Stalling issues fixed! Hemi 06 dodge 5.7 l

Solved problem. 5.7l dodge hemi stalling

[@CircuitSky]

Definitely true about the connectors. I got the famous service 4wd system message on the Jeep Commander I bought. I simply pulled the connector going to the transfer case motor, cleaned with electrical contact cleaner and added dielectric grease like you did. Cleared the code and it hasn't come back on. 4WD system works good. Good advice! 😉👍🏻

[@andrewhigdon8346]

One You Tube guy had his ECM replaced and found out that OEM computers are assembled poorly, using lousy solder, and just bad solder work. It could be that the pins in the computer side of the connectors aren’t connecting to the circuit board properly but sometimes when we disconnect and reconnect it happens to air just right, then at some point it becomes a bad connection again, and I’m sure heat and moisture don’t help. Maybe that’s why some guys have to go through a couple of computers till they find one that’s reliable. Apparently the place in Cary, NC totally refurbishes them and improved the quality of the connections. After massive experience and research here’s the only consistent thing I’ve seen. One time my brother(a one time Chrysler service writer) and I were talking about it and when I dropped my hood the engine shut off. Out of the next 5 times I did it, 4 times it shut off. So I hit the cowl with the heel of my hand with it running and it shut off. Then grabbed a rubber mallet, and if I struck sharply in just the right place it would shut off. But then after disconnecting the ECM and cleaning and die-electric grease and all it didn’t do it again for two months, then came back. I’m starting to think the ECM just needs to be rebuilt or replaced.

[@henryhuddleston9256]

Had a problem with my 05 dodge Ram hemi stalling about a year ago, took awhile to find the problem after trying tps senser, wires, excetra, with no fix. Then decided to check the crank angle sensor on bottom rear passenger side of block , pulled it out and the sensor end that goes in block was cracked, replaced and hasn't stalled in over a year now

[@sparkynm156]

I've pulled magnetic sensors that were covered in metallic debris , cleaned them , reinstalled and worked great.. mainly Vss sensors, even in the Rear Axle Hoisings of trucks. My Monte Carlo had issues, turned out the powersterering pump had a seep and its line runs directly over my oil pressure sensor, it seeped through the rubber gromet seal of the weather pack plug and filled the plug and sensor with power steering fluid.. same with my crank sensor.. Worst problem is people who should Never Install Remote Starts, Car Alarms or Even Stereos.. I was visiting my Dad and his stereo stopped working, It was my almost my last day there. I found the best Car Stereo Sales and Installation Store. I was going to ACTUALLY PAY SOMEONE to install a nice stereo in his car... We were in there for about ten minutes looking around. All the employees and others got excited and went to the shop area... There was a van and they just finished a Huge instal for a competition system... They turned on the ignition and were letting it run, warm up, whatever... before Stopping Our Hearts with The Massive Bass that was about to Impress Us... BOOM ! A CAPACITOR was wired wrong and Exploded.. Windows Went and somehow a fire started, it was Awesome.... I figured they were gonna be to busy after that , so I bought a deck, adapter Factory plug etc.. and I did the deck for him .. I'm just rambling.. but the number 1 fix for car problems... Loose or Corroded Battery Cables... It will also give a Crooked Shop An Open Check Book to Charge You and Claim the problem was whatever they want... So I tell people in other states. if your car has a big issue, send your friends car in first with a couple STAGED Basic problems to test the shops Honesty and Efficiency... If they can't figure out a loose ground or no fuel... Then don't let them do a big job, especially if they don't tell you about a loose ground or no fuel... If they say... Ypu need a tune up, a MAF, TB, FUEL PUMP, MUFFLER BEARINGS ETC.. instead.. Punch them in the head and leave.. Ok... Im going to stop babbling... No sleep and no coffee can make for some odd typing.... sigh

[@TheFrenchPug]

I just told a guy to check his crank position sensor on the passenger side down where the transmission connects to the engine. Happened to both of my vehicles.

[@RavenCyclone]

I just replaced my throttle body after chasing this stalling issue for months and now it's running great but I still need to replace my immobilizer. I also followed this video with cleaning and greasing all the plugs.

