thanks!
@Uu-vr3wr
@Uu-vr3wr Жыл бұрын
Did you find any
@seanhammond3443
@seanhammond3443 5 жыл бұрын
56:09 what are the specs of the tapped hole because i dont get that lip on top of the cut
@Madmate9161
@Madmate9161 4 жыл бұрын
I have the same problem, how did you fix it
@ahmedmaher4667
@ahmedmaher4667 3 жыл бұрын
@@Madmate9161 Be sure that you are normal on the surface before you tap, because the surface you are trying to tap on it is inclined to the plane
@aliqawqazeh7199
@aliqawqazeh7199 4 жыл бұрын
can you give me the specifications on drawing of all parts like pdf file ???
@tooldesigntech3819
@tooldesigntech3819 3 жыл бұрын
kzbin.info/www/bejne/fJe5h3yhqbJpqK8* SUBSCRBE FOR MORE DETAIL
@devashishvashisth6716
@devashishvashisth6716 2 жыл бұрын
Rocker arm is different in assembly??
@loanjl164
@loanjl164 2 жыл бұрын
Yess
@melekdeniz8173
@melekdeniz8173 3 жыл бұрын
We did the process while drawing the rocket arm, but another part was used in the assembly part, so I couldn't do the rocket arm assembly, now it will affect the main assembly
@danveysey2223
@danveysey2223 3 жыл бұрын
This should be the rocker main body you need to assemble the whole rocker arm.kzbin.info/www/bejne/e57Pe2SXoNVrsLM&ab_channel=SolidWorksTutorial%E2%98%BA
@davidhernandez-mr4qr
@davidhernandez-mr4qr 3 жыл бұрын
The rocker arm showed doing the piece and showed in the assembly arent the same
@antonioxavierdcosta5610
@antonioxavierdcosta5610 4 жыл бұрын
Turbocharger works with the help of exhaust gases...... The turbocharger in the video doesn't seem to work with exhaust gases...
@ranjeetjadhav367
@ranjeetjadhav367 Жыл бұрын
i am confuse at rocker arm assembly at 1:01:22 which part is add in that assembly? when this part is make please suggest....
@ahmedmohsen1109
@ahmedmohsen1109 5 жыл бұрын
at 3:56 using the 76.2 dimension made the extruded cut at 6:42 extended through the semi circle and made it a through-slot What did I do wrong?
@謝維倫-h1v
@謝維倫-h1v 5 жыл бұрын
same....
@renanjauregui8705
@renanjauregui8705 5 жыл бұрын
the actual dimension is 63.5
@plinsavi
@plinsavi 5 жыл бұрын
@@renanjauregui8705 Visually, the dimension you wrote does seem correct. But does it match the crankshaft diameter later? I would have to check the rest of the video...
@plinsavi
@plinsavi 5 жыл бұрын
@@renanjauregui8705 You are correct, sir. There is a cut in the video in 4:21, and the dimension changed.
@nargasliman961
@nargasliman961 3 жыл бұрын
2D sketch where can be found ?
@vasudeokatdare6530
@vasudeokatdare6530 4 жыл бұрын
DEAR SIR, IS THERE ANY MISS MATCH IN ROCKER ARM PART DRAWING? CAUSE,SHOWN IN TUTORIAL & SELECTED FOR ASSEMBLY IS NOT MATCH WITH EACH OTHER. PLEASE GUIDE ME.
@thaneshprasath6279
@thaneshprasath6279 4 жыл бұрын
Yes even I seen it now what to do ?
@mayankchikane8797
@mayankchikane8797 4 жыл бұрын
@@thaneshprasath6279 check his playlist for separate parts
@arceskeleto5803
@arceskeleto5803 3 жыл бұрын
After further inspection, small Timing belt wheel, camshaft don't match. Cylinder heads assembled inversed. And many more things to repair once modeled.
@ozguniloglu7133
@ozguniloglu7133 6 жыл бұрын
At the beginning of the video, on the right, while sketching the third circle the diameter was given as 76.2 mm but this is tricky ! The real dimension is something like 6.. Why did you do this ? Whats your purpose ?
@aldebj7379
@aldebj7379 5 жыл бұрын
You are complety right, I was confused about the dimensions.
