SPEED QUEEN COMMERCIAL DRYER. NO HEAT! REPLACED IGNITOR AND GAS VALVE COILS.

[@bangzoom8180]

This literally saved me $150-200. Much obliged.

[@jab0327]

😃Perfect! Thanks so much. Never considered that the ignitor could be glowing and still not have enough heat to trip the on the gas valves. Time to find the parts now. Excellent presentation and explanation. Thanks much again,.

[@alexthehandyman3494]

My pleasure. Remember ignitors are very fragile. FYI I have tons of videos on speed queen washers and dryers. Please dont forget to like and subscribe

[@louiswhite1445]

I rock with this guy I've been remodeling a house I inherited and I've based a lot of my choices on his videos. I reached out to him for advice on products and he responded quickly. Surprised he doesn't have more subscribers.

[@jinwonjang9199]

thank you so much! saved $300 and time. I just changed the coils and works greatly. Thank you again!

[@alexthehandyman3494]

My pleasure. Thank you. Don’t forget to like the video. FYI I have a couple dozen videos on SPEED QUEEN

[@johnlynch6540]

Very good. I replaced the solenoid gas valves but still no heat. So now I will order and replace the igniter. If that doesn't work I replace the sensor I guess and or thermal fuse. Appreciate the good video...as I own a Speedqueen washer & gas dryer.

[@zekenzy6486]

Great Video. Thank you for sharing

[@rpsmith]

Great video! Thanks Alex!

[@dennisgardner4010]

Great explanation. Thank you!

[@alexthehandyman3494]

Thank you so much!

[@kevinruggerio1796]

Thanks for sharing Alex, God bless and hope all is well

[@sqeekykleen49]

I might add, ohm the coils, if you get continuity on the unplugged coil terminals.... all checks out but no flame the gas valves may be stuck to the valve body. This happens if water gets inside the gas valve... then it is best to change the valve....

[@rolanddejesus8685]

thanks very much sir for sharing,God bless.

[@robertdavis3109]

Alex, my gas dryer does not fire up. It tumbles but the "In Use" light on the top control console lights up Red not Green. Thoughts as to the issue? Thanks -Robert

[@thehustlerscornernyc6403]

Do you offer personal coaching and tutoring for people who want to take your knowledge to the next level?

[@ocielrobledo7066]

Alex tengo mi speed queen dryer de gas y no quiere calentar todo trabaja pero no calienta será el igniter también el igniter si se pone bien rojo pero como que algo no prende

[@cmguitar50]

Hi Alex - When I unplug the dryer and plug it back in, I get dr 04.00 DS flashing and I cannot power up the machine. Any idea what that is? Thanks! It's a residential stacking washer/dryer. It goes off after a while and I can use the machine Strange...

[@alexthehandyman3494]

1Hello. Im sorry I dont have a solution for you. Im not familiar with that product. I only deal with commercial simple speed queen. Thank you so much

[@lakuinajadulu1532]

Hello Alex, I want to ask. what is the maximum temperature of the thermostat for speed queen? Because there are a lot of fake spare parts in my country which causes my dryer temperature to be too hot

[@kyongjakim7044]

Hi, So helpful videos. Alex, I have a question for you. How about Speed Queen commercial Dryer model# SDGT09WF ignitor is compatible with 510184 ? Appreciate you~

[@raymondgarcia5928]

How could it be the ignitor if the ignitor was glowing / lighting up?

[@alexthehandyman3494]

Hola Mr Garcia, Next to the ignitor there is device that measures the intensity of the igniter. (the flame sensor) When old or broken the ignitor still glows but not strong enough. If the flame sensor is not happy with the intensity of the igniter it will not close the circuit to the gas valve.

[@whataboutjesus425]

Hi Alex. I have the same machine at home, the ignitor glows, then it fires up, after 10 min the fire stops and the ignitor turns on and off on and off and only some times the gas will relight. Is this how dryers work or should the fire stay on the whole cycle? Please help :). Thank you

[@alexthehandyman3494]

Hello, God Bless!!! What about Jesus? Jesus saves! Look at this video. It looks like the valve coils. Let me know what you think.kzbin.info/www/bejne/aZ6Ukn2nbcuAg6ssi=1wMt3gMGSwBe_KMZ

[@whataboutjesus425]

@@alexthehandyman3494 Haha, Amen brother! Yes He does : ). Alex, thank you very much. I watched that video and I'm pretty sure you are correct! I'll be looking for these parts on the alliance website or a local parts house. Thanks again. I appreciate how thorough you are. You are a GREAT teacher, I followed your trouble shooting very easily. May God bless your business as you have blessed many of us.

[@frankgeorge7951]

Hi Alex, I'm not getting any power to the igniter on my speedqueen dryer. Help!

[@alexthehandyman3494]

Hello Frank, Im sorry you are having troubles with your dryer. You have to trace back where the fault is. Watch this video. Im sure is going to help you a lot.kzbin.info/www/bejne/rKe8ppealtaNeqssi=fvHHO2CoBiYzNoQH

[@frankgeorge7951]

@@alexthehandyman3494 Thanks

[@louiswhite1445]

And I need a new multimeter. What kind is that?

[@romiyatem9994]

Coba pakek yg ini bosqu Tanpa igneter kzbin.info/www/bejne/lZDVqWiVZrOCjtEsi=IetpjmoS4dQ9WZlz

[@juanamaya9129]

Flame sensor

[@alexthehandyman3494]

Hola Juan What are you talking about. Greetings!1

[@juanamaya9129]

The component you have never change...I believe if not mistaken is a flame senor, it insures the HSI(Hot Surface Igniter) is working before sending voltage to open gas vavle...but I like the trick of not removing the bracket...

[@johnlynch6540]

@@juanamaya9129 I replaced 2 valve coils, but still no heat. The igniter glows but no gas flows. I think the problem is the igniter? Does that make sense? I am in a foreign country so parts are a little more difficult to get.