Tail Rotor Transmission Shaft EXPERIMENTAL HELICOPTER BUILD SERIES (Part 46)

[@rockyrivermushrooms529]

My favorite series on youtube👍. Is the helicopter designed to go into auto rotation if the engine fails?

[@ultralighthelicopter]

Thank you 🙂 Yes the helicopter has a freewheel unit to allow the rotor keep spinning in case of a engine failure... (part 43 of the series)

[@ahmdabdallah5811]

@@ultralighthelicopter  God has said in the Quran: { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) Quran

[@NEV4G]

As an ex CH47 technician I know how this works but I still love seeing it. Great animation. Please do the CH47 flying control run next. 😂🤯

[@감광식]

아주멋잇슴니다

[@drush525]

Super cool. Might I suggest you continue drilling out those holes throughout the entire tail rotor mast reducing weight even further. Then press flute the clearanced portions longitudinal for added rigidity.

[@mrboby5]

Hola, buen video ya queda menos, gracias por compartir.

[@kanartech]

Can't wait to see this due process flying

[@TuberEver]

I am very impressed and very Curiosity to see the next part, I think that is the tail rotor✌✌🚁

[@madeofsteel.9618]

Super trabajo. Felicidades. Desde el inicio lo estoy siguiendo. Me encantaría verlo en el aire . Felicidades y aquí con usted amigo , hasta el fin . Sa.udos desde México

[@nguyenlinh.maybay]

làm tốt lắm .👍♥🇻🇳

[@bruceyoung1343]

You got a lot done in this video. Congratulations. Getting closer to run up That will be a exciting time both there AND here. Lol

[@danielc9312]

My only regret is that I have but one like to give.

[@kicmospas155]

Mnogo rada i truda,jedva cekam kraj proizvodnje i pocetak leta!

[@maurosergiopossas9694]

Very good

[@truckerray7533]

Job well done as always, but ive got a question for ya. How come you didn't install tail rotor shaft bearings on your internal shaft plates. . . .wouldnt that have been a better over all choice???

[@ajammolla9241]

How much does it cost to make one?

[@jcmaosaobra2791]

Muito muito bom parabéns pelo Zelo!

[@empty8866]

Good Job

[@muhammadkhodadadian7336]

Hey, I think it was better to use some bering fo the resting place of the tailrod!!

[@espacovidanovakids8359]

Parabéns pela genialidade, sem comentários

[@pikodkc]

Nice job, but why you didnt use bearings to suppot the transmision rod across the big pipe instead bushings?

[@kukuhwidodowidodo1440]

mantap booos mksh

[@brianhaselden9186]

Be curious as to whose blades you plan to use. Me, I'd go with composites. Still, keep it up!

[@muhammadridwansyah9665]

Mantap

[@miftanyanyun2650]

Nice

[@AviAero123]

Hi, why did you plan to have rubber bushings with just lubricant brushed upon, in internal brackets instead of ball bearings?

[@mardindhyn957]

👍👍👍

[@sarcamahardika]

See from indonesian

[@jcmaosaobra2791]

very good the whim but this type of milled union in my opinion wears out very fast the ideal would be a union with a damper but congratulations your service is great

[@norbertadrian7468]

Bedenke die Material Beanspruchung. Ein helikopter muss flexibel aufgebaut sein.es entstehen sonst starke Schwingungen. Habe viel gebaut und getestet

[@rklaskar6157]

When it's gonna be complete?

[@jamesmogle2888]

Great job with your videos! Are there plans available for this helicopter?

[@Leo-cu1yq]

I need a friend like you

[@معاذعميس-ض9غ]

هل تستخدم كتب في الصناعة وما هي ؟

[@norbertadrian7468]

Hallo helifreak .bitte beachte die Dynamik beim Betrieb. Ohne flexkupplung gibt s früher oder später rissbildung.bitte die Welle kugellagern.die Sicherheit steht an 1 stelle .

[@powerbumiarto4964]

Good..ok..

[@Esoteric.Knowledge.Evolution]

Hii brother love & respect from India.. U r a amazing engineer, craftsman, fabricator, designer.... U should open a channel where u can teach online how they can built this ultralight to the masses with fees of course

[@haragrapegarden8061]

Saya tidak sabar menunggu uji terbang

[@edwardarruda7215]

Please provide the total hours to build and cost of materials.

[@Mr.shah081]

How much the cost of entire parts including engine?

[@billyjasinski1265]

I don't know if this is what you are looking for, but I think you should stick to the intro format from the first 30 videos. changing it up is cool, but I think it is still important because it is sorta like a PowerPoint. eventually, somebody will binge it and think it looks weird.

[@pikodkc]

hi, how is going? we miss ur videos

[@babuprodan1392]

Hiii

[@ankit-tv7fg]

Prize kitna h

[@nazai-tech4362]

Hello sir, I want you to train me

[@nazai-tech4362]

answer me please

[@ramchandrabhartiya5787]

Hindi mebtao

[@babuprodan1392]

Hiiii