@endurenova
@endurenova 5 жыл бұрын
Somehow!!! I waas confused too!!
@silvinosanchez8841
@silvinosanchez8841 5 жыл бұрын
So. What it is the correct dimension? I confused to..
@mucilan217
@mucilan217 5 жыл бұрын
i love your courage, sweet! i was confused so much!!
@Shepard5544
@Shepard5544 5 жыл бұрын
@@silvinosanchez8841 At 4:21, you can see that is 63.50
@MohasinVatti-px7kk
@MohasinVatti-px7kk Жыл бұрын
Thanks!
@akshaybhapkar1626
@akshaybhapkar1626 3 жыл бұрын
Took me 6 days to complete the whole...There are some errors in the dimensions of components. But overall, I liked it. I learned a lot about different mates. ..Keep up the good work. You should've attached some animation as well.
@rajivshenoy897
@rajivshenoy897 3 жыл бұрын
Can you please let me know about the rocker arm dimensions in the video
@akshaybhapkar1626
@akshaybhapkar1626 3 жыл бұрын
@@rajivshenoy897 kzbin.info/www/bejne/e57Pe2SXoNVrsLM
@gregorylincoln4328
@gregorylincoln4328 3 жыл бұрын
@@rajivshenoy897 eb b. Bf b b. F b fb. V g b. f v. B f f ff v v bfb. Efv b b f vv. V. G fe b b. G. E. V g gv f b g. F b vb b. V. g. V. Vebvfef fb bff. b fffb b. F fe b f b e b. B . E.bb .bfv. f. F.b. B.f.bb. B fbfb fbb. Bf bfb..b..bb b .b.b .b.v.bf.bf. eb...fb...b.b.f.bff fff.b.b.bb... b..bffe.b .vfb.f.bff fe .f. V. Fff b.f b. V f b. f fb.. .bb v . F.b. .b.v.f f.bf f bff ..f v f. f v vbfc.ffffv. .v f f ff ff. f fv. B v. F f bf. F . Bff b. B b.ff.bffb..fb.e fb.ff.b. v eefb.bff.b. q q q. Q q q qs qqq q qq. Qq q qq qqq. Q q. Q. Qq qqq q q. Qq qqq q. Q q. Qq q q q. Qaqqq qq Q qqQ q qq Q. QqQ. Q qqqq Qq qQ q qqqq. Q qq qqq. Q qqqq qqq. Qqq qq q. Qqq q qq. QQqqq Q q q q. QqqQq q qq qqq q Qq q qqq Q q Q q q q Q q q q q Q q. Q Q. Qq q qq q . Qq q q qqq qq q q q qq q Q Q qqq qq. Q. Q. Q. Qqq q q q qq qqq qqqq q qq Q q. Q qq q q. Q Q Q Q q q q Q q Q qqq qqqq Q q Q Qqqq qq Q Qqq qqqqQ q q qqq q. Qqqq q qq qQ q qq q qq q. Qq qqq Q Qqq qq q q q. Qqq Q. Q. Q Qq qqq. Q. Qq qqqqq Q qq qqq. QQ qq d Qqq q qq q q Q qq Q Q qq Q qqq Qq. Q q Q. Q Qq qq. Q qq q qqqq. Q q q Q q qqq qQ. Q q qqq qq Q qq Q q qqQ Qq. Q Q. qq qqq qq q q qqqq Q. Q Qqq q q q qqq qq. Q q. Qq q q qq qq q qq qqq qq. Q. Qqqqq q q qqq q q qqq q qqq
@gregorylincoln4328
@gregorylincoln4328 3 жыл бұрын
