HOW TO RESET CHECK ENGINE LIGHT CODES, 4 FREE EASY WAYS !!!

[@TampaTec]

under $20 car scanner (works with gasoline cars 1996 and newer) it scans for errors and resets code but you need to fix the issue otherwise error code will trigger again. OBD2 handheld Scanner amzn.to/2kEjN6E OBD2 bluetooth Scanner-amzn.to/3n34xDP * affiliate links

[@badseedzontop5687]

when I start the car its not showing but I had the key in the ignition and it was showing. did I do it right?

[@badseedzontop5687]

the igition switch has 1,2,3,4 correct? when its on 3 the light is showing but when I start it its off. my gas cap is good

[@jchurchill75]

Doesn't work if you need an inspection sticker. I know for a fact.

[@krislizana2017]

BadseedzOnTop vehicles are designed to show lights before starting so you, the mechanicand (or) the state inspector that the bulb is working and or not removed/bad. it goes away after starting the engine assuming there are no problems related to emissions, or severe engine damage. if the light shows up before you start the engine, you know the bulb and circuit is good. if it goes away then you have no confirmed codes stored in the computer. you may have a pending code or two. but will not cause the light to illuminate until confirmed

[@mkmanir]

Tampatec I

[@kendrawilliams3422]

Thank you for the tips. I have been working on my own vehicle now for a year. I did exactly what you showed in the video. I fixed my truck and rode around for some 75 miles and the check engine light would not go off. I disconnected my battery for 1 minute connected it back and the light went off. Thank you, thank you, thank you!!!!! Your the best!!!!!

[@triumphmanful]

Went to my mechanic for Inspection after reading code. Reset it like you did with the negative wire to pos. Worked beautifully ! No problems. Inspection went smooth. Thanks so much. You are #1 !

[@pixiejudy10]

I'm so grateful for this video. Haven't tried it yet, but I've had this problem for 3 years, getting a vague code (440 I think) that mechanics can't pinpoint but charged me a fortune trying different fixes. I was on the point of buying a new car I couldn't afford because this one failed inspection and I didn't think the mechanic (different from the inspection shop)who reset it would do it again. If the battery trick doesn't work, will get the diagnostic tool as I saw the mechanic use it to reset codes. I'm so grateful for this info.

[@MrUniversalone]

Thanks for the great video, ive normally paid £30 a time for auto electrical engineer to come out & sort the light out x3, i never realized how simple it was but then again, the electrical engineer would not be about to tell you that, they just want your money even though he was done & gone within 5 minutes. Mechanic also checked & told me its only indicating a minor issue & no big deal, hence another £35, so i am going to give this a go the next time as it come on which is only now & again... 3 times a year. Greatly appreciated!!!

[@noreenebostick9593]

Thanks so very much for sharing this video. I am 65 years, five months and 22 days. I enjoy learning how to learn about vehicles. It allows me to put focus on whatever I own and operate. Smiles

[@UwereBamboozled]

Thanx for the vid. I tried it and...TADA, it worked. Pretty sure it came on due to a bad muffler that was replaced not too long ago. Tech didn't reset it after replacing it. You saved me from having to go back to a mechanic to get it cleared.

[@raptureangel5409]

Here, mechanics (dealerships/shop owners) will vandalize your car, never saw that before! So, have a private mechanic working on my car, the videos really help!

[@akmt123]

Did it again today, all o.k. now...been twice to Ford, first time ripped me $150/- for Diagnostic Testing...today again wanted $150/- for the same Fuel Tank Purge Valve recall...nothing has been changed since 2011 on my Gas/Petrol Tank respect to the Recall!!!!

[@ashleye559]

Thank you Tampatec 👏 I've had two different dealership's try and hit me with that diagnostics crap after I told them my battery had faulted. Replaced my battery and all light's are off and Radio is no longer Locked!! Your a freakin life saver 🤗

[@brucehickerson5967]

Mine went out after taking off my battery terminal and by waiting five minutes. I appreciate the information. The last time the engine light came on it went off after using premium gas from; Shell, Chevron and Exxon and by driving around a day.

[@AbdulRehman-ri1xr]

Very nice.. Thanks mate.. It's working.. After waiting for 5 minutes while negative terminal was removed.. It worked

[@daviddarmody937]

Thanks a million for this video. I have a 2008 smart car and the repair manual cant be found in any parts house..however for the cost of an air flow sensor that is easy to find I may just take a chance and replace it..great job on this video...

[@richardbenavides7238]

This is a very good video. Easy to understand for an Office worker. Didn't know how to start at first. Thank you

[@aniezaliezas6451]

Tks

[@robertpeeters8868]

Very clear and concise tutorial. Great Video and Audio. Very often, the speaker is not clear. Thanks

[@B83RZ]

outstanding! the check engine light on my wife's ford escape lit up on her. before bringing it to the dealer i thought of doing the disconnect procedure & got it off. btw its a company car so its well maintained. thanks papi!

