Spectrum Receiver Doesn’t Work With Castle Creation ESC Properly Why? Answers in this video

[@jbrc1322]

Like some others have said, the procedure to disable avc is done during the binding process. Turning the gain down or making other adjustments from the tx will not fully disable avc. Here's the procedure from the manual if you want to give it a try: When you power on your receiver, press the Bind button 3 times within 1.5 seconds, then IMMEDIATELY press and hold the Bind button to put the receiver in Bind mode. Bind it to your transmitter. That's it! When you switch off and on your vehicle, the Receiver should flash 3 times to show that AVC has been disabled.

[@MaddmaxxxRc]

Wow thanks so much. Worked like a charm

[@reconrc1787]

I have run into the same problem many times. You can do the calibration but you have to pull the trigger right when you hear the first beeps. Hold the trigger back like you did as you power the rc up, release the trigger and as soon as you hear the beeps start, pull the trigger again.

[@apizar02]

Ok there is no problem. There's a sequence. Earl the second the esc starts singing you hold full throttle. If AVC isn't at neutral it doesn't activate the receiver. Once it's active the esc starts to beep, you then start the castle calibration process. 😊

[@earlmoorhead5555]

Castle put out a statement on how to do it as the two companies brand have a conflict as I talk about in a later episode 👌

[@gorillabeartech4577]

This video helped me out tremendously Earl I did what you did in the video because from time to time my DX5C remote and the AR6100 receiver do actually end up un-calibrating from my Copperhead 10 Castle Creations 1/10th scale onroad edition brushless combo. It’s the 7700 KV combo that is rated at 2S-4S lipo. It’s a badass system. I can’t wait to see then numbers that I will hit on my Vaterra/Losi V100 onroad touring car. I have Contact Foam RC Tires on it. 37 shores front and rear 26 mm in the front 30 mm in the rear. I’ve been testing it on 3S just messing around and it’s easily doing 27-32 mph barely hitting throttle. It seems like foams are taking away alittle speed but they’ve made up for a ton of traction in comparison to the stock wheels. The stock Vaterra V100 wheels suck on 3S or higher.

[@dylanwhite6539]

That 7700kv motor will only accept 2s. Going higher will damage it

[@gorillabeartech4577]

@@dylanwhite6539 The funny thing is that the esc claims to be rated at 2-4S lipo…….. I don’t understand castle at times…. Even the castle tech on the phone told me no more then 2S with my tall gearing unless I’m doing 1-2 passes.

[@dylanwhite6539]

@@gorillabeartech4577 yea. It’s basically just a cheaper way to offer that motor with a sensored esc. Makes no real economical sense to make just a 2s only esc, economies of scale and whatnot.

[@dylanwhite6539]

@@gorillabeartech4577 they also sell it with the mamba x 6s

[@gorillabeartech4577]

I AGREE 💯!!!!!!!!!!

[@josephmorelli3191]

I am going CRAZY! I installed an XLX2 &. CASTLE 2028 motor in my OUTCAST 3 months ago. I have run it 2 or 3 times without a problem. Today I took it OUT. Got it all set up…no throttle. Until I saw your video, I hadn’t the slightest idea what was going on. I am using the original SPECTRUM DX3 with the stock SPMSR6100AT…I think? I am going to rewatch your videos, but I am SOOOO confused.

[@njd879]

Daang wow talk about revelation... I have a flysky gt5 with the avc on my kraton 8s with xlx2. I have been having non stop similar problems for the last year also. I wonder if it is just the the avc from any reciever doesn't work well with castle??????

