Toyota Tacoma Needle Bearing Swap for ECGS Clamshell Bushing

Tutorial on the popular ECGS clamshell bushing swap on the Toyota Tacoma.
Clamshell Bushing: eastcoastgearsupply.com/i-853...
Bushing Removal Tool: eastcoastgearsupply.com/i-144...
TOOLS USED IN THIS VIDEO
Prybar: amzn.to/2Gm8gpk
Center Punch: amzn.to/2Zof4LG
3lb Hammer: amzn.to/2DlYCCi
Diff Oil: amzn.to/2DlOLww
Bungee Cords: amzn.to/2Gm8Zqn
35mm socket: amzn.to/2GqRJjL
22mm ratcheting wrench: amzn.to/2IJDjy0
Deadblow hammer: amzn.to/2XvJf1T
Torque Wrench (up to 250 ft. lbs.): amzn.to/2IuZfxM
Hex Bit Set: amzn.to/2IuTccm
Needle Nose Pliers: amzn.to/2IKTACL
Tie Rod Puller: amzn.to/2Iwxi8y
#clamshellbushing #ecgs #toyotatacoma
→Awesome Tacoma Products: www.amazon.com/shop/tacomaholic
→Tacomaholics Anonymous Website:
tacomaholics.com/shop
→Tacomaholic Gear: teespring.com/stores/tacomaholic
→Patreon: / tacomaholic
→SUBSCRIBE: goo.gl/AdMDQZ
→Follow me on Instagram: _tacomaholi...
→ Tacomaholic-...
Fan Mail? Send to:
Tacomaholic
PO Box 2246
Centreville, VA 20122
POPULAR MODS FEATURED IN MY VIDEOS
INTERIOR
AC Knobs: amzn.to/2DChAX3
Tactical Molle Panel: amzn.to/2K4mZXx
Weathertech Floor Mats: amzn.to/2Dle7eB
CONVENIENCE
Grid-It Organizer: amzn.to/2z91al2
Quick Fist Set: amzn.to/2PVXc93
Center Console Organizer: amzn.to/2FmlQvJ
Glove Box Organizer: amzn.to/2TcqmQb
Center Console Tray: amzn.to/2Dj4H3j
Tacoma Bed Mat: amzn.to/2Q1kMBi
Hood Struts: amzn.to/2Dp3nft
MAINTENANCE/PERFORMANCE
UNI Filter: amzn.to/2OI5psI
Fluid Film: amzn.to/2DEyh4i
LIGHTING
2nd Gen LED Kit: amzn.to/2Td2Wu7
Ditch Lights: amzn.to/2Q3bViQ
TOOLS
Trim Removal Set: amzn.to/2TcqaQX
Torque Wrench: amzn.to/2Q3bUvi
Floor Jack: amzn.to/2FlcdNJ
Jack Stands: amzn.to/2DDme7f
Magnetic Tool Tray: amzn.to/2QGv1s0
Sneaky Snitch by Kevin MacLeod is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Source: incompetech.com/music/royalty...
Artist: incompetech.com/
Disclaimer:
Due to factors beyond the control of Tacomaholic, I cannot guarantee against improper use or unauthorized modifications of this information. I assume no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. I recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Tacomaholic, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Tacomaholic.
I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.

[@Tacomaholic]

Tacomaholic hats now available in the Tacomaholic shop with a nice intro discount!: tacomaholics.com/shop?olsPage=products 😀👍

[@jfriday1ify]

I tried the cable method, and I found it easier to just add another set of jack stands under for safety and then take a long flat edge screw driver with a 3 pound hammer and Tap the CV out from under the vehicle on the slotted edges on the CV. Worked well to get it back in as well. Just tap, tap tap and spin the CV a little and Tap some more to overcome the Clip on the axle. I would also replace the seal while you are in there, but this taco was brand new so maybe not needed for this job.

[@DB-we2wk]

Had to do the same on my 4WD Tacoma. I took it to 4 wheel parts to have a 3" lift installed. Afterwards I had the famous intermittent vibration. They knew about it but didn't know how to fix it. After extensive research and watching this video I replaced the driver side needle bearing with the ECGS bushing. You would've thought that a big company like 4 wheel parts would've had the wherewithal to figure it out. Unfortunately not 🤦

[@efil4kizum]

just another crappy hacked slopshop?

[@zathias6154]

Used to work for 4WP as a technician... Do not go to 4WP 😂

[@doughartwell5319]

Dude. I just wanted to say thank you so much and you’re a genius, I couldn’t find a slide, hammer or CV attachment in the stores I had locally, but I could find steel rope a dead blow, and some connectors created one of those styles slide hammer is that you did, and it worked great. Would not have gotten it without you. Thank you.

[@thumperjr100]

I actually took a day off and drove from Northern Virginia to NC to have ECGS actually perform the change with their bushing. Great folks, cost me less than $350 to have them perform that, including bushing, and made sure my rear axle was within spec. 3 degree shim added. Would highly recommend them if able to make the drive. Most professional company. I have 2018 Tacoma with 3 inch OME lift

[@ryanrvaughn]

That is my Truck in the video. I also did the OME lift and 3 degree shims. Rides great. Zero vibes.

[@daledow2278]

The punch in the brake rotor... I was missing that idea. Thanks for that.

[@thomasgjonovich5524]

Or you could also put the wheel back on and lower it to the ground and tighten it that way too.

[@KFloTacoma]

KZbin recommended this video to me too after I uploaded my own ECGS install tutorial HAHAHAHA

[@alexmontoya1955]

How it's only the driver sidd

[@danielborrer270]

You - both - recommended to me- Next weekend- What’s the recommendation on gear oil ? I will replace while doing this anyway

[@stephendouget5515]

I have a 2015 tacoma 4wd, i had lifted the front 1 3/4'' in front with bilstein shocks and noticed a roaring noise coming from front diff. Replaced needle bearing with bushing from ECGS and it solved the problem. Also front end would shimmy around 55 mph. Solved that problem also. Definately worth it and did it myself.

[@mariobrcik6920]

was the noise constant or kinda on and off

[@MrYour1Fan]

Just wanted to provide an update tried here what was suggested for the sting wheel vibrations and even though the work was not as easy as in this video. It did correct the problem and I appreciate you for sharing your video

[@scottclukey2424]

A year or so late but it all started with a suspension update and well here I am, Thanks guys yall made it so much easier to pull the trigger and get'r done. Thanks 😊

[@rickm4295]

This is by far the most informative kick arse video ive seen. It really makes this not seem so daunting. I really appreciate this knowledge brother

[@Tacomaholic]

Thanks Rick!

[@forrestbirdwell3900]

Best upgrade ever solved the issue perfectly

[@Tacomaholic]

Glad to hear it.

[@panchog2552]

Great info and detail.I've got a 19 trd sport with a 1" lift and I believe this is the problem it has steering wheel shake at 40 mph.Had alignment checked and rotated tires and still shake.So I will check cv next.Thanks guys.

[@matta5194]

Thx for details and tools needed list! Awesome vid

[@mikelikesknives428]

Seriously, thank you for these videos. You have saved me a lot of money with these how to videos. Thank you for taking the time for us do-it-yourselfers.👍👍

[@Tacomaholic]

Thanks so much for watching Mike! Glad to hear the vids are helping. Tons more maintenance-style vids coming.

[@Delmarksman]

Plus 1 to what Mike said, thank you for your videos! Don't need this yet but is nice to know that it's totally within my abilities to accomplish this.

[@Tacomaholic]

@@Delmarksman 👍 Thanks man!

[@glenh4397]

Thanks for this video, super helpful. I'm going to have to do this to my 17 4 Runner as ot has the same issue.

[@davidbuckles9950]

This is one of the best bushing replacement videos I’ve seen. I really like the cable slide hammer idea. Nice work.

[@Tacomaholic]

Thanks for watching David!

[@terrysturtevant8800]

David Buckles I agree!

[@brentgoff8900]

Thanks brother.... great content! Keep on Taco Truckin!!!

[@JtheInvincible]

I just got an alignment on my newly lifted truck and was suggested to do this next. Wish I did it all at once lol. And axle shims next too maybe

[@mikeschoolcraft21]

Thanks for the tie rod puller link , cheap.

[@BastekF76]

That's a great video! Thanks for creating and sharing it.

[@Tacomaholic]

Thanks for watching Sebastian!

[@iismatthew123]

Now that y'all got some practice in we can get mine done sometime!

[@Finallyonair]

Great vid! Thanks for being detailed! Very helpful!

[@Tacomaholic]

Thanks for watching Eric!

[@FK-kr3xs]

Realy like that steal cable and hammer idea. Just did my bushing couple weeks ago, had some problems to pull the shaft out . I wish I would see this before 👍

[@Tacomaholic]

How did you end up getting yours out?

[@FK-kr3xs]

@@Tacomaholic Prying with a large screw driver . Wosn't easy at all:)

[@Tacomaholic]

Lol I can imagine. One of those things that has you cussing in the driveway. 😀

[@SWZ32TT]

I had the low grinding intermittent growl pretty much immediately after lifting my 2nd Gen. looks like I’m ordering some of these.

[@robk6169]

Thanks for the info guys great job,

[@HugDeeznueces]

Nice video! I'd like to see more of this kind. Awesome bro!

[@warsword2538]

That ECGS bushing was the best modification I have done my truck feels smooth and silent. I had been chasing a noise and vibration after a leveling of about 2 inches and now it's so much better 👍

[@TheMffd26]

Did you have any steering wheel shake at 45-60mph.

[@rx8dude907]

My small vibration is after 65mph but kind of subtle and goes away not sure if it’s even the needle bearing

[@jditts]

@@TheMffd26 Is it only at those speeds? Mine vibes between 70mph - 80mph. 1st Gen Tundra

[@Bers3rk_tv]

I'm about to do mine right now.

[@mmunoz5875]

Great video and good information for those that may need it. I hope I never do!! lol🤣😅

[@Rob-pb8tp]

Another great video B! Tell Randall he needs a shave!

[@Tacomaholic]

He's going for the ZZ TOP look. 😀

[@johndaniels9751]

He made that look easy. Now lets see brian do the other side.

[@evanfox1291]

Its a ball bearing on the passenger side

[@jonbakerocbpro8802]

I have some vibrations after a 3” suspension lift and -18 33” tires. Vibration is between 45-65mph. Chances are this isn’t my fix but it won’t hurt. Panning on keeping the truck as long as possible. 2021, 26k miles and paid off.

[@efil4kizum]

27 years a possibility for ya?

[@Tom-ej8bb]

Very Well done!!!!

[@F0X74]

For anyone wondering. I got the new removal tool. The nut is now a 19mm. Not a 22mm

[@mtnbikingjoo]

Much love for the Va. 🌮 gatherings (and Md.'s eatsleeptacos!)

[@Delmarksman]

# MobtownOffroad !

[@ryanmurphy694]

Great video! Also have a 3 in lift and had to do this. Fixed it instantly! Found some one on Tacoma World in my area gave him $100 and did the exact same process.

[@johnbradley2016]

Ryan Murphy where are you?

[@ryanmurphy694]

John Bradley Massachusetts

[@yezkaholic]

Where was he located most guys want $300

[@ryanmurphy694]

In Massachusetts

[@yezkaholic]

@@ryanmurphy694 sorry I read your first response after the fact

[@adventuredrew512]

A few things: 1. My extractor tool nut size was 19 not 22mm 2. The tie rod puller, 35 mm socket, 250lb torque wrench can be rented from AutoZone (Advance Auto has wrench and tie rod kit but way more expensive as you have to rent a whole kit).

[@elurb7231]

You don't have like puller for the CV? With as often as the front has to come apart it's worth the 40-60€ investment. Also, prying on that part of the CV can bend the dust shield that interfaces with the oil seal.

[@joetousignant9130]

Come over Saturday with your tools. I'll provide the beer and BBQ. I have a 2006 Sequoia bone stock needs this 186,000 miles. My 2006 Tundra 156,000 miles is probably not far behind. I bought the ECGS sleeve and tool since I will probably being doing it again on the Tundra. My trucks are the same as your Tacomas but I have V8's LOL.

[@beardedyinzeradventures8893]

I have to do mine. It's bad with the new suspension setup

[@carbonking53]

I've got a 2020 4Runner ORP with a 3 ish inch lift with aftermarket UCA's with 17K miles on the truck. Did the lift about 12k miles ago and just last week started to get a strange oscillating/harmonic like hum and mild vibration most noticeable at 40-50 mph on smooth pavement. It comes and goes in a reoccurring cycle. No wheel shimmy or shake, but noticeable through the steering column, floorboard, and seat of my pants. I'm thinking this needle bearing issue may be the culprit. Time to do some deeper investigating and get this ECGS busing swap done if need be.