[@chrispellman5814]

I replaced my throttle body 3 times. Ran great for about a month. Started stalling again. Found out it was a transmission problem. 700 code. Won’t show up on dash. But it will with a good scanner.

[@RavenCyclone]

@@chrispellman5814 oh damn, well I got mine up for sale, hopefully someone will buy it, I'll never buy another Dodge.

[@RavenCyclone]

@@chrispellman5814 thanks, right after I read your comment mine started acting up again, f this car.

[@RavenCyclone]

@@chrispellman5814 can you tell me the exact problem?

[@garpikemike1]

My 2011 ram 5.7 stalls when i come to a stop. Starts right back up with a ping. Always when i come to a stop or am shifting reverse to fwd. It almost feels like if u stopped a manual tranny vehicle by hitting the brake only. But...no codes for tranny. Also seems to run rough when cold. Im not 100% but i have the no traction control light on as and the red brake fluid low light on amd its possible it all happened nearly at the same time. Ive been to countless forums. Nobody knows. If im on the throttle she runs like a top. Slow down at a light... boom...dead. also.. i may be dreaming in technicolor but it seems to worsen as the tank isnt full. Below half it seems much worse. Anyone with an idea would really help me if they could reply.

[@usermrright3865]

If your 5.7 is stalling on you you should definitely check the maf sensor

[@TheFrenchPug]

You should also check your crank position sensor and your cam shaft position sensor if it has one. These are exposes to extreme engine heat and crack and fill with oil all the time.

[@meezee894]

he said that they were all changed

[@bigtae6692]

I have a stalling issue with no codes and nothing work tune up, 2 feul pumps, throttle body, map sensor and pcv vail nothing worked so dodge has a lifetime warranty recall on the feul tank bcuz of the shut off value gets stuck that ended up being my stalling issue

[@mguerrero8787]

I had problem with a hemi engine stalling at stop lights and what my problem was low transmission fluid

[@mguerrero8787]

@@anonmachina true

[@joevargas8433]

What about when you have to put your foot all the down to started it I'll stay on but when put in gear it dies out

[@rdavila26]

How about keeping your engine bay clean .. my car did all this . Turn out to be the evac valve, nothing else .

[@ralphdelgado3815]

Thank you for the video and advice. My problem also started after a big heavy rain and hail storm here in southern California. Luckily the problem started at home the following day. Replaced the O2 sensors and PCM. I'm at a lost. Did you also do the connectors to the O2 sensors?

[@chrispellman5814]

I replaced the o2 sensors. It still had same problem. Check all your wiring.

[@RavenCyclone]

My 06 Charger RT will start most the time but the problem is the anti-theft system comes on so it stalls out and it keeps doing this and I can't find anything anywhere on how to disable the system or fix the problem! 😞

[@392nightrunner]

I'm glad I live in the desert, no moisture

[@MrSpongebob313]

I know this video is old but I know someone else is watching this at this moment , how do I clean the plug? With a tooth pick or something ?

[@ericcarlson9905]

Spray it out with an electric contact cleaner

[@ericcarlson9905]

Then let dry before plugging in

[@kushsmoker5072]

Why not just replace the whole wiring harness that’s what I’m doing I’m doing spark plugs,coils ,ecm and the wiring harnesses already did my motor mounts as well cause I’m having stalling issues hopefully that fixes the problem when my mechanic is done

[@trillestshooter]

Did that work

[@PawlDunken]

I wonder if thats the problem I'm having 🤔 06 charger rt I just got cammed but it did stall one time before the install, plus all my dash lights illuminated flickers sometimes

[@SRT_ANT]

Get it fixed?

[@704SHOOTA]

Where do you buy the throttle body cables at man I’m having the same thing literally baught everything you did now Idk what to do

[@richkidjay8193]

I got a 2006 Chrysler 300c I just ordered a pcm hasn’t came yet but my problem is the car shuts off just in rain rainy days but perfect in sun? Do you think pcm and what else?