[@earlmoorhead5555]

The avc just get lost or stuck then it doesn’t know what direction the front of the car is or left right side 💯

[@carlosvelazquez4649]

Always a learning experience. Thanks Earl

[@brianwatkins8071]

What if you powered the receiver with a nitro battery pack before powering up esc, after rx connects them pull full trigger and plug esc in

[@earlmoorhead5555]

Idk never tried that , castle creation is AWHARE of this issue and they have a calibration procedure you can use to calibrate it to spectrum, as of now this seems to be the best way or the only way I’ve tried idk if it’s the best way 🤷🏻‍♂️

[@phillip4984]

Earl I'm having this problem right now as I'm trying to get it calibrated xlx2 and spektrum same receiver your using

[@joshherrman3201]

I've had this same issue with my xlx2 and dx3. I know raz posted a video with a xlx2 and avc turned on. I feel like mine bound up when I put it in first and did a castle software update now it will not bind throttle ep's

[@RoostedFilms]

The video just started so Idk what ya figured out but we fixing to find out. I've had decent luck with most my Spektrum radio gear. I've even seen some videos on how to turn off the AVC inside the receiver. Anyhow thanks for the video Eman. Just turning it down on the remote doesn't "turn off the AVC" it's still active just turned down to 0. Maybe try physically turning off the AVC on the recover unit. I burned up a expensive 1/5 steering Servo before I found the video on how to turn off AVC. That said even with AVC off Idk any of my receivers will power up with the trigger at full pull.

[@gratefuldabs9775]

Haven’t finished the video yet but I have had zero problems with the GT5 receiver paired with my castle esc. Cheap and easy. Just a thought. I’m sure you know what’s best far more than me 👍

[@JohnSmith-sq2yo]

My spektum receiver work fine until I did a rebind now I got the same problem as you. I'm going to try and separate RX battery to get the thing binded again with my transmitter. If that doesn't work I'm just going to slap at spectrum ESC I have laying around in there to get it working. Like I said it worked perfectly fine until I went and tried to rebind the transmitter and Rx. Why oh why do I mess with things that are already working perfect???

[@tunaglove]

Hi Earl. Very interesting. I had the same issue with Radiolink avc reciever to a MMX8. Difficult to calibrate. Futaba seems to work best (for me at least) with the MMX8 running a seperate futaba avc module.

[@pitekfimix8782]

What does mean Don't buy CC I have two ESC with 1717 but I was sick to see it doesn't work with spektrum doesn't calibrate with other Just this is shit

[@RoostedFilms]

Maybe try Manually turn off the AVC at the receiver. I have a feeling even with the hard AVC off the recover won't power up at full trigger.

[@jeremycravens6973]

I wouldn't say that castle and spektrum don't work together, because I have the mmx8s esc in my fireteam with the stock receiver (315). I have no issues!

[@earlmoorhead5555]

That why the model is displayed in the video not sure how many spectrum new smart receivers have this avc pause to power up for Safty 💯👍

[@dereknixon6206]

How have the 315 reciever and calibrated my throttle and can’t get brake or reverse

[@floridaboyoutdoors2935]

I guess I am having the same problem with my copper head 10 for a system. I just got it will not allow me to change the brakes setting and right now I have no brakes and also makes a weird noise in the motor every time I power it off I have to switch the wires around on the motor because it will not let me switch the motor rotation through the transmitter. How do I know there were so many issues that you have to dig through to get a proper running vehicle I would not have bought the castle. I do not want to get rid of my AVC the car works great but I have no brakes and it is a speed run vehicle gotta have brakes! Has there been any solution found that will allow you to run the spectrum DX3 with avc? I can even get into programming mode and fall trigger works to select different parameters, but reverse does not do anything when trying to deny a certain setting! I’ve been tinkering with this thing since 5 o’clock this afternoon when Amazon dropped off the ESC to be honest if I knew it was this difficult I wouldn’t have bought the speed controller. I’ve heard such great things about castle right now I’m throwing my spectrum system back in!

[@earlmoorhead5555]

You have to time when to calibrate the controller waiting for 1 second after powering up to hold the button is what ppl have said 👍

[@bladesrc4977]

Hi eral I had the same thing happen to me I called castle and they said turn it on give it a second to start then go full trigger it worked for me good luck

[@Paul0088]

Found this on Arrma Forum ,, Why does my ESC not beep and show a solid red when trying to calibrate with a Spektrum SR6100AT receiver? We have found that Spektrum has added a safety feature that interferes with our normal calibration and manual programming process. Our ESCs require you to power up the ESC at full throttle; the Spektrum AR6100AT receiver will not boot up properly until the throttle trigger is at neutral. The solution we have found is to power up the ESC at neutral, wait for the receiver LED to turn solid amber, then apply full throttle; this allows the receiver to boot up properly. WARNING: REMOVE Pinion gear or disengage motor from spur gear! You must apply full throttle BEFORE the ESC arms (double chime after LiPo cell count), but AFTER the receiver boots up and goes solid yellow. If the ESC arms and then you apply throttle the motor will run! We have found that waiting until the Auto LiPo feature counts the 3rd cell the receiver is operational and full throttle can be applied

