How do you handle synchronisation between the incoming SRT feeds?
@StreamoutAU9 күн бұрын
It is a non issue. I usually run 25 frames per second so a single frame is 40 milliseconds and I have never witnessed even a 1 frame variation (unless I haven't configured something properly!).
@Demotiv Жыл бұрын
Thanks for sharing! Actually you could even access the kiloview web interface through pep link VPN. Even working with srt in VPN if you have one in your hub! I'm curious about how do you set connections priority in peplink. When using venue wan I tend to put 4gs in second priority because of the latency difference!
@markhepi7791 Жыл бұрын
Nice work. Great setup
@louisrubera2589 Жыл бұрын
Great Video, Can you make a video Detailing the Pepwave Boxes? Or possibly list the components inside? That would be very helpful.
@StreamoutAU Жыл бұрын
Hi there. Yes I have had quite a few requests for this topic. It will probably be my next video.
@louisrubera2589 Жыл бұрын
@@StreamoutAU Awesome I appreciate it very much!
@kishpro7368 Жыл бұрын
Great video. Can u do a video with the bast peplink setting for streaming?
@claudiocohen2709 Жыл бұрын
Same. Would like to know best configuration of speed fusion tunnel for SRT.
@lapoguidi Жыл бұрын
Thanks for sharing this great setup. Could you explain better something about the battery stage? Self-made or a commercial one?
@StreamoutAU Жыл бұрын
Hi Lapo. I built it myself using parts from Meanwell and the battery sleds a from Ebay.
@lapoguidi11 ай бұрын
Hi Simon @@StreamoutAU, I had some free time to try to figure it out with Meanwell Powersupply PSC serie, but I have some troubles to safely connect it. If you want and if you have the time, can you take a couple of photos of the inside content of your boxes? I have a single Balance 20x and I would like to use with a powersupply or battery when I'm outside. Thanks anyway.
@jackbarraball12539 ай бұрын
looks great. one question. how are you handling the audio return feed ? is it coming in on one of the io cards ? am looking to build myself something similar and the audio return is something i'm struggling to find a solution for
@StreamoutAU9 ай бұрын
Hi Jack. Yes it is coming from the 3.5mm audio jack on the Decoder board. I’ve installed a pair of balancing transformers in the rack so that the output is isolated as well as balanced.
@jackbarraball12539 ай бұрын
@@StreamoutAU ah that makes sense , was just unsure if there was a separate encoder/decoder handling the audio. and i take it you'd have the opposite for audio in to take in a feed from a venue on the encoder side if they have a local mixer which their microphones were being plugged into ( if you were not on a vmix call) out of curiosity . did you look at running a simple dante line instead of running the balancing transformers?
@kamileqone Жыл бұрын
Do you have any solution to delay input video for SRT co cut out last 1 second when we lost signal to not see that on Program out?
@IgnacioMadero Жыл бұрын
How easy do you find making SRT calls through cellular networks? Since you cannot do port forwarding, how do you manage it? Are you using an SRT gateway?
@StreamoutAU Жыл бұрын
Hi Ignacio. Because my control room has a static IP address, it is simply a case of configuring the Kiloview boxes to call my control room. In my control room, I have some ports forwarding to the Vmix machine and it is in listener mode.
@IgnacioMadero Жыл бұрын
@@StreamoutAU thanks so much!
@kamileqone Жыл бұрын
For what use cases you are using OBS?
@markhepi7791 Жыл бұрын
Great setup! I like to use peplink as a wan for the live u solo pro which encodes the stream rather than vmix. Quality is better
@kamileqone Жыл бұрын
Pity that Kiloview E2 has only H264. New Kiloview P3 will have H265 but this is another device. You do not use SRT H265?