[@elifire4147]

He's right.

[@Edandpuppy]

always have this problem when it's hot outside then a cold front comes in with rain

[@Finlandgeography1]

its an old post but i have a 2006 300c dang thing is pulling p0700 u0100, I'm defiantly gonna check my connections this weekend same issue one day it runs and drives perfect next day itll stall 3 or 4 time then runs perfect hopefully its just a connection 😂

[@d.i.yjones507]

Yo chris go video bro ganna try to do what u did but do i put the pcm exactly how it was or did u say just lay it in there

[@ebbefg2229]

That makes more sense

[@craigkhalil3889]

I’m having the same problem right now, I replace coils, sparks plugs, EGR valve & did oil change and air filter change I’m getting P2303,p2305,p1128,p0300 what should I do?

[@chrispellman5814]

Craig Khalil check your battery. And front fuse box passenger side under hood. Check all connections

[@luissanchez-bx9vq]

Clean the throttle body

[@dustinhoots1869]

Same problem. Replaced the alternator, plugs, fuel pumps, full motor, o2 sensors, cam sensor. Maf sensor. I'm losing my mind

[@Realofficialdee]

@@dustinhoots1869 figured it out,

[@jaiholidae1977]

Everybody here got a magnum 💪🔥

[@joegibbs3222]

2005 RT and a 2006 SRT8

[@towninvestment5403]

Just got a 06 Dodge Charger 5.7L 290,000 ran good for like three months then all problem broke lose. I change the Egr Radiator Thermostat temp sensor Air intake Throttle body. I don't no what to do! Its ugly right now! What u think I should do? I was goin to do the PCM all coils and plugs next. Help Needed!!!

[@chrispellman5814]

Town investment battery and pcm at the same time.

[@chrispellman5814]

Town investment also check relays and fuses in engine passenger side box

[@sheltonmorgan68]

Hey chris I have the same problem but it also goes into a mode where I can't go over 20 some times

[@sheltonmorgan68]

Also the codes I'm getting are U0100 and PO748

[@chrispellman5814]

Shelton Morgan check your battery . and front fuse box for loose connections. Failing battery causes this

[@sheltonmorgan68]

@@chrispellman5814 Thanks going to try to fix today and will let you know how things went

[@jesselopez9903]

Did u ever fixed it Shelton my car only does 20 and shakes bad

[@chickensanwich3989]

@@jesselopez9903 probably limp mode

[@dreamteam8626]

05 Dodge Durango hemi stall out diagnostic code p0562 p1684 p0700 any help

[@sweetmtnlotus1328]

I have a 2006 Dodge Charger with Hemi. Recently hit 100,000 miles.

[@djjohn1714]

its an old post but i have a 2006 300c dang thing is pulling p0700 u0100, I'm defiantly gonna check my connections this weekend same issue one day it runs and drives perfect next day itll stall 3 or 4 time then runs perfect hopefully its just a connection it seems to only do it when it rains or its wet out 😂

[@chrispellman5814]

Check all connections to transmission and pcm 700 is transmission codes

[@djjohn1714]

@@chrispellman5814 seems although it fixed my issue went through all the grounds pcm harness and the transmission harness and it hasnt shut off on me since yesterday hopefully it stays that way 😂 thank you

[@trillestshooter]

That Still work?

[@djjohn1714]

@trillestshooter no, unfortunately it worked for about a week and started acting up found out the seal on the transmission harness it broke and the sockets filling with atf I think that's my issue

[@beautybar6844]

Thinking of buying one 165,000 miles on it.. looking for reviews and known issues

[@casinocali704]

Beauty Bar stay away nothing but trouble

[@Realofficialdee]

@@casinocali704 got mine at 207k. Been cool

[@roberthorry2414]

I have an 06 300c and the car won't shift out of first stuck at 30 manual shifter not shifting it doesn't stall though any suggestions

[@chrispellman5814]

Disconnect battery for a hour BOTH CABLES POSITIVE AND NEGATIVE

[@captainobvious5993]

I'm having problems with the mds a code p1416

[@itsjayrock6619]

I got a 2006 Chrysler 300c it shuts off when it rains what could it be?