[@elhijinmartinez424]

My have a vibration between 60 and 70 over 70 vibrations goes away I think to remplace a the u joint to see if that is the problem

[@donthesheek]

If the differential has a spacer to accommodate the lift height is lifting still an potential problem for the needle bearing................?

[@rabs2020]

Just watched the video and very detail instructions also is this only recommend to do the driver side whatabout the driver side?

[@Tacomaholic]

Yes this is only needed on the driver side.

[@calmannomore5832]

Does this issue pertain to the 1st gen Tundra or does it use a different bearing?

[@warlok9]

Just bought a 2017 Tacoma Sport last month, factory certified pre owned. People kept commenting that my truck looked higher up, so I took a look and to my surprise the previous owner must have put a spacer/leveling kit on it, maybe 2” in the front and 1” rear. Anyways, I just recently started noticing this weird oscillating groaning vibration coming through the wheel and the floor. It’s subtle, so I’m sure it was there the whole time, just took me a while to notice it. After reading about needle bearings, etc. I tried putting it into 4H to see if it went away and it does. Will removing the lift kit spacers and returning the truck to stock fix the vibration? I’ve read some on the Tacoma forum where removing the lift corrected the issue. I don’t even want a lift on my truck, prefer it stock. I’m going to call the dealer where I purchased it today. They did not disclose that the truck was lifted (perhaps they didn’t know) because I probably wouldn’t have bought it had I known. Perhaps I can make a case for returning it. I’ve had it less than a month. I just don’t want to get in a drawn out song and dance with the service dept trying to diagnose and fix the issue. This is my work truck, I just need a truck that works.

[@Tacomaholic]

Removing the lift should help correct, if not outright eliminate, those vibes associated with the needle bearing.

[@tumbleweed728]

So this is the procedure for the driver's side only, as the passenger side is different?

[@dkshdw2004]

Would you recommend doing the needle bearing the same time as the lift? I'm thinking about 5100 all around, ome 888 coils up front, and an aal in the back, with a diff drop.

[@Tacomaholic]

Either then or when you are changing your front diff oil.

[@austinl5673]

Would this also be effective in fixing the common 4Runner Tacoma highway steering wheel vibration on stock vehicles? (Assuming all other causes have been eliminated like wheel balance).

[@Tacomaholic]

Hmm not sure about that one. Have you checked on the 4Runner forums?

[@WAEofFishing]

I'm getting ready to lift my truck. I'm doing the bushing ahead of time

[@Tacomaholic]

Good move! Even though the don't sometimes vibrate after lifting at first ... it will eventually be an issue.

[@kaydengilmore4840]

does the truck need aligned after this install?? Great video!! Im doing this next week and wasnt sure if ill need an alignment after.

[@Tacomaholic]

No alignment needed if you aren't adjusting anything on the UCAs or tie rod. The tie rod is disconnected during the install but that's all.

[@ryanrvaughn]

I aligned my truck the day after we shot this video, but that was due to the lift kit, not the bushing install.

[@kevinjackson65]

One more question. On my 2008 Toyota tacoma sport, my first lift kit was 3 inches in the front and 2 inches in the rear. Then I purchased an ARB winch bumper. Then I put blisten 5100 adjustable struts to 4 inch front and 3 inch in the rear. Now I've noticed that the front differential needs to be adjusted lower. The spacer that's in there now is for a 3 inch lift. Can you recommend a company that sells a front differential spacer kit for a 4 inch lift ? Thank for your time.

[@Tacomaholic]

All of the diff drops I've seen were for a standard 3" lift.

[@shawnphillips4473]

great vid now if it only took 20 min to do this it be great lol

[@agustinherrera5600]

What exactly do you feel or what should we look for to know we need to replace this in the tacoma ? I have a 2016 lifted about 3”

[@Tacomaholic]

I go over that at the 1:40 mark.

[@sakusan23]

What gear oil did you use to top off the truck? Do you remember if it was the OEM Toyota 75w85? My local autozone only carries 75W90.

[@Tacomaholic]

I just use the Valvoline 75w90 seen here: amzn.to/3iNVPE4

[@noahmeineke1415]

so trying to replicate the steel rope/hammer technique I pulled my cv axle into two pieces. maybe not such a great idea

[@jameshoward3071]

I have a 2019 TRD I don’t want anything real tall and I don’t want real big tires . What size tires do you use and what is the offset or back spacing of your wheels so that it doesn’t rub

[@Tacomaholic]

My tires are 285/75R16 which is a 33". My rims have 3.5" of backspacing and -25mm offset and they rubbed pretty bad.

