Spellbinders Glimmer Hot Foil with wafer thin dies

[@christinesmith989]

Gorgeous card! xxx💖💖💖

[@finin4025]

❤ I love the idea

[@trudievick2359]

Oh boy, I've finally found someone who likes to keep all the little scraps. And the idea of putting and entire piece of paper behind something never to be seen...can't do it. Thanks for sharing your lovely card and the awesome tips.

[@michelegourd5742]

WOW!!! I have a lot of dies that I can use that way!!! YEA!!!!! Thanks so much for sharing!!!

[@lflines]

I really appreciate your very clear demonstation on using thin dies in the glimmer system.

[@Jancass5]

Wonderful video! Oh, and your voice is beautiful and soothing. Your video was a joy to listen to!

[@katieh200]

Lovely Pia TFS 👍😉💐💝

[@PiaKroghLarsen]

Thank you so much Catherine :D

[@lorrainecragan-sullivan7048]

Thanks for sharing this! Just got a glimmer tool for Christmas and wanted to be able to use supplies I already have

[@PiaKroghLarsen]

Congrats on your new crafty tool 🥳 I really hope you will have fun with the Glimmer Hot Foil. If you want mere inspiration for using ordinary wafer thin dies with the Glimmer Tool I recommend another of my videoes. Perphaps you have already seen it, but just in case here is link to it 😁 kzbin.info/www/bejne/iWSYm6uGhKhpe68

[@lorrainecragan-sullivan7048]

Thanks for sharing the additional link, Pia!

[@PiaKroghLarsen]

Hi Lorraine, just posted a new Hot Foil Technique video with wafer thin dies. I highly recommend this one 😄 I have found out how to get thicker lines/impressions with wafer thin dies 😆 kzbin.info/www/bejne/hIWzq62Ki9eJitU

[@hyljat9243]

Thank You, Pia ❤ Very interesting 😊 And I love Your calming voice with sweet accent 😊 Best wishes from Estonia 🇪🇪❤

[@NancyBrown-b1f]

The green plate goes on first then you psper spacer then the clear plate.

[@suekruse6779]

I just got the Glimmer system and saw your tote with you taping the foil together and putting this on the surface to wait till it was ready to put thru the die cut machine. I had no idea we could do this. Saves lots of shifting and saves on foil waste. Glad I saw this! Thank you! Any more tips?

[@teresacruz1318]

Thank you so much for sharing this experience and tips!!! this helps a lot

[@scrappingranny]

Does the die not cut into your plate

[@ebriggs3498]

That is a good question! I thought she had put down the silicone embossing mat, but when I re-watched it I saw that she was putting down a clear plate. On my big shot, that would cut through the paper and cut the words out.

[@PiaKroghLarsen]

When you work with Hot Foiling there must not be very much pressure. When you run your Hot Foil base through your die cutting machine you must not feel any resistance. This goes no matter if you are foiling with hot foil plates or with wafer thin dies. If you feel much resistance then you might risk cutting into your plate/base.

[@vitazgal9933]

Can a regular Big Shot machine be used with hot foil plates?

[@PiaKroghLarsen]

Yes, in my experience you can also use the Big Shot. I sometimes uses my Big Shot for Hot foiling instead of the Platinum 6 😁

[@vitazgal9933]

@@PiaKroghLarsen Whew......T-you so much

[@judithguthrie7335]

I shall try using Washi tape to prevent dies shifting while going through my Big Shot. Thank you for a great tip

[@euvid1]

Won't laying the die with the cutting side down on the foil machine damage the silicone base when you put it thru the cutting machine?

[@ebriggs3498]

@david: no. The silicone blunts the cutting edge. EDIT: I watched this again and see she is not using the silicone mat. She is still running it thru the machine, but not with enough pressure to cut the paper with the die. Apparently a little experimentation needs to be done….

[@PiaKroghLarsen]

When you work with Hot Foiling there must not be very much pressure. When you run your Hot Foil base through your die cutting machine you must not feel much resistance. This goes no matter if you are foiling with hot foil plates or with wafer thin dies. If you feel much resistance then you might risk cutting into your plate/base.

[@tinabruderer488]

When foiling with the die ithe cutting edge up or down?

[@PiaKroghLarsen]

Hi Tina, when hot foiling with wafer thin dies the cutting edge it up towards the foil. It will not cut through as long as you dont make you sandwich extra extra thick. If you feel the slightest bit of resistance when running the glimmer hot foil machine through you diecutting machine you must stop immediately! 'Cause then there is a risk you might cut through.