[@earlmoorhead5555]

When doing that if you check your full throttle settings there different every time you do this it get it close to full trigger but not all the time and sometimes your loosing that power in the esc you paid good money for as for me best not to pair the two products or calibrate eas on another receiver so you have the correct full trigger number in the data link to that radio before installing this receiver 🤷🏻‍♂️

[@Paul0088]

@@earlmoorhead5555 yea i was thinking use another none avc rx

[@saltydreamsrc2786]

Earl I am going through that right now. I am done. What other receiver can I use. I castle creations XLX2 esc. With same issues.

[@johannjoesten648]

Hey Earl try this out. Turn on the radio then plug in the battery to Rc then right when it starts beeping pull the trigger and it should calibrate. I hope that makes sense. So basically you don’t have to hold the trigger until it starts the boot sequence. That should work… I believe. 👍🏻✌🏼🤟🏻

[@reconrc1787]

100%! That's what I do and it works every time. I posted the same info before I seen your post here. You definitely have to get the timing right but it does work and can be done.

[@earlmoorhead5555]

Does mine run ? Yes is it full trigger nope check the logs and you will see 💯💯

[@wilsonnieves5291]

I was stumped with this also. Castle tech support helped me out. Gave me the instructions and once you get it as outlined above it works perfect. My Data logs show 100%. I have at least 10 cars running Spektrum AVC receivers with all Castle set ups. I’ve had to become very familiar with this but it does in fact calibrate properly if you start the esc and pull trigger about 1-2 seconds after

[@Dos_Rc]

Calibrate the reciver first once that is done calibrate the esc , turn on the esc first with out pulling full trigger, as soon as you see the orange light come on on the reciver pull full trigger then that’s how you go about it and get around the problem

[@TurtleRc]

Try delaying the arming time. The receiver will see the signal and give you time to as rc guy garage would say "Full trigga"

[@rogueFactor]

yes this! Full Trigga Squirrel Garage

[@michaelvankirk3576]

Great video Earl that was actually some good information u are going to help a lot of people out with this video👍👊

[@earlmoorhead5555]

Hope so!

[@henryfoster3212]

This video helped me reset and do my ESC and my controller thank you Earl 😊🙏

[@94Eg2soler]

I run this receiver in all of my speed cars and I run the Castle xlx2. To perform the throttle/esc calibration. Power on the receiver as soon the light on the receiver is solid quickly pull and hold to full throttle. Then continue the esc calibration. Once done you will have avc and full throttle learn.

[@earlmoorhead5555]

Checking the castle link after this procedure the data shows full trigger sets in a different spot everytime

[@glaanon4225]

I would just put the Spectrum 160 amp ESC in there. I have three of them and all three in different vehicles and all of them have the 6100 receiver , and I've had no issues whatsoever Spectrum works very well.

[@steveskolnick6019]

Just found your video. Mine is doing the same thing and I thought the esc went bad. It worked at first then nothing.

[@rogueFactor]

wait what?!i'm trying to figure out what ya did here, Earl brother. i have never had these issues. not once, not ever. i don't actively buy speKtrum SPM receivers but they are good and have some of the lowest latency at distance, so i've used them with castle, hobbywing, reedy, etc. As much as i hate the SLT radios the SLT receivers are fine if you bind them to a DX3 or better, because protocols. Still i've never experienced this problem, that's so weird BUT! i'm still taking notes!

[@earlmoorhead5555]

No one has done a video on this but the problems been around awhile now 👍💯

[@rogueFactor]

@@earlmoorhead5555 huh, i wonder what the deal is with this, i remember one time on a team associated i had to power off and on three-ish or so times, but other than that issue, i've never seen it again. you did resolve the issue so it doesn't need to be done every time it's powered on hopefully?