[@zactastic4life]

Did he have a differential drop before or after doing the ECGS bushing? do you guys both recommend the Drop as well as his DIY?

[@Tacomaholic]

There's a lot of info about diff drops on Tacomaworld, but it seems they aren't really necessary and might do more harm than good.

[@ryu51890]

Put a 2inch lift on my Tacoma and immediately had the vibration. Just changed out the needle bearing, without pullin the axle from the hub, and replaced the bearing with ecgs. Vibrations gone!

[@terrysturtevant8800]

Just purchased a 2014 with no lift and only 43K miles. My hearing isn't what it used to be so not sure what I'm listening for. But I can move the Axles up and down. I'm thinking this should be done. As a second owner on a '14 would this still be covered under the original warranty? @tacomaholic tacomaholic

[@Tacomaholic]

I'm not sure if it's covered under warranty, but a quick way to see if you need the ECGS bushing is if you feel vibes in your truck to switch it into 4hi while going about 45 mph on a straight road, if the vibes instantly go away then you need the ECGS bushing.

[@ratoncolorado7227]

How big is that removal tool tend?, I have a few bearing pullers with the smallest one like that being 1''x 1-7/8'' just wondering if I could use the one I have rather than buying another.

[@Tacomaholic]

I don't know the exact dimensions but it's pretty small.

[@Tacoexplorer]

Thanks for the video. Wish some more details were mentioned regarding the new bearing install. How far does the new bearing have to go into the diff? How did he first align the bearing? Etc etc.

[@randallbrusher503]

To first align it, you just get it square with the hole, so it's nice and straight. Then once it's started you can break out the long pipe. As far as driving it in, there's a little metal ridge in there. You hit it flush with that. I recommend supplementing these instructions with the ECGS install instructions, for a complete picture with all the details and tips.

[@flmtbiker]

@@randallbrusher503 Thank you for showing us how to do this. I'm an old fart, shade tree mechanic who works in the drive-way like you. I have done many things to my vehicles but have been unsure about this procedure. Your clear demonstration of the bushing installation answered many questions I had. Thank you again!

[@kevinjackson65]

Hello. I would like to know where you purchased your TACOMAHOLIC emblems on your truck? Thank you for your time.

[@Tacomaholic]

Hey Kevin! Checkout the Tacomaholic decals here: tacomaholics.com/shop

[@kevinjackson65]

Hi. I checked the passenger side axel to differential and I was able to move it. Do you have the part number for the roller bearing?

[@Tacomaholic]

The ECGS clamshell bushing only goes on the driver side.

[@georgehernandez1826]

I have a 2016 Tacoma off road 4x4. I want to put a 2" lift on it. With your experience on having to swap out the bearings, do you think a 2" lift will require a bearing swap?

[@Tacomaholic]

Hard to say because it's not guaranteed that your truck with have vibrations after installing the lift.

[@georgehernandez1826]

@@Tacomaholic ok thanks for the reply.

[@justinlam7354]

How far in did you guys put the ECGS bushing in? I read it's suppose to be flush. But I'm having some issues to get it in all the way flush. It's sticking out maybe 1/16 of an inch (1/8" at the most). Any suggestions or advice? thanks

[@Tacomaholic]

This one was flush if I remember correctly. Have you made sure it's clean behind the bushing and anything small isn't obstructing it?

[@stevanrose7439]

Our 2012 Tacoma with less then 60k miles did a weird growling vibration a few months ago and I took it to a shop to have them find it and or fix it. And they couldn’t find anything wrong so I’m still driving it but I feel something sometimes and I’m thinking this may be what it is.

[@efil4kizum]

Couldn't find anything wrong ???

[@itunda5607]

Will the vibrations be constant at all speeds I just lifted my truck and I know for a fact my driveline angles are all messed up so I’m gonna order a woody, from off the line shudders to decel vibes will the needle bearing be at a specific speed?

[@Tacomaholic]

Needle bearing vibes are usually around 35-50 mph.

