How to check your SV650 and SFV650 valve clearances. See More here: lwtracer.com/l... Facebook: @LWTRacer / lwtracer Twitter: @LWTRacer / lwtracer Instagram: @LWTRacer / lwtracer Titanium Racing Hardware lightweightrac...
Пікірлер: 24
@ericdemant9250 Жыл бұрын
You showed how the front came looks but not the rear im struggling to do timing on the rear
@JohnnieV27 күн бұрын
There’s no way my bike would ever run again if I took it apart
@JohnSmith-yg8jk4 жыл бұрын
Great video! Would a out of specs valve clearance make the engine not to start? I have 2000 sv650 that doesn't start at this moment. I have spark, good compression, and fuel. I even tried starting fuel straight into the carbs with no success. In the past it would start right away. Thank you
@LWTRACER4 жыл бұрын
They would have to be wildly out of spec for the engine to not start, that is most likely not the problem as to why your bike won't start.
@docmotoman37553 жыл бұрын
Hey did you figure this out? Having the same issue on my 2002
@kevinsmith39353 жыл бұрын
Great vid mate, do you check sv1000 valve clearance the same way?
@cwg63242 жыл бұрын
Do you have a video to tell the difference between cam chain rattle and main engine bewring or piston slap. Mine doing a slapping / knocking noise from front cylinder.
@trevorjohnsen4303 Жыл бұрын
Find the issue?
@everygirls27195 ай бұрын
can u send link for this box with shims?
@TrustyZ9003 жыл бұрын
When removing cam chain tensioners, do you remove the base with the two screws to the head or just the center bolt , spring and tensioner itself?
@LWTRACER3 жыл бұрын
everything. I loosen the middle bolt first.
@N0nManfiold994 жыл бұрын
How much more work would it be to remove the actual valves themselves and check they're not bent/tapping if cam timing was off ?
@LWTRACER4 жыл бұрын
You'd have to remove both cylinder heads. You'd be looking at a few more hours of work.
@johnmarston21372 жыл бұрын
how many miles did you have on the engine when checking? when was the valve clearance last checked?
@LWTRACER2 жыл бұрын
These are race bikes. Miles are almost never known. I normally only check when building the engine. They get checked again when rebuilding.
@JustDaTips5 жыл бұрын
Why are you ok with the intake valve being at 10 thou if the clearance is stated at .004-.008? First!
@LWTRACER5 жыл бұрын
G it’s a common practice on race motors.
@drstimpy14 жыл бұрын
Negligible change in flow from the reduced lift then?
@SexyKnight013 жыл бұрын
Do you prefer to be on the tight end or loose end on valve clearance?
@jasonb65702 ай бұрын
Loose.
@jyudomassan4 жыл бұрын
@LWT RACER do i have to drain the oil from the engine to do this?
@LWTRACER4 жыл бұрын
nope.
@jyudomassan4 жыл бұрын
@@LWTRACER if only them girls would reply me back as fast as you did🤣 you are a hero good sir. Thanks a million🙏
@LWTRACER4 жыл бұрын
@@jyudomassan Just add to your Tinder profile that you can adjust your sv650 valves and those DMs won't stop coming in.