Suzuki Boulevard C50 shaft/final drive replacement and disassemble (worn splines/ gear)

How to remove Suzuki c50 rear wheel
• Suzuki boulevard c50 r...

[@ronaldadventuresantos7220]

Wonderful, thanks for the video. I love Japanese motorcycle. I love that you have tubeless wheels

[@josephharris1869]

Thank you brother !! Putting mine back together today

[@rocxylemmon8535]

Thankbyou for this! You have a great spirit to do this to show us how to keep these bikes on the road.

[@mccslawg]

Thank you! Great video. I have a 2014 C50 BOSS. I love this bike. Your video I will save if and when I need to take on this job

[@abelgonzaslez2103]

SO GREAT THANK YOU MUCH .

[@jnetane]

Great video! Thank you

[@pd8559]

Most excellent video. Other than the final drive what else has typically needed replacement by 30k miles?

[@Yololife813]

I would check drum brakes, front brakes, coolant, bleed brakes, if clutch seems to slip relplace that too, spark plugs. Basic maintenance. Owner manual can be found on website.

[@AlexandreKlafke20]

Thx for the nice vídeo!

[@alisaleem6988]

Here you can explain how to open and change the clutch valves of a Susuki Boulevard C50 2007 bike.

[@JooKed]

Question, how did you get the female coupling holder nut off? I'm talking about the one with the folded lip you need to pry open, but you need to hold the assembly in place to take the 22mm nut off, how did you manage? Vice?

[@Yololife813]

I used my impact wrench

[@keithnguyen1436]

Excellent video. Where did you get the whole final drive assembly and how much if you don't mind me asking?

[@Yololife813]

eBay. I think it’s $100

[@ChristCostanza]

Where did you find the whole final drive assembly like that? I am having the same issue and I'd like to replace every like you did, but the only whole assemblies I've found have the same issue...

[@Yololife813]

eBay

[@robinson_crusoe_]

Hi there 👋. I start reassembling all of this final gear unit yesterday and had a question. Maybe you know how that bond 1207B should be applied? There are 2 holes for breather on final gear case. Thank you.

[@Yololife813]

Sorry I don’t know how’s that bond or how to apply it. I just replaced the entire shaft drive.

[@olheghtt]

It looked to me like there were five bolts to remove that frame + the one bolt with the hex head, do those six bolts have a torque spec or do they just going tight with blue thread lock... Same question for the three acorn bolts.

[@Yololife813]

I believe They all have torque specs. You can Google it I just hand tight them.

[@olheghtt]

@@Yololife813 I'll double-check my service manual, Haynes manuals are not all that well written.

[@wesrutkowski5564]

I have exactly same problem , when you received the new drive shaft assembly was the shaft firm and not loose and wobbly like what you showed on this video?

[@Yololife813]

It was loose but not much like the one on the vid

[@wesrutkowski5564]

@@Yololife813 thank you

[@alisaleem6988]

Where is the predecessor of the engine operating, Susuke Boulevard, opening and installation diagram

[@alexandremiro]

Great video ! How long it took you the whole thing ? I see you take off your pullover while putting back the shaft in the yoke (that drop down a bit) and the video is cut. How did you do it ? Thank you

[@Yololife813]

Took me little over 5 minutes get the shaft in.Just have to rotate the shaft and angle down. It will go in eventually

[@alexandremiro]

@@Yololife813 Thank you !

[@alexandremiro]

@@Yololife813 And what about the whole thing ? How long it took you more o less ?

[@Yololife813]

@@alexandremiro probably little more than 2.5 hrs. If I did have to do the video, probably 1.5 hr

[@alexandremiro]

@@Yololife813 Thank you !

[@collosus81lash98]

Good video. How many miles do you have on it?

[@Yololife813]

30000miles

[@madhanakumar6155]

Nice video clearly briefed fr replacing final drive shaft. Where is the EBay need full address & contact # for my future requirement if any. I own c 90, boulevard is good bike from Suzuki.

[@Yololife813]

eBay app you can order anything on there. Just do a search

[@user-gb9rf8fk2g]

Great job. May I know the part number that is not working?

[@Yololife813]

I ordered on eBay the whole used shaft. There was no part number. If you need part #go on partzilla.com and look up part number on their site.

[@user-gb9rf8fk2g]

@@Yololife813 thank you so much

[@murcielagosky]

Just today, it happened to my wife's 2009 m50. Question. If you buy a used one from eBay, how would you know that it won't happen a year later again?

[@Yololife813]

You won’t. It’s just a chance you have to take. Ask the seller how many miles is on the bike when the shaft came off. The less miles the better. When you get the used shaft inspect and put grease on the splines before install it. Good luck

[@ronaldadventuresantos7220]

I need to find tubeless wheels for my boulevard 08

[@Yololife813]

Try eBay?

[@mdjones905]

This manufacturer flaw I doubt is accidental, it’s intentional because it’s happened to too many.

[@mikeshaffer2950]

What year is bike? An are those factory rims?

[@Yololife813]

2009 factory rims

[@JW-bw8nj]

It's a C50C

[@motorcyclistfromholland8856]

You overdone it. It’s almost always the splines on the shaft drive itself