@@rajivshenoy897 eb b. Bf b b. F b fb. V g b. f v. B f f ff v v bfb. Efv b b f vv. V. G fe b b. G. E. V g gv f b g. F b vb b. V. g. V. Vebvfef fb bff. b fffb b. F fe b f b e b. B . E.bb .bfv. f. F.b. B.f.bb. B fbfb fbb. Bf bfb..b..bb b .b.b .b.v.bf.bf. eb...fb...b.b.f.bff fff.b.b.bb... b..bffe.b .vfb.f.bff fe .f. V. Fff b.f b. V f b. f fb.. .bb v . F.b. .b.v.f f.bf f bff ..f v f. f v vbfc.ffffv. .v f f ff ff. f fv. B v. F f bf. F . Bff b. B b.ff.bffb..fb.e fb.ff.b. v eefb.bff.b. q q q. Q q q qs qqq q qq. Qq q qq qqq. Q q. Q. Qq qqq q q. Qq qqq q. Q q. Qq q q q. Qaqqq qq Q qqQ q qq Q. QqQ. Q qqqq Qq qQ q qqqq. Q qq qqq. Q qqqq qqq. Qqq qq q. Qqq q qq. QQqqq Q q q q. QqqQq q qq qqq q Qq q qqq Q q Q q q q Q q q q q Q q. Q Q. Qq q qq q . Qq q q qqq qq q q q qq q Q Q qqq qq. Q. Q. Q. Qqq q q q qq qqq qqqq q qq Q q. Q qq q q. Q Q Q Q q q q Q q Q qqq qqqq Q q Q Qqqq qq Q Qqq qqqqQ q q qqq q. Qqqq q qq qQ q qq q qq q. Qq qqq Q Qqq qq q q q. Qqq Q. Q. Q Qq qqq. Q. Qq qqqqq Q qq qqq. QQ qq d Qqq q qq q q Q qq Q Q qq Q qqq Qq. Q q Q. Q Qq qq. Q qq q qqqq. Q q q Q q qqq qQ. Q q qqq qq Q qq Q q qqQ Qq. Q Q. qq qqq qq q q qqqq Q. Q Qqq q q q qqq qq. Q q. Qq q q qq qq q qq qqq qq. Q. Qqqqq qqqqq. Q qq q q qqq q q qqq q qqq
@gregorylincoln4328
@gregorylincoln4328 3 жыл бұрын
@@rajivshenoy897 eb b. Bf b b. F b fb. V g b. f v. B f f ff v v bfb. Efv b b f vv. V. G fe b b. G. E. V g gv f b g. F b vb b. V. g. V. Vebvfef fb bff. b fffb b. F fe b f b e b. B . E.bb .bfv. f. F.b. B.f.bb. B fbfb fbb. Bf bfb..b..bb b .b.b .b.v.bf.bf. eb...fb...b.b.f.bff fff.b.b.bb... b..bffe.b .vfb.f.bff fe .f. V. Fff b.f b. V f b. f fb.. .bb v . F.b. .b.v.f f.bf f bff ..f v f. f v vbfc.ffffv. .v f f ff ff. f fv. B v. F f bf. F . Bff b. B b.ff.bffb..fb.e fb.ff.b. v eefb.bff.b. q q q. Q q q qs qqq q qq. Qq q qq qqq. Q q. Q. Qq qqq q q. Qq qqq q. Q q. Qq q q q. Qaqqq qq Q qqQ q qq Q. QqQ. Q qqqq Qq qQ q qqqq. Q qq qqq. Q qqqq qqq. Qqq qq q. Qqq q qq. QQqqq Q q q q. QqqQq q qq qqq q Qq q qqq Q q Q q q q Q q q q q Q q. Q Q. Qq q qq q . Qq q q qqq qq q q q qq q Q Q qqq qq. Q. Q. Q. Qqq q q q qq qqq qqqq q qq Q q. Q qq q q. Q Q Q Q q q q Q q Q qqq qqqq Q q Q Qqqq qq Q Qqq qqqqQ q q qqq q. Qqqq q qq qQ q qq q qq q. Qq qqq Q Qqq qq q q q. Qqq Q. Q. Q Qq qqq. Q. Qq qqqqq Q qq qqq. QQ qq d Qqq q qq q q Q qq Q Q qq Q qqq Qq. Q q Q. Q Qq qq. Q qq q qqqq. Q q q Q q qqq qQ. Q q qqq qq Q qq Q q qqQ Qq. Q Q. qq qqq qq q q qqqq Q. Q Qqq q q q qqq qq. Q q. Qq q q qq qq q qq qqq qq. Q. Qqqqq qqqqq. Q q. Q. Qq q q qqq q q qqq q qqq
@nichlashlenschlger9796
@nichlashlenschlger9796 3 жыл бұрын
I may be stupid, but how does it make sense with a thread longer than the hole? :)
@johnjames1994
@johnjames1994 6 жыл бұрын
can i use the rocker arm in the play list for this assembly?
