Ceiling Cassette Cleaning Hacks You Need to Know

How to clean mini splits?
• Mini Split Cleaning Ha...
How do I get to the ceiling cassette drain pump?
• Ceiling Cassette Drain...
Ceiling cassette mini split tips
• Ceiling Cassette Mini ...
Ceiling cassette drain pump maintenance Video
• Error Code E153 Samsun...
Nu-Calgon 4150-03 Clean Guard CC
amzn.to/44D7flJ
Coil Gun
www.nucalgon.c...
Click here to buy
amzn.to/3OHAKyl
Complete Care Mini-Split Kit
www.nucalgon.c...
Click here to buy
amzn.to/3DzmvF6
Turbo Tank 2.0
www.nucalgon.c...
Learn more about Nu-Calgon Products
www.nucalgon.com/
Wanna Learn more about hvac? Check out my hvac tips for technicians playlist.
• HVAC Tips for Technicians
Join this channel to get access to perks:
/ @taddydigest
Taddy Digest Website
taddydigest.com/
Click this link to get your website consultation.
moderncontract...
Modern Web Studios has Built, hosted and maintained my Website.
modernwebstudi...
Fill out the contact form at modern web studios
modernwebstudi...
‪@nucalgonmicrotrainings4647‬

[@BeechWalter]

Very useful video for novices. My wife and I followed Taddy's sequence as we took apart a Bryant cassette similar to the cassette Taddy works on. We brushed off most of the grit that clung onto the grill. We cleaned the coils with A/C Foaming Cleaner spray (ACE Hardware). Let the foam stay on for 15 minutes. Then rinsed off the foam with water in a spray bottle and removed the drain plug to release dirty water into a pail. We reversed Taddy's video to reassemble the cassette. Two useful tips: 1) Before disconnecting wires, take a several photos of the circuit board and place tape on wires to identify which plug goes into which receiver. We marked one set by writing "1" on 2 pieces of tape. Attach the tapes to the plug and receiver. To reassemble, we pushed plug 1 into receiver 1. 2) Use KZbin videos like "You can't remove this connector" to learn how to disconnect and reconnect wires to Molex receivers that are on the control circuit board.

[@TaddyDigest]

very cool Thank you for sharing this and for watching

[@davepeera1247]

Just one more point...I think the Idea of the video is to encourage a homeowner to do a simple job by himself. But as you finish the cleaning process the remaining sockets in the unit will be with moisture or water which has a good chance of short circuit if just plugged in . Suggest you need to blow dry whatever connectors after the cleaning process

[@عبدالرحمنالعرفج-ط1خ]

Thanks for providing a simple way to get the job done.

[@TaddyDigest]

Glad to help

[@AaronPowellvox]

Good stuff. I liked seeing how that comes apart. If I run across them in the future I’ll know how to tackle it.

[@TaddyDigest]

Awesome bro thank you for watching

[@stephenyoung1221]

Steve from Boston. Great explanation

[@davepeera1247]

Taddy .. thanks for the video. Need clear a point. As you wash the coil the dirt fills in the drain pan and overflows to the maintenance bag. As so isn't there a chance for dirt to be stagnated in the pan and choke your drain pump or line ?. Suggest it would be better to have the drain plug removed in the cleaning process ,so that all dirt would drain to the bucket.

[@Steve-fp9yw]

I was wondering the same

[@TaddyDigest]

That is correct

[@Mayneverknow]

Thanks for making this video. One consideration. Since we always want to clean coils opposite direction of air flow - maybe it’d be best to completely drop the drain pan - add your coil cleaner to the inside but wash the coil from the other side. Probably get a 90 adapter for the pressure washer - make sure it’s not any kind of pressure that can damage the fins. Just an observation - probably over thinking

[@USA-GreedyMenOfNoIntegrity]

Taddy, I’m glad I don’t sell those things unless a standard split hp is not appropriate for the situation. American Standard AH PM: Turn off circuit breaker, remove Twelve 5/16” hex screws, remove air handler panels, clean coil, drop algaecide tablets in pan, inspect electrical, reinstall covers, screws, turn circuit breaker on. Done in 6 minutes. It takes 15 minutes to get prepared and just get access to those mini split coils and then hope n pray you don’t break any of that plastic or those connectors. Then hope it doesn’t throw an error code once you wrangle it all back together.

[@vittayoem2]

Thanks for sharing

[@mightyhellscream5014]

Can i clean it without removing the electrical part? Just covering it

[@johncraig446]

Is this the same process for a Mitsubishi Sillen cassette?

[@TaddyDigest]

Yes

[@mjyumping]

Hello, I'm trying to take the fan blower off my indoor cassette unit. I've removed the nut and the special washer but the fan blade won't come out from the shaft. Anything else that could be the culprit?

[@TaddyDigest]

sometimes you have to wiggle the blade give it a good tug

[@bp0100]

where do you get the quick coupler adapter piece to connect the coil gun?

[@TaddyDigest]

comes with the turbo tank I think

[@bp0100]

Yes it does it actually just bought it yesterday thanks!

[@simpson156]

Can a single cassette heat and cooling a 800sq.ft 3br home?

[@TaddyDigest]

It depends on the layout and also depends on if it's foam insulated. I put a three ton mini split cassette in a foam insulated three thousand square foot house Ten years ago and it's still works great

[@simpson156]

@@TaddyDigest Alright it's a all brick home 10in thick 2 family home. Flat roof rectangle layout. No foam insulation and I want to only put it in the second floor. Is it do able and what size do you recommend.

[@johncraig446]

Ceiling

[@jonathanbasiliere1327]

Taddy a bad mf

[@TaddyDigest]

Tadley wadley bo badly oh yeah 😎 😏