[@earlmoorhead5555]

It looses bind this happens on most of my 6100 receivers idk why but it like it can’t see the controller anymore been going on for a year now

[@koldwisper12]

I have had this issue with this receiver and castle on a vendetta. Switched to a Hobbywing sct esc old 4s esc same pro

[@zerrickdracing6784]

Well said brother 👏 👍 👌

[@matthewcostner2937]

I had the same exact issue castle told me to power on watch for thr receiver to go soild and at that exact moment pull full throttle and calibrate as normal

[@earlmoorhead5555]

Yes even trying that the data log show a non full trigger setting calibrated into the esc now if I add triggers sub trim to 120% in the controller I get closer

[@matthewcostner2937]

@Earl Moorhead power on watch the receiver it flashes then goes solid then esc arms castle told me to watch receiver when it gets done flashing and goes solid hit the trigger the castle won't arm until the receiver arms and the receiver won't arm at full because of agc bro what you have to do happens fast like I say turn on watch for solid the instant the receiver goes solid hit full throttle the esc will go into calibrate

[@earlmoorhead5555]

I understand 💯but truly to deal with that on every calibration removing this style receiver cover that holds down the steering servo seems it’s better not to bandaid it every month 🤔and the 124 to the 124 signal for full trigger varies doesn’t set t he same number on every attempt seems I just install another non avc receiver and calibrate but when I have to bind another radio because of an issue I’d have to go threw all of this everytime and that what I’ve done this last year and ended up pinching the esc wire to the receiver several time 🤷🏻‍♂️but appreciate you suggesting this 👍

[@matthewcostner2937]

@Earl Moorhead according to spektrum on that the sr6100 don't need a box according to them because it's already waterproof its a shitty fix don't get me wrong brother lol but that's what spektrum says and what castle told me about all those spektrum avc receivers while using castle products

[@matthewcostner2937]

@Earl Moorhead the problem pissed me off so bad I have a brand new never used dx5c and sr6100 sitting and switched to the flysky NB4 and got there now in4r gyb gyro receiver

[@jeremycravens6973]

Put a regular spektrum 315 receiver in it Earl. Im sure you have a couple laying around!

[@dereknixon6206]

I’m running the 315 and calibrated the throttle and I can’t get brake or reverse

[@dylanwhite6539]

I’m stuck with this, EVEN with NON AVC spektrum receivers. Can’t use my spektrum remote with castle escs Period. Guess there was a reason I ditched castle a while ago.

[@PulsewidthRC]

I’m going trough the same issue,2 different castle esc with the avc 6100, it has something to do when calibrating the Castle when you need to take away the power with the switch on and then shut the switch off and then connect the battery again to calibrate when the power is taken away,it loses it bind, so yeah your not going crazy,I have the same issue to the t. And another thing it seems like it takes forever for the receiver to power on

[@Tinkersrc]

Use the 6200 receiver from spectrum there’s no delay also wait 1second before you pull the trigger on the 6100 receiver before you pull it. It may take a few try’s but it will link up you just have to be perfect with your timing

[@Dos_Rc]

Earl, they do work with castle esc I have all mine with castle esc, The trick is as soon as you see the reciver turn orange before the esc finishes its armingdo the full throttle full brake right left but you have to do the calibration as soon as the orange light comes on, on the reciver before the esc finishes arming you start the calibration process

[@earlmoorhead5555]

Not full trigger mine works to but check data in castle link not wide open trigger ? Like I said works but not properly

[@Dos_Rc]

@@earlmoorhead5555 you can’t pull full throttle and then turn on the esc, you have to turn on the esc first while it’s arming you will see the orange light come on on the reciver once you see that light pull full trigger and calibrate, all this needs to happen before the esc finishes arming idk if you understand me

[@earlmoorhead5555]

Yes and watching the data log the full trigger that gets programmed in is different every time it works but is it truly full trigger when the number is low ? And you can’t determine when it will calibrate a low number my rc works I ran it but not getting max power on an expensive esc is not good 💯🤷🏻‍♂️🤔

[@matthewcostner2937]

That's what castle told me to do the the sr6100 and a mmx8s exact same setup

[@cacanjacowans540]