@kushagraroy5081
@kushagraroy5081 4 жыл бұрын
Contact me for V6 Engine drawing Email- kushagraroy1@protonmail.com
@cadmech4740
@cadmech4740 4 жыл бұрын
@@kushagraroy5081 can you send me the drawing on shanespinwarne0@gmail.com
@santhoshs4509
@santhoshs4509 4 жыл бұрын
@@kushagraroy5081 can you please send me the drawing or rocker arm related information to santhoshsanthosh710@gmail.com Thanks in advance
@mayanksinghal6794
@mayanksinghal6794 3 жыл бұрын
Hey kushagra, can you please send the rocker arm part design via mail mayanksinghal6768@gmail.com , Thankyou.
@shreyashghare6838
@shreyashghare6838 3 жыл бұрын
Very Good efforts taken.
@STRMCathriyn
@STRMCathriyn 5 жыл бұрын
Hi guys, I have a problem with the rocker arm and cam shaft, when I use the "cam mate" I can select only 1 face from the cam shaft, and when it spins, the rocker arm goes down, below the cam, any advice on this matter ?
@avinashn9945
@avinashn9945 4 жыл бұрын
dude, did you find the solution for that?
@STRMCathriyn
@STRMCathriyn 4 жыл бұрын
@@avinashn9945 If I remember right I set a limit distance for the rocker arm, so that it can't go below the cam
@avinashn9945
@avinashn9945 4 жыл бұрын
@@STRMCathriyn I have already done that. But still have cam mating issue
@STRMCathriyn
@STRMCathriyn 4 жыл бұрын
@@avinashn9945 set the limit distance from the cam bolt and the cylinder head
@jeyaraman4711
@jeyaraman4711 3 жыл бұрын
@@STRMCathriyn Can you please tell me clearly to solve that problem?
@ZQYM-Molly
@ZQYM-Molly 4 ай бұрын
Thank You I Just Love this Channel.
@a.elmehni6954
@a.elmehni6954 4 жыл бұрын
I saw the video at 0.5 speed, so, almost seven hours of learning !!! Thank you
@nadavnmy
@nadavnmy 3 жыл бұрын
thanks, there is a big issue Intake Manifold Holes remained in the body
@jorgeveracazarin8486
@jorgeveracazarin8486 4 жыл бұрын
Hello! i am going to tell you how i fix the problem with the holes in the intake manifold .step1.- offset the 6 squares 6.35 (outside) before boundary base (i used lofted boss now). step 2.- convert intities that 6 offset squares. step 3.- hide the first 2 sketches and use the 2 sketches with only the offset squares. step3.- use lofted boss instead of boundary base with the offset squares (in star/end constraints put normal to profile in both) step4. Show again the first 2 sketches to extrude the squares as shown in the video (extruded complete without selecting contour) . step5.-in a new sketck convert into intities the 6 original squares and keep only this 2 sketches (hide the others) step6.- lofted cut and set both normal to profile. step 7.- continue with the rest. Hope this could help you and sorry if my english is not the best. like so everyone can see this
@jaredthebest47
@jaredthebest47 4 жыл бұрын
Thats a great solution! here's the process I used: 1. Continue the tutorial as shown until you get to the extrusions 2. Extrude as shown but include the holes as well, make sure to turn off 'merge result' 3. Use the intersect tool and select all bodies, click 'intersect' 4. you can now select which intersections to delete. Select the insides of the manifold as needed. That's it! this way you can stick with the video tutorial most of the way.
@ThanhHa-sl6py
@ThanhHa-sl6py 4 жыл бұрын
Brothers and sisters help me with, the size does not seem to be correct when assembling, what to do ???
@mosand58
@mosand58 2 жыл бұрын
@@ThanhHa-sl6py Sketch on Plane 2: Change 123.83 to 143.83
@furkanors462
@furkanors462 2 жыл бұрын
Thanks for video. but where is the rocker arm we drew ?
@carbon273
@carbon273 6 жыл бұрын
Anybody else having the issue where the rocker keeps flipping orientation when applying the cam mate to the cams on the cam shaft?
@semihbayraktar1015
@semihbayraktar1015 6 жыл бұрын
Yes I have the issue and tried many solution but I cant it
@avinashn9945
@avinashn9945 4 жыл бұрын
did you find the solution
@onyechinezianya9738
@onyechinezianya9738 Жыл бұрын
cool video. But the rocker arm you modelled isn't the one you assembled. Can you look into that?
@HBrooks
@HBrooks 5 жыл бұрын
damn fine job. cool to see advanced mates in action
@zulalkutlu8199
@zulalkutlu8199 2 жыл бұрын
One of the rocker arm parts is missing. so I couldn't finish the rocker arm. Everything I've done has gone to waste. Could you please share the technical drawings?
@karthik.max4450
@karthik.max4450 3 жыл бұрын
Finally finished it completely within 4 days...some dimensions are wrong in the video but still made it successfully
@mayanksinghal273
@mayanksinghal273 3 жыл бұрын
Hey! I am starting to work on this model, can you please tell the exact points of dimensions which needs correction. I will wait for your reply.
@ongnguyen9722
@ongnguyen9722 4 жыл бұрын
in the piston, 50.8+12.7*2 = 76.2 , why look it bigger than the circle 76.2 in the right ??? i'm so hard to understand. 4:06
@mohankadam542
@mohankadam542 2 жыл бұрын
Hi Sir..... is your name Harsh Donde??
@mohammadhoseinmohammadi6890
@mohammadhoseinmohammadi6890 3 жыл бұрын
thanks for this amazing tutorial but part 1 in rocker arm assembley , dose not exist in tutorial!!
@kareem1728
@kareem1728 5 жыл бұрын
how can i create the lofted cut from 1:10:40 in CREO 5.0?
@olalrighty2437
@olalrighty2437 5 жыл бұрын
Try using a swept blend cut.
@kushagraroy5081
@kushagraroy5081 4 жыл бұрын
Contact me for V6 Engine drawing Email- kushagraroy1@protonmail.com
@MrBhavikpandya
@MrBhavikpandya 4 жыл бұрын
Hi SolidWorks Tutorial. Thanks for making such a great model for practicing. But I am surprised in the Exhaust Manifold section at 01:37:03. when we choose bose extrude of Sketch 1 (contour 1) it gave an error of thin feature! Why!! So we extruded it in opposite direction and then modified it in the desired direction. and bang! it worked! I am surprised how did it work! I would appreciate if anyone can explain why it happed and how it just worked when we modified it later? Thanks, Bhavik.
@lono4.631
@lono4.631 8 күн бұрын
In solidworks 2024 rocker arm issue is not showing make sure rockeram role is been fillet
@corymohill-smith4380
@corymohill-smith4380 5 жыл бұрын
Great video, but sad about the camshaft gears ending up floating.
@ashishkumar7378-c8z
@ashishkumar7378-c8z 4 жыл бұрын
Learn AutoCAD Sketches, Drawings, Double Bearing Assembly , Engine Assembly, Fixtures Assembly, Wheelrim profile , and other Cad Softwares in very easy way #ASTALKS Subscribe to our channel for learning CAD(AutoCAD, Solidworks,Creo, Catia, Revit Architecture, 3D Max, Staadpro, Ansys), Computer( All Course's), English, Music, Tution, NTT.
@oz5750
@oz5750 3 жыл бұрын
.
@oz5750
@oz5750 3 жыл бұрын
@@ashishkumar7378-c8z ,., ,,,
@dreamrestore213
@dreamrestore213 3 жыл бұрын
No adaptive spring compression on the valve springs..?? The spring is just pushing through the seat when the cam lobe hits.
@galadler34
@galadler34 6 жыл бұрын
What are the outer sizes of the complete engine? Or how can I see or measure the sizes?
@kushagraroy5081
@kushagraroy5081 4 жыл бұрын
Contact me for V6 Engine drawing Email- kushagraroy1@protonmail.com
@kaidenwhaley7646
@kaidenwhaley7646 4 жыл бұрын
@ColdPetRat2.99 hey man I know it’s been a long time but what are the dimensions of the outer engine?