[@chrispellman5814]

Jayrock Famous check for water on pcm connectors

[@gerryvancedaniel6471]

Did you replace PCM with or without codes??

[@chrispellman5814]

Gerry Daniel yes it was t throwing Codes. Check battery also

[@gerryvancedaniel6471]

@@chrispellman5814 ok thanks, again!

[@MegaDeewilliams]

What the grease call

[@latoyaanthony2888]

Hey I don’t have any codes or check engine light but im still stalling. Any help?

[@chrispellman5814]

No codes or not. Check your wiring. I had no codes at first also

[@latoyaanthony2888]

Okay will do..

[@freddyfox5444]

Did you get stalling after a cold start up? Mine is saying it lost communication but nothing else. My mechanic can't seem to figure out the issue.

[@chrispellman5814]

Leo Leo after I put die electric grease on ports I never had a problem again.

[@chrispellman5814]

Leo Leo it’s in the wire plug connections on computer.

[@freddyfox5444]

@@chrispellman5814 Did your car run fine after initially stalling a couple of times? Mine just seems to stall before it warms up/ move the car.

[@chrispellman5814]

Leo Leo sounds like you’re have a EGR problem or temp sensor issue.

[@chrispellman5814]

Leo Leo but mine would stall while driving or at a red light . Got a new pcm and still did it. Finally put di electric grease on pcm ports and took off bracket and laid it in here so wires weren’t stretched

[@chudlives7570]

Glease, lots and lots of glease....

[@eazy4570]

I have an 07 ram 1500 5.7l. Anyone on here having trouble with the mds system? I replaced all 4 mds solenoids under the intake manifold. Still throwing the same code. P3497 cylinder deactivation system bank 2. Also did a fresh oil change as well. Cleared the code and it came back

[@ericcarlson9905]

It's the lifter

[@ericcarlson9905]

Did you fix it?

[@eazy4570]

@@ericcarlson9905 yes. I took it to my mechanic and he downloaded a software to deactivate the mds. So the truck just stays in 8 cyl mode now instead of deactivating to 4 on highway. Honestly the gas mileage didn't seem to be affected at all. At least not enough to notice. He charged me 200 dollars to deactivate it. With the newer dodges you can deactivate it manually with the features of the truck or with certain performance programmers you can. Unlike with my year model you have to download a certain software and deactive it that way. Its been deactivated for about 8 months now and the truck has been running just fine

[@eazy4570]

@@ericcarlson9905it wasn't a lifter. Pretty soon though im going to be doing a cam upgrade and replacing all the lifters anyways. Along with all new head, valve, intake and manifold gaskets and getting a custom tune. I guess you would consider it a top end rebuild. Pistons and rings look 👌 the block itself is in great condition. Ill probably go ahead and put a newer transmission in it when I upgrade the engine. Its a project truck. I focused alot more on the cosmetics of the vehicle first. Im getting a cadilac cts v cause its time for a new whip. Then it'll be time to start taking the oll dodge apart and doing some upgrades

[@pharaohcam7377]

Hey i got a 2006 dodge charger 212,000 miles and its having trouble starting any suggestions?

[@seankent2036]

Factory recall on the gas tank

[@ericcarlson9905]

Crank sensor?

[@braaaapbrothers2974]

Hey my06 Dodge Ram 1500 5.7 v8 still stalls after I cleaned these wires and sprayed them

[@chrispellman5814]

Braaaap Brothers put in dielectric grease in connectors

[@braaaapbrothers2974]

Chris Pellman okay I will do that to every connector tonight

[@chrispellman5814]

Braaaap Brothers i also recommend disconnecting BOTH battery cables from the battery for 30 minutes. Disconnect the 3 connectors from the computer and put on dielectric grease and reinstall. Then hook up battery. Turn key to on position for 5 minutes but don’t start! Let computer reprogram itself. Turn key off then start.

[@braaaapbrothers2974]

Chris Pellman okay awesome thank you so much, I will let you know if it fixed it, I really hope it will!