[@nopwoc]

Thanks for the info. My wife had refuelled on a trip to town and the check light came on. I watched your video and sure enough the petrol cap (UK) was not secure and loose! re-secured and reset light by battery disconnect. All good, cheers!

[@TampaTec]

nopwoc cool, it's common for that to happen.

[@emmy0076]

Thanks Tampatec. i bought the scanner on ebay and it solved my problems on Hyundai Santa fe. easy to use.

[@daveb3357]

Thank you very much. Disconnecting the battery worked like a charm.

[@عابرسبيل-ت1ظ]

thank you, resecuring the fuel cap and hard booting the power, fixed it

[@stroys7061]

Excellent video - no extraneous BS!

[@hayleyboley6754]

Hey , so my check engine light popped on yesterday, went to auto zone and the codes said I needed this part and I bought it went n got it fixed , from someone who isn’t like a real shop he knows how to work on cars tho , he fixed the problem the codes were saying, he did that one thing to make the check engine light go away but when I was driving to get money it popped back on!!

[@ahmodahmed1453]

Thanks and very clearly on your explained on trouble shooting.

[@2150dalek]

My 2013 Jeep Wrangler had the GASCAP error light come on...After cleaning O-ring, and tank lip as you said. The GASCAP error went away but only after driving home from work next day......and a day later the O2 sensor quit staying on....Was worried there a bit but cooler heads persevere I guess...Thanx dood.

[@DjJtown]

Not too bad of a vid but I suggest you upgrade your tools as in the comment I left below. I've been working on vehicle for 20+ years and to say things have become more complex is an understatement. I have an example, and it is my own nightmare. I lent out my MD75 to a friend a while back who went out of town for a month and had an issue with my car. Using my neighbors scanner, similar to yours, I retrieved the codes. It went from one to another to another. All in all I spent over $800 just to find out it is a weak fuel pump which will cost ANOTHER $185. I replaced the MAP sensor ($45) , Knock sensor ($65), Crank sensor ($60) , IAC solenoid ($68), MAF sensor ($139), Cam sensor ($129), Catalytic convertor assy ($280) plugs and wires ($70) along with getting the injectors cleaned and flow checked ($80). If I had the MD75, it would have shown the issue right away thru a poor injector pulse pattern due to low/intermittent pressure.

[@drumskas]

Gave me a pretty good idea of whats going on in my car. I have nissan maxima 03 with the following codes, P1614 & P1456, the last code is basically the same issue you showed in your video, its got to do with the EVAP leak, fuel cap, etc. and the first one has to do with some problem reading the signal of my key, Now let me just give you a reference, I have a key installed under the steering wheel ( for remote starter purposes )

[@CharlieAtkins]

+drumskas... P1614=is an Immobilizer chip key code... Key on or engine cranking, system voltage over 10.5v, and the PCM detected a problem in the Nissan Antitheft System (NATS). P1456= is an EVAP system leak (Very Small Leak) .020" leak

[@jenniferwilson5064]

Wow cool dude I can work on my 68 Camaro RS/SS with no problem but these vids you make make this new crap so much easier with no hugely expensive computers to buy. tahnks

[@degenninja1628]

Thanks bro great help just saved myself $550 for doing a 15 min job! Cheers

[@sheilabrewer4254]

C

[@albertlopez7146]

Cool video, thanks bro! Gonna get a scanner so can do it myself for future problems, won't have to rely on anyone else. God Bless...:)

[@simonmoiphemedi7242]

Nice one!!is working,it goes away afte starting the car

[@elonasingroy7500]

Thank you so much . My check engine light came on after I had some work done on the 1999 S 70 Volvo Gas door that was not opening. The Mechanic shop could get the part to make it work electronically so he tide a zipper in the truck to open the gas tank so I can open the gas door to get Gas to fill up . The Mechanic shop said the tester code did not say any thing wrong, but the light is still on and it is safe to drive . Your video explain what to do and how to read the code and look for the issue. I will check with Auto zone tomorrow. I Thank so much

[@frankyip6443]

This was great to know. Can save time than going to a mechanic who will charge a fee. Thanks and keep up the good work.

[@joshuabader]

nice the jumper cables from the neg to the positive reset the check engine light..still gotta drive it for 30 minutes..see if it comes back and do the obd2 scan again

[@juliefauson9639]

Good job showing the steps!

[@igorcabrera8123]

Man I`m following your steps, I was following you on TV repairs and now the same in electronic cars issues

[@juanfigueroa1246]

It's always good to watch thank you much

[@username8171]

Well I'll be, it worked ! Have yet to drive any distance but got my hopes up .

[@JVBO55]

thanks a bunch! I unplugged the negative cable for 10 mins n did the trick on my Celica. I hoping the sensors are just too sensitive or it'll be back in a few miles. but thanks 😀

[@TampaTec]

just in case it's best to carry car scanner $18. link is in video description, that saved my ass few times, saved me $$ getting ripped off too.

[@hubertcumberdale4978]

+Tampatec since '07 its universal, obd. 'vag' uses diff protocoling (vw/audi etc.). unplug battery, both poles and try connecting +/- wiring, hold-down for a min orso, make sure battery is in-total disconnected .....!!!

[@tinasheserengwa4230]

I own a Nissan Xtrail and need a scanner devise how can l get it. Am in Zimbabwe

[@jesuspizarro3921]

Cleared my code by removing the negative! Thanks

[@notachance213]

Simple and to the point, ,,,,,,,thanks great vid

[@AlbertoGarcia-mo9vw]

Just tried this. It worked. Thanks.

[@jasonpeters9295]

You explained it nice and clear. Thanks

[@randolphcoardes5680]

Jason Peters

[@MultiWayland]

thank you i will go to auto zone today to do this because my check engine light came on today 2005 Camry once again thank you > wish me luck !

[@DSmith-ix1xf]

Really good demo! Thanks 👏

[@eldenmayes7903]

Thanks for the it was big help please keep the videos coming thay help me alot thanks alot

[@Klim3834]

Thanks buddy! you are such a terrific guy!

[@thomasreed181]

Thanks! Really helped!

[@josel.arambula534]

Very helpful video it worked for me at all Thanks so much dude!

[@billsalus2750]

That battery cable method worked on my 2011 Ford Flex. It removed the search engine light. I only had battery cables as connectors instead of the small jumper in the video.

[@zion2913]

it was brilliant thank you so much i wish more mechanic was like you bro always watch your youtube videos from now on keep up the good work and telling use no heads how its done and keeping us informed when we are stuck, thanks bro your the best i am your fan. i will be watching your videos. nice one.

[@qzorn4440]

wonderful information... thanks a lot....:)

[@billchessell8213]

The most important part of this video is the ring on this gentleman's hand. When he gets the ring between the positive connection on the battery, or ANY positive connection AND any other part of the grounded car (negative connection), here's what's going to happen in slow motion. The ring will conduct unfused current at as many amps as the battery can produce, through the ring. The ring will be arc welded to the connecting point(s) and INSTANTLY become red hot. A brilliant flash of light will startle the shade tree mechanic and he will jerk his hand away before there is even time for the situation to register in his brain. He will leave the ring and his ring finger cooking in the engine compartment. Don't wear a ring when working in the engine compartment of a car. Any other mistakes in this video are forgiveable.

[@michaelcullitan5999]

good information thanks

[@heyitsrick01]

UPDATE AS OF FEB 2018, Autozone does NOT reset the code... They'll tell you the code meaning, but the service engine light/check engine light will still be on

[@justinjoe9610]

NExt time - please omit the noisy "music" so we can hear you more clearly ! Thanks and keep up great work We appreciate you !

[@jovengrino2286]

Thank you for sharing

[@shirleyvllj]

Hi Tampatec - Is the diagnosis test code reader reads 2012 VW manual beetle? Thanks for your good work.

[@chesseandonionpasty]

Thanks, very helpful.

[@franzlimonta1171]

Thank you so much for the thorough explanation!

[@rustyir1666]

Hi there, I have a dodge stratus 2006 model just wanted to know if there are different devices for dodge cars or if all these devices are standard for any car?

[@emyhuerto5764]

Thanks for sharing . . very helpful ! ! !

[@mederickamedo1289]

Many thanks bro. I learned from you. god bless you!

[@PunjabiFoodAndTravel]

Good job

[@onyeamastephen4466]

I love this

[@biologistjim4905]

Thanks for great info

[@fanzhang6936]

thanks ! You help me a lot!

[@erictripp9428]

Thanks for the video. It helped :)

[@puiu]

Worked on Toyota Rav 4 III . Disconect baterry. Thanks !

[@dawnanghsengaung1083]

Thanks You Sar

[@warhawk2219]

From the bottom of my car's engine, thank you so much gear head brother. If you need a kidney, hit me up. ..

[@SentinelEx]

Video liked. Greatly appreciated.

[@Ajridertat24]

ty the tip you gave me worked

[@dthomas241]

helped immensely.

[@ericg8822]

yea, it worked for my 2008 honda civic. What i did is put the key in the ignition, turn the car in position to crank, popped the hood, disconnected the neg terminