Here is the link to the thread adapter jaxpaverproduc... And here is the link to the entire assembly jaxpaverproduc...
Пікірлер: 35
@wehttamgtrekce Жыл бұрын
Why did not give the new ratios? Why would I buy it if you don’t provide the increase ratios?!
@Tie_dyed77 Жыл бұрын
Because the check valve won’t change the ratio. It’s just more durable. Highly recommend!! Still have to do a flow check but it will stool be anywhere from 8 to 11:1 draw. The injector itself will determine more or less chemicals. 2.0 vs 2.1 vs 2.3
@robertmintz78162 жыл бұрын
So what is the draw from the 2.1 standard vs the supercharge one?
@Addictedtothewild Жыл бұрын
Per this guy “substantially, sometimes”… trust the science 😂
@brandonvining3504 Жыл бұрын
I'm also in Jacksonville. Great video
@noeaguinaga40186 ай бұрын
Dude I have those I bought from ace hardware! If you had those made then that company got your ass!
@j.d.williams6882 Жыл бұрын
Thanks brother, just ordered 2.
@MannyAguilarJr2 жыл бұрын
The general pump threads are probably British BSP or BSPP like their water pump.
@fivestarpressurewashing19412 жыл бұрын
No they are actually 7/16x32tpi
@MannyAguilarJr Жыл бұрын
@@fivestarpressurewashing1941 interesting
@ExpertPowerWash2 жыл бұрын
I ordered a couple. Thanks for the great video
@fivestarpressurewashing19412 жыл бұрын
Appreciate the order!
@hisnameisiam808 Жыл бұрын
Where do I get the check valve?
@davidbelitz76924 ай бұрын
How do you rebuild the check valve when it fails? I'm trying to open it. Very difficult. The rebuild kit is $5 and an entirely new check valve is $28. I just bought a new one and it failed after 3 house washes.
@mattjohnson4479 Жыл бұрын
What is the estimated increase in draw?
@dharam108 Жыл бұрын
my draw rate with this 3/8" check-valve on my SuperSuds Sucker is nearly double what it used to be with the 1/4" ball and spring check-valve
@mserrato5872 ай бұрын
Hi there!! Can this chamical injectors be use it on a hypro pump 2345b-p ?is for a carpet cleaning machine thank you
@johnshoemaker61642 жыл бұрын
The article says substantial increase. Of course every machine set up is going to be different, but can you generalize a percent of increase that we are likely to experience? A range, possibly?
@dharam108 Жыл бұрын
it looks like the Barbs on both injectors are 1/4" - is that right? I put a 3/8" Barb on my new check-valve, and with 3/8" hose I get a very phat draw rate.
@scotthester2189 Жыл бұрын
Just ordered two thanks, btw will these allow me to shoot enough shock to kill mold on bricks and stucco. Or should I use the soft wash system for that? Thanks
@ryacow Жыл бұрын
I’ve got 1 it didn’t work for me. I’ll have to test it out to see if it’s different.
@smitty46992 жыл бұрын
do you need teflon tape or an o ring when you thread them into the injector?
@fivestarpressurewashing19412 жыл бұрын
Yes you will need Teflon
@perezleolp Жыл бұрын
So basically take spring and and ball out and install any 1/4 check valve??
@fivestarpressurewashing1941 Жыл бұрын
Yes!
@hisnameisiam808 Жыл бұрын
@@fivestarpressurewashing1941 does it need to be high pressure?
@watcherwatchmen7785 Жыл бұрын
@@hisnameisiam808 Think about it, it's drawing detergent slowly out of a container. It's suction, not high pressure. So in short, no, it's not high pressure.
@ktpowerwashing2 жыл бұрын
Isn't it just an 1/8" threading??
@fivestarpressurewashing19412 жыл бұрын
No, it’s 7/16x32
@Ellipsis-101 Жыл бұрын
Nice
@InfinityCleaning Жыл бұрын
Do you happen to know offhand if these also fit the newer GP kynar/stainless proportioning injectors? The weakness on those seems to be the o-ring blowing out, as well as the plastic barbs sometimes cracking.
@fivestarpressurewashing1941 Жыл бұрын
As far as I know those injectors are different
@hisnameisiam808 Жыл бұрын
@@fivestarpressurewashing1941 where do I get the check valve?