*Pause for a second after powering up then pull trigger* 👌🏽❤

[@Dos_Rc]

Yes that’s what Iam saying , power on first pause wait for the light to turn orange on the reciver and then pull full throttle

[@MdRai_75]

Still..the throttle wont work as full potentially.. Thats y i use sanwa on my arrmas with castle esc.... Or else It wont calibrate normally

[@endosrc]

Hey Earl, unrelated to the video, but did you have any bellcrank clearence issues with your chuckworks drag slash chassi? Im using the traxxas aluminum bellcrank. Also did your stock servo link work? (the one going from the servo horn to the bellcrank)

[@earlmoorhead5555]

I did a build series and I had a few issues in that series just can’t remember them all ⚠️

[@jonvoogd511]

This is really helpful for me. I've been having these types of issues lately with arrma receivers and max6 esc it's like I need another pair of hands and more brain power too figure this out. Thanks bro!!

[@andrewmagro7703]

i wonder if there is a firmware update for either piece of electronics to then let you go around so to speak or by-pass so then you can use whichever Rec to ESC combo you wish with avc or is there someone out there who has written there own upgrade/Hack and gone around this SMART but Not ESC ??? Interesting topic none the less as i now have some RC with spectrum electronics and both with avc .thanks for these videos Earl there ever so Handy to have the Knowledge in regards to the RC products we have :-)

[@alterdcustomrc4512]

No do not go full trigger until the reciever lights up. As soon as the reciever lights up go to full trigger. Castle walked me thru this a year ago. Check the logs to see if you have 10 percent ❤

[@jessewilliamson2408]

I had the same issue with my xox2 in the same receiver in my dbxl e 2.0 it made me so mad I just went and bought a brand new 315 receiver and threw it in there

[@khrisyeet8022]

Great video. Not trying to talk bad about your choice, but I would think you'd be running "high dollar" radio gear. Pretty interesting. I run a flysky myself, but I was looking for best value.

[@earlmoorhead5555]

Not on a basher as the area I run will kill a good radio my futaba is for on road rc cars so I got the DX5C for the bashers 💯👍

[@cornfed2.0t99]

This is odd...I have a spektrum DX5C running all of my rc's with Castle systems, and I have never experienced this issue before. One thing though, I don't have a MMX8S in any of mine. But I can tell you that I do have an sr6100at in one with a Mamba X 6s and it allowed me to calibrate the esc after calibrating the AVC in the sr6100at. Also no issue with a sr6200at and a MMX6S

[@earlmoorhead5555]

It’s the receiver not the radio

[@cornfed2.0t99]

@@earlmoorhead5555 I understand that. You're having trouble with your sr6100at receiver allowing your MMX8S to calibrate. I'm saying I've never had that issue with a Castle Mamba X 6s or a MMX6S and the same reciever. Try rebinding and disabling your AVC by following the procedure in the rcvr instructions.

[@earlmoorhead5555]

Castle has a memo on how to do it the SR line is the older model that works fine but it doesn’t set full trigger correctly in the memo 🤷🏻‍♂️⚠️several ppl have said there calibration proceeder but log show if I wait to pull full trigger till the receiver light comes on it set full trigger in a different spot each time

[@kellycomeaux6322]

I’m actually running spectrum transmitter and receiver with castle creations also and I never could get it to calibrate since fucking day one

[@earlmoorhead5555]

Yes some truly have issues

[@kh40yr]

Shit. I'm going thru the exact same thing with a DX3/SR6100AT and XLX2 Hydra in a ProBoat Blackjack42. Using the above Spectrum RTR receiver and transmitter from the kit. The receiver shows that the AVC is disabled, which makes sense in a RTR boat,,so apparently spectrum made sure the AVC was disabled before shipment???. If Castle would add the option of disabling the bec and just going off a receiver pack, you could have the trans and rec turned on and bound ahead of time, then pull the trigger and switch on the ESC and continue with the quick start routine. Then disconnect that mess, re-enable the BEC, crank it up to 7-8v to the receiver. Maybe, just maybe, a ridiculous stupid backdoor. I have a Dual Density R603FS sitting here NIB, if all that doesn't work. I know Futaba 2.4 stuff goes almost immediately hot as soon as it is switched on. It would outrun the castle esc on startup and prob be fine.