[@minibikesandmowers]

Is this problem avoided when you install a differential drop at the same time as your level kit

[@Tacomaholic]

I haven't heard of that ... but others have said the diff drop has its own issues.

[@dannyboi_3016]

Also how about a Tacoma 05 after getting lift , doing a slight vibration between 0-20mph ?

[@Tacomaholic]

Probably a driveline vibe if it wasn't there before the lift and either a carrier bearing spacer or rear axle shims might help.

[@stock7628]

I was going to lift my tacoma but after seeing this i know the cycle won't end here

[@Tacomaholic]

Lol it NEVER ends.

[@stock7628]

@@Tacomaholic This is a year later, I lifted my Tacoma and I will be doing this. LOL

[@Z-Ack]

1200 miles on it? What is it registered or a trailer only fun wheeler? Ive never owned amything with less than 60k.. couldnt imagine doing that much to a truck while it still had the new car smell in it...

[@goodtimesrkillinme1]

So i just got my 2020 Tacoma OR... I want to lift it but i was worried about issues brought by lifting. Other than this bushing, are there any other issues that may arise? Also, the edits in this video are hilarious.

[@Tacomaholic]

Trimming issues with fitting larger tires plus other vibrations with the driveshaft being off compared to the stock geometry.

[@pablozagala8670]

Is this only a Tacoma Issue? I recently purchase a 16 Tundra SR5 and just lifted got new tired and alignment done but truck keeps vibrating around 60-65 along with my steering wheel.

[@Tacomaholic]

I'm not sure if the Tundra's use the same/similar setup.

[@user-ni6vd2ly8y]

So Iam about to order the bushing for my truck. I seen that there is play on both side. I was just wondering if you know if the bushing work for both sides or just the driver side ?

[@Tacomaholic]

Driver side only. The passenger side has a different setup.

[@user-ni6vd2ly8y]

@@Tacomaholic Thank you do you know if it a ball bearing on that side by chance?

[@Tacomaholic]

@@user-ni6vd2ly8y I'm not sure what the passenger side setup is, but I've never heard of it needing to be replaced.

[@user-ni6vd2ly8y]

Thank you! I appreciate you taking time to help me out with this.

[@Tacomaholic]

@@user-ni6vd2ly8y Any time 👍

[@at1970]

I have a 2009 TRD access cab with an AT summit wedge camper on it. Suspension is stock. The camper has squished an inch or 2 of the lift. If I lift the truck just back to ~ normal do I still need to mess with the needle bearing? Thanks

[@Tacomaholic]

I would guess that if you are lifting it back to the stock height you wouldn't have issues with the needle bearing ... but if it's off by just a little bit the issues could develop.

[@at1970]

@@Tacomaholic Makes sense. Any idea if it’s the opposite as in the truck is sagging from a load? Is changing the angle bad if it’s lower not raised? Thanks

[@at1970]

@@Tacomaholic Also. Do you know of any difference between the bushing from east coast gear and the one from nitro? I can get the nitro one locally. Thanks

[@Tacomaholic]

@@at1970 I'm sure the part is the same between the two companies.

[@papabear007]

I have a 2020 Tacoma TRD off rd with 2000 miles just had a 3/2 spacer lift done new rims tires 285/70/17 front end alignment. Between 50 and 60 I get little shake in starting wheel not bad but strange. The shop said drive it for two weeks bring it back and if still an issue they would rebalance the tires. Any suggestions

[@Tacomaholic]

Pop it into 4hi next time it shakes like that if you are on a straight road and going less than 65mph. If the shake instantly goes away then you need to replace the needle bearing with the ECGS clamshell one as seen in this vid.

[@TheMffd26]

Did you get it fixed

[@6ix13ree]

Mine has an on-off vibration only between 60-70km/h (38-43mph) is this the fix? Also lifted with a spacer..

[@Tacomaholic]

The vibe goes away when you put it into 4hi?

[@RCPropaganda]

Ughh i needed one after like two weeks of being lifted.

[@yezkaholic]

Wow so quickly? I'm thinking twice about lifting now lol

[@RCPropaganda]

@@yezkaholic lift is great. Just find someone that can do the the needle bearing.

[@yezkaholic]

@@RCPropaganda I read somewhere that the 2018 and up have "upgraded" bearing but looking at forums it's BS. How much did you pay for yours I'm in California most shops want $300+

[@RCPropaganda]

@@yezkaholic i got lucky met a guy on local fourms he did it for beer. Just bought bearing puller tool then sold it after.