@pratiksharma4002
@pratiksharma4002 2 жыл бұрын
The rocker arm you have created at 57:19 is different and the one you are using in assembly is different at 1:01:20 please show us how to create that one
@automatix09
@automatix09 4 жыл бұрын
even if there were a few problems it's possible to solve them. THANK YOU for your great work! Helps me a lot to lern new features for school (technical school). If you read that- have a nice day ;)
@cemilcan1872
@cemilcan1872 3 жыл бұрын
can you share techical drawing ?
@anton.saikin9837
@anton.saikin9837 4 жыл бұрын
Good job!!! Where can i get or find sizes for parts?
@MechanixVita
@MechanixVita Ай бұрын
The rocker arm screw width is higher if look through a sectional view can see it clearly
@MechanixVita
@MechanixVita Ай бұрын
1:27:26 over-defined 146 and 387.35 can't be put as a dimension using a midpoint relation. What should I do?
@quantumshadow4218
@quantumshadow4218 6 жыл бұрын
this what i need great video and channel!!! im an engineering student and im gonna buy parts for my new cad computer but im searching about professional gpu and cpu you can give me some advice or at least tell your hardware configuration? im gonna work in a full turbofan airplane for my thesis
@300ml_brasil
@300ml_brasil 6 жыл бұрын
kzbin.info/www/bejne/fV6cYaR7f6aJobc
@3Diest
@3Diest 2 жыл бұрын
Solidworks is amazing software, but you should also Checkout my playlist in Fusion 360.
@grominwithgreg1401
@grominwithgreg1401 9 ай бұрын
Thought I'd take a crack at this but I discovered you have a component that is incorrect for the tutorial and is not included. The rocker arm body portion you have posted (the first component for the rocker arm assembly) is the wrong one compared to the assembly and the bolt is missing too. It was a frustrating moment to find out 7 hours into this but it is a great model i think. Any chance of a fix?
@lahirudasanayake9550
@lahirudasanayake9550 7 жыл бұрын
please upload detail drawings of the each parts
@rajanbhandari4828
@rajanbhandari4828 6 жыл бұрын
The rocker head is not included in the video tutorial. Can we get the dimension for the rocker head?
@leogonzalez6823
@leogonzalez6823 5 жыл бұрын
kzbin.info/www/bejne/e57Pe2SXoNVrsLM
@mohamedsamiramin427
@mohamedsamiramin427 4 жыл бұрын
the Rocker Arm in this video belongs to another engine "Tutorial #260"
@kathirvelmuruganandam7214
@kathirvelmuruganandam7214 3 жыл бұрын
Brother, Where could i find the required Rocker Arm
@mayanksinghal273
@mayanksinghal273 3 жыл бұрын
@@kathirvelmuruganandam7214 kzbin.info/www/bejne/e57Pe2SXoNVrsLM this rocker arm is used in this model.
@kathirvelmuruganandam7214
@kathirvelmuruganandam7214 3 жыл бұрын
@@mayanksinghal273 thank you brother
@yogeshtupe274
@yogeshtupe274 4 жыл бұрын
okay the video is great but I had a hard time mating rocker arm and cams. I was able to apply cam mates to few rocker arms but always failed to mate all of them so I had to change the cylinder head design a bit to mount the cam shaft directly on the valves, that eliminated rocker arm completely giving perfect cam mate with the valve springs directly. Also dude if you had only talked a little in the video would have been much appreciated, just watching you video for hours was painstaking. Also when designing the spring i gave external references to the assembly so that they get compressed by the cams instead of just crashing back and forth in the cylinder head.
@akkig1238
@akkig1238 6 жыл бұрын
where should i get pdf file or detailed drawing of this assembly
@cristiankilon1706
@cristiankilon1706 Жыл бұрын
I just adore your videos
@muhammadsidiq8324
@muhammadsidiq8324 5 жыл бұрын
Rocker arm part is missing
@roybautista169
@roybautista169 4 жыл бұрын
Buana tarde!!! Me ayudas por favor en el ensamble que comienza en 1:01:46, a una pieza no le hiciste modelo, es la principal. Gracias
@danyyer4031
@danyyer4031 3 жыл бұрын
kzbin.info/www/bejne/e57Pe2SXoNVrsLM Si aun lo necesitas
@sumuray7731
@sumuray7731 3 жыл бұрын
sabes donde esta el dibujo del tornillo?