[@Bluecuban71]

Very Very Helpful 💯💯💯

[@Navyninja636]

Increase the ESC arming time to 5 seconds. Hold full throttle after amber light is steady.

[@MrJimmie688]

What if you use a bec or a reciever pack power on the reciever let it do its thing . Take the esc and remove the internal bec power from the reciever plug so you only have signal and ground then plug it into the reciever while holding the trigga and powering on do your calibration after power off remove the reciever pack reinstall the power internal bec wire feom esc back into the plug and in theory it would work i feel . Maybe not .. definitely an unnecessary step to have to do .

[@escobar-rc-sinnerz7108]

Sup with the limitless no speed runs?????

[@earlmoorhead5555]

It’s doesn’t have windshield wipers on the Limitless 🤷🏻‍♂️

[@marcelwunsch5300]

Bind recover like you! When esc is redy to go like in your video in min 1:00. Turn car off and go Transmitter to AVC and turn all 3 to 0%. 100% trigger turn car on calibrate castle esc Turn avc at the point you like and go. Or bind with avc off Ali calibrate castle esc Bind once again & calibrate AVC and And Go bashing go bashing go bashing When avc active you can not calibrate no ESC and I belive much more brands will have problems with this, only their smart esc don’t care about Booth methods work 100% Br ❤❤❤

[@gorillabeartech4577]

The Castle Creations customer service number I called was a funny call….. the first guy who is a Castle Creations tech by the name of Jason I believe claimed that the AR6100 receiver and all Spektrum receivers in general tend to be “freaking crap” when it comes to using them with Castle motors and esc’s…… brushless that is…. Lol. Then I talked to another technician after him and his name was Joe. Joe was very helpful in comparison and got it working for me but then I realized that after 2-3 days of inactivity the v100’s copperhead 10 7700 1/10th system was Un-calibrated all over again. So I watched this video and wallah !!!!!!!…… MAGIC !!!!!!!!!. Now I know what to do…… but it is fucking bullshit that I would more then likely have to keep doing this because I have a Spektrum radio and receiver with a castle combo. My Arrma Infraction V2 doesn’t have any of these issues though because once again it has the Spektrum Firma brushless combo and not an aftermarket like Castle, etc etc. anyways Earl hope you have a good one. I saw your 100 dollar PayPal giveaway….. I could deffinately use an extra 100 lol. I have cash app and Zelle but my PayPal’s been inactive for 13+ years LOL.

[@earlmoorhead5555]

I find most don’t use PayPal as it protects your account and make getting money quickly costly but if you have time it’s a safe way to track money exchanged 👍🔥

[@gorillabeartech4577]

I could use an extra 100 but I didn’t do anything to deserve it lol. I’m out of work currently so it would help but you have helped me figure this issue out with the damn Spektrum stuff man. Now Spektrum with a Velinion setup isn’t much an issue…. It seems that it’s only an issue with castle systems meaning both a castle creations motor and esc combo. I only buy systems that are matching esc and motors from the same company. I don’t like to mix and match Tekin with Castle or Velinion with Castle.

[@Dos_Rc]

There’s a trick to this it’s driving me crazy I wish I could just show you my brother

[@earlmoorhead5555]

Yes here is my Problem over the year it’s been in the rc like this it keep loosing binding like the remote was never hooked up and it comes out of the blue never know when ! Last time I was 2 hours away and having to pull that receiver box watch a light on the receiver with all the fans running loud can’t hear the esc beep out in the dirt somewhere doesn’t seem like this is a good pair to work together spectrum and castle calibration is not a good calibration in my opinion on a basher maybe an rc that doesn’t use a receiver box and you can mount it outside be ok but no basher would I want a receiver not protected from flying debris 👍💯

[@davidpigg3942]

Disable the AVC calibrate the speed controller then reactivate to AVC.

[@earlmoorhead5555]

Still won’t fully disable avc 🤷🏻‍♂️⚠️

[@Soney_Manic]

Had the same issues. There is a post somewhere from castle advising how to calibrate with Spektrum Radio gear. Think wait until receiver light is amber. But I wasn’t convinced it calibrated correctly and ended up switching out the radio gear.

[@mathias4891]

I'm probably wrong in this but I thought that castle had some kind of bypass for that similar to how in Motorsports you have dummy O2 sensors and stuff like that for tricktunes?? Early once again you bring up a genuine head scratcher but to answer your question about others having the issue I think it's most likely that they just say eff this controller/receiver and go to another brand as the solution. Just watching you fuss with that crappy scroll deal is enough for me to have gotten the dually out to run it over about 37 times lol

[@earlmoorhead5555]

Hate that controller

[@mathias4891]

@@earlmoorhead5555 if you are looking for ideas I'd like to see what you think of the new Radiolink. They stepped up into the heavy hitter market with a touch screen and all that jazz . Looks great but not found many decent vids on it they just say the same explaining what everything does and not so much bout how it does in the field. They say it's still good for speed runs . I just hope it works with the old receivers because I've got too much wrapped up in them to just replace.( 11 at 20$ a piece 😱).. just a thought . . Just ready for some warmer weather cause ( among other builds ) I been working on a Vendetta because of someone . . Did like 3 legit pulls with it and immediately started ripping into it and it's sitting with 6s and no spoiler. I don't know how it will do but I'm just using the uprights for stability curious if it will stay planted. . Love what you're doing for the community Early thanks!

[@Norm2120]

If your that into the mamba esc i’d just change out the receiver and be done with it 🤷🏻‍♂️

[@earlmoorhead5555]

Yes 💯👍

[@tomandrews5392]

If I change motor and esc ...Futaba or Flysky ....I never seam to keep any of the stock electronics ...have a pile of new /old stuff Traxxas, Axial,AE and on .. The box I call CRAP...lol

[@earlmoorhead5555]

I tend to run several Vehical at a time so I try and keep separate control for each my speed vehicle all on my futaba as no one runs those but me 💯👍

[@toddo9043]

Let's gooooooo!!!!!!!

[@CoachD386]

Need to get the old model avc Spektrum receiver that 61000 is 💩

[@stevensaid2200]

I took out the sr6110 and put in a basic sr315, the exact amount of channels I need for steering and castle. No fuss at all and I miss exactly 0 features on the fancy rx. I just want the shit to work, no fuss. That is ground zero, if you don’t have that your product is garbage and needs some work

[@jeremycravens6973]

The dx5 rugged is such a turd! Nothing rugged about it! Especially for what I paid for mine!

[@gpgp1750]

It worked

[@cornfed2.0t99]

You may want to try disabling the AVC altogether by doing the rebind procedure and following the disable AVC instructions. THEN try to calibrate your MMX8S. Hope this helps.

[@randythompson1723]

😎💯💯💯

[@MdRai_75]

Still..the throttle wont work properly Thats y i use sanwa on all my arrmas with castle esc.... Or else It wont calibrate normally..😅

[@TheSpeedrunRookie]

🤙🏽

[@earlmoorhead5555]

Notification squad 👍💯👌🔥

[@pat5462pn]

Dumbo radio n receiver solved all my problems

[@earlmoorhead5555]

Most cheap receivers will as there not a smart system no protection from a runaway rc 👌👍

[@jrubjrub82]

Signal loss triggers neutral, no runaways, it’s the smart, fancy schmancy receivers/ transmitters you have to program to stop runaways.

[@jrubjrub82]

Same as traxxas failsafe, and you use those transmitters all the time.

[@jameswaldby4992]

The older receiver will be better

[@jeremycravens6973]

This is why I don't like avc and all that smart shit! It's unnecessary gimmicks. I don't want someone else controlling my rc. I think if you learn how to drive you won't need avc!

[@earlmoorhead5555]

I agree for a basher rc 💯👍

[@jonvoogd511]

First

[@earlmoorhead5555]

Notification squad 👑👍💯

[@nvrmor023]

Read the directions man jeez.

[@jeremycravens6973]

The dx5 rugged is such a turd! Nothing rugged about it! Especially for what I paid for mine!

[@earlmoorhead5555]

Yep