[@yezkaholic]

@@RCPropaganda that's dope, so after you replaced the vibrations went away and never came Back? Yours is a 3rd gen right?

[@Cutiefly91]

So how long can i go before changing this out? The vibration isn't to annoying yet and I can deal with it. Its not harming anything is it?

[@Tacomaholic]

Better sooner than later since wearing that bearing out can lead to bigger problems.

[@mmunoz5875]

When getting this done, is a alignment required afterwards?

[@Tacomaholic]

No alignment needed.

[@jamesstepsidechevy]

Is there a passenger side bushing as well. Or do you only need to do the drivers side?

[@Tacomaholic]

No the passenger side is different. Only driver side needed.

[@jamesstepsidechevy]

@@Tacomaholic so does the passenger side not have a needle bearing?

[@Vikingguy187]

I have a 2015 2wd, would this be useful to replace for me? I have had shaking in the steering wheel even after balancing the tires since I lifted it. Running a spindle lift in the front and emu springs in the rear

[@Tacomaholic]

Are your vibrations around 40-50mph?

[@Vikingguy187]

@@Tacomaholic exactly at 50mph

[@Tacomaholic]

@@Vikingguy187 Yeah it would be worth trying then assuming your tires are balanced.

[@kevinjackson65]

So if I replace the needle bearing on my 2008 Toyota tacoma with the clamshell bushing, should I go ahead and replace the ball-bearing on the passenger side?

[@Tacomaholic]

Passenger side never seems to be an issue.

[@kevinjackson65]

Thanks for getting back to me so fast. Every video I've seen so far has really helped me out with my truck.

[@Tacomaholic]

@@kevinjackson65 Thanks so much for watching Kevin!

[@Ryan-vw8sq]

Cool vid, but what's a vibe? vibration?

[@Tacomaholic]

Yep, vibration.

[@davidreberger9318]

My vibes on the passenger side so do I replace both ?

[@Tacomaholic]

This is only for the driver side. Passenger side is setup differently. But usually vibes felt from this issue are sort of generalized and not side specific.

[@grizzlys91ify]

So I lifted mine 3 1/2 Inc. Full suspension lift and I didn't have the vibe at first it was a few days till I started feeling it. So there are 2 of these needle Bearings one on each side correct

[@Tacomaholic]

No just 1 needed for the driver side.

[@grizzlys91ify]

@@Tacomaholic witch way to I put it in. Flush side out or

[@Tacomaholic]

@@grizzlys91ify The ECGS bushing is the uniform if I remember correctly, so you can't put it in the wrong way.

[@grizzlys91ify]

@@Tacomaholic no there 2 different sides ones flush other side is not. But I looked it up and flush side has to be out. When I was takeing the Needle bearing out the tool dug in to the I side as bearing was comeing out so hope to God it will be ok. I have bye bushing in freezer for the night. So I can put it in. When I get up in morning

[@Tacomaholic]

@@grizzlys91ify Let me know how it goes.

[@jameshoward3071]

How did he get the shock off without taking loose the upper control arm

[@Tacomaholic]

That was done earlier since this truck was getting new UCAs at the same time.

[@lespaulguitarist92]

but its not require to remove the shock to get the axle out. unless it a beefier shock i guess.

[@defstar1774]

So with a OME 2" lift this needle bearing needs to be replaced?...does Toyota use the type bearing on purpose to discourage lifting?

[@Tacomaholic]

Did you get any new vibrations after the lift?

[@defstar1774]

@@Tacomaholic Haven't lifted yet...want the two inch lift but not if I have to replace this bearing.

[@Tacomaholic]

@@defstar1774 One of those things you just won't know until you do it.

[@louieserrano8952]

I have the Old man emu 2" lift and yes mine vibrated, went away in 4h like he said.

[@northerntoyota7584]

I need to do this on my 2005 after ome lift. I 100% Expect my axel to be seized to the hub. Here’s hoping it’s not 🍺

[@JuanManuel-fm9jt]

IS THIS ONLY DONE ON DRIVER SIDE?

[@Tacomaholic]

Yes

[@jyj3843]

You say "if you put it in 4wd and you still have the vibe, then it's PROBABLY something else". Is it POSSIBLE that the source of the vibration and hum could still be this bushing even if the vibration and hum doesn't stop when in 4wd? I've already replaced the front hub/wheel bearings. Anyone's input welcome, thanks.