@martingaete8098
@martingaete8098 6 жыл бұрын
Thank you very much, I really appreciate all the effort you put in your videos!
@adnanbinamer
@adnanbinamer 4 жыл бұрын
The rocker arm isn't stable at the same place....when it is done cam mate then suddenly the rocker goes down wards and everything was nice❤️
@andariniandarini4468
@andariniandarini4468 5 жыл бұрын
Thank You I Just Love this Channel. I Need to learn Solidwork but difficult to find mentor then i find this
@kushagraroy5081
@kushagraroy5081 4 жыл бұрын
For more help ypu can contact me at kushagraroy1@protonmail.com
@huntergreer98
@huntergreer98 4 жыл бұрын
Solidprofessor is what my college cad course is using
@Mjloverjr
@Mjloverjr Жыл бұрын
beatiful video im completely speechless god bless you
@justamechanicalengineer5721
@justamechanicalengineer5721 4 жыл бұрын
Inspired by your creativity I have also start a solidworks model designing channel. Keep up the good work
@mINGzTH
@mINGzTH 9 ай бұрын
Hi, I love your work :) I am also building this one. I have a question. What is the meaning of (UV) in the file name of some model? How it different from the regular model file?, Thank you
@venkateshbiradar2697
@venkateshbiradar2697 5 жыл бұрын
Plzzz, upload part drawings with dimensions
@b69bevinayverma18
@b69bevinayverma18 3 жыл бұрын
Is there any way for getting the dimensions of individual parts?
@msrgharde
@msrgharde 5 жыл бұрын
Sir plz provide dimensions pdf for all parts..
@frankyu9905
@frankyu9905 2 жыл бұрын
虽然听不懂英文 但柑橘好厉害,随手画一台发动机
@shaikhshaad2887
@shaikhshaad2887 5 жыл бұрын
Thanks for this nice tutorial for best practical in solid works. I may request you to made aircraft angine as soon possible.
@brandonbowen3197
@brandonbowen3197 Жыл бұрын
God damn ❤️fabulous ,I Love you Blessings from Miami, Florida
Solidworks tutorial | sketch Shock absorber in Solidworks
34:44
CAD CAM TUTORIAL BY MAHTABALAM
Рет қаралды 697 М.
SolidWorks RE Tutorial # 337: DC Motor complete video (Project 11)
2:49:13
SolidWorks Tutorial ☺
Рет қаралды 1,5 МЛН
Sigma girl VS Sigma Error girl 2  #shorts #sigma
0:27
Jin and Hattie
Рет қаралды 124 МЛН
Вопрос Ребром - Джиган
43:52
Gazgolder
Рет қаралды 3,8 МЛН
Wednesday VS Enid: Who is The Best Mommy? #shorts
0:14
Troom Oki Toki
Рет қаралды 50 МЛН
Engine Block Casting Production Car Factory Manufacturing
2:01:12
GommeBlog.it: Tecnica e Performance
Рет қаралды 1,9 МЛН
SolidWorks Tutorial #232: Turbo Pump
1:02:52
SolidWorks Tutorial ☺
Рет қаралды 249 М.
SolidWorks Tutorial # 251: differential gearbox (Project 12)
1:07:29
SolidWorks Tutorial ☺
Рет қаралды 340 М.
Understanding Porsche's New Six Stroke Engine Patent
21:57
driving 4 answers
Рет қаралды 2,6 МЛН
VMC programming complete video - vmc machine programming - cnc milling machine programming 4 hours
3:27:09
CNC CAD CAM ACADEMY of SIGMA YOUTH ENGINEERS
Рет қаралды 280 М.
Solidworks tutorial | sketch jet Engine in Solidworks
33:48
CAD CAM TUTORIAL BY MAHTABALAM
Рет қаралды 414 М.
Solidworks tutorial Design and Assembly of Engine
53:11
CAD CAM TUTORIAL BY MAHTABALAM
Рет қаралды 233 М.
Sigma girl VS Sigma Error girl 2  #shorts #sigma
0:27
Jin and Hattie
Рет қаралды 124 МЛН