[@braaaapbrothers2974]

Chris Pellman hey unfortunately this didn’t solve the problem, maybe I have missed some connectors?

[@sweetmtnlotus1328]

I desperately need help my son-in-law change the PCM it's still stalling.

[@luissanchez-bx9vq]

Tresa Sampson clean throttle body

[@luissanchez-bx9vq]

Tresa Sampson mine kept stalling I cleaned the throttle body it hasn’t happened again

[@sweetmtnlotus1328]

My son-in-law removed the throttle body and cleaned it and put it back on, still stalling. I can drive down the road and it likes it clicks to shut off but kicks back on, never had a car do that before. It's got people stumped here. The check engine light has been coming on from time to time, but depending on how she's feeling it goes off. For a 2006 it's still a beautiful car and I hate to have to get rid of it. I just need help.

[@Abdulaziz5777]

@@sweetmtnlotus1328 have you figured it out?

[@armaniwilliams9341]

Try installing new wiring harness

[@rybuckets562]

I recently got my 2006 Chrysler 300c 5.7 hemi and it’s been driving great for the last past 4 days and then I decided to fill my tank up and then it started stalling out of nowhere and felt like it was about to die. Any help ?

[@chrispellman5814]

Ryan Gerald gas tank is under recall. Get it replaced.

[@Raul54057]

Dont fill up all a way , put only about $ 25.00 dollar of gas dont go full tank

[@edsmith018]

These have a gas tank issue if it has not been replaced. The stalling occurs only after you fill it up all the way. I just make sure not to fill mine up all the way and it was fine until it started stalling out for a different reason I have not figured out yet. www.challengerforumz.com/threads/tsb-gas-tank-2005-2006-lx.103318/

[@skrillawrld]

Ry Buckets bro I accidentally overfilled my gas tank about 4 months ago and when I drove home right after, the oil pressure light came on and the engine cut off. My car was sitting for the 4 months it wouldnt stay on longer than 10 min. I recently started driving it again a month ago and it hasnt turned off I have no clue how if I didnt get it fixed but the gas finally went down and I havent had an issue

[@seankent2036]

Factory recall on the gas tank

[@rko619wrestlingfan]

were you getting codes P0700 U0100?

[@chrispellman5814]

Rewindto91 p700 yes

[@edsmith018]

I am getting these same 2 codes on my '06 Magnum RT AWD and have cleaned the pcm connectors, throttle body, and changed spark plugs and coils but it still stalls out. It is like the computer is disconnecting and then coming back online. After it stalls it takes a few seconds to kick back into gear after I start it up. Are you experiencing the same issue? I'm getting tired of throwing money at this car for an issue that is so hard to pinpoint.

[@chrispellman5814]

Rewindto91 yes. I replaced same parts. Didn’t help. That’s when I bought a rebuilt pcm and put dye electric grease on the pins and connectors. No problem since. Also check the load on your battery

[@theboss9975]

@@edsmith018 I have an 06 charger r/t. Mine is doing the same thing. Shuts off, but starts up. Then takes a few seconds to catch gear. Have you fixed the problem. I would like to know. I just put a brand new engine in it. But the problem started with the old engine. Please let me know. Very frustrating. Thank you.

[@edsmith018]

@@theboss9975 Unfortunately, no mine still sits unfixed as well. If and when it is figured out I will tell you what the fix was. I am leaning towards it possibly being a connection problem with the PCM, but I have not been able to verify this yet. If you manage to get yours fixed, please share that fix with me as well because I can't wait to start driving it again. Good luck, it's disheartening to see so many people with this same issue.

[@christiancordova8915]

Egr valve

[@chrispellman5814]

No. I replaced that. It still happened

[@christiancordova8915]

@@chrispellman5814 did you change the PCM

[@chrispellman5814]

@@christiancordova8915 yes. Twice.

[@chucho32922]

Replace the motor?

[@moparguy9410]

I replace mine and still stalling too

[@ericcarlson9905]

@@moparguy9410 did you change the crank sensor?