[@jyj3843]

New shocks/struts, tires and wheel alignment as well so it's not tire cupping either but that's kinda what it sounds like ofcourse.

[@jyj3843]

I'm asking is the vibration going away when put into 4wd a *necessary* prerequisite to being able to determine the problem is the needle bearing or is it possible the vibe can still be the needle bearing, I heard u saying probably or kinda.. I'm just trying to determine definitively if I can. 2007 sequoia limited 4wd

[@Tacomaholic]

From what I've heard if the vibe goes away when you put it into 4hi then the needle bearing is the issue. Does it feel like you have any vibrations coming from the middle or rear of the truck?

[@jyj3843]

@@Tacomaholic No it doesn't, it really all feels and sounds like it's up front. I've heard however about how people have sworn the noise was coming from up front but it was the wheel hub/bearings in the rear (the sound traveled). I'm going to check the rear by spinning for bearing sound and checking the tires for play when lifted. But yeah I'm a little stumped then. I was really hoping that needle bearing could act up in a variety of ways including mine (vibes at all times after about 20mph) so that the clamshell would be the fix.

[@Tacomaholic]

@@jyj3843 It's frustrating hunting down the vibrations sometimes. A rear axle shim and carrier bearing spacer could help too.

[@HonRon211]

Stupid Question Alert....Do you have to do the passenger side bushing as well? Or is the problem only with the needle as the passenger side is a tube bearing?

[@Tacomaholic]

I'm not even sure if the passenger side is setup the same way as I've never seen anything done with that side.

[@HonRon211]

@@Tacomaholic It isn't it has a ball bearing...which according to ECGS's FAQ page "normally does not go bad." So shame on me for not reading first. Thank you for the quick reply!

[@technician799]

Is this an issue when just installing a leveling kit up front?

[@Tacomaholic]

Depends on how much lift

[@technician799]

@@Tacomaholic 2 inches up front makes it level, so just 2” up front. I don’t mind replacing it but want to order everything at once if I need to replace it.

[@Tacomaholic]

@@technician799 It's hard to say. Some Tacomas need it and some don't ... but it's a good idea to go ahead and do it.

[@agustinherrera5600]

How do you choose the correct one . The one on your link says 8” and on their website they have a 7” ,8” and 9”

[@Tacomaholic]

The 8" one is for 05-current Tacomas. I'm not sure what the 7 or 9" ones are for.

[@agustinherrera5600]

@@Tacomaholic thank you

[@noahmeineke1415]

you guys didn't mention separating the lca? did I miss it?

[@Tacomaholic]

If I remember correctly the LCAs were able to just be pushed down without loosening anything. This was on a newer truck though.

[@noahmeineke1415]

@@Tacomaholic the lca needs to have two bolts removed to sway over like you indicate

[@fogduker3131]

Is the bushing just on the one side the drivers side

[@Tacomaholic]

I'm not sure if the other side has a similar bushing, but even if it does the driver side is the only one where there is an issue.

[@fogduker3131]

@@Tacomaholic thanks for the information

[@Tacomaholic]

@@fogduker3131 Any time. 👍

[@webcrawler3332]

So you’re removing a bearing and putting a bushing in its place? I thought bushing don’t last that long compared to bearings?

[@Tacomaholic]

Not sure in other scenarios but in this case the factory needle bearing is far weaker than the clamshell bushing. I've never heard of one of the ECGS bushings failing after install.

[@davidchandler2276]

How can I remove the needle bearing outer housing if the puller destroyed it? All that is left is the outside shell.

[@Tacomaholic]

If small pieces of the needle bearing remain inside then you need one of these telescoping magnets to help fish all of the pieces out: amzn.to/3a8Y0A4

[@davidchandler2276]

@@Tacomaholic yeah I did that but the outside of the bearing is still stuck inside the hole. Any ideas on how to get that out?

[@Tacomaholic]

@@davidchandler2276 I've never heard of that happening before. Did it just snap while you were trying to pull it out?

[@davidchandler2276]

@@Tacomaholic yes. I can send a pic to you if you want.

[@davidchandler2276]

Got it!!! Cold chisel and a hammer! Thanks for responding earlier. Pretty cool I got to message with you. Love your videos! They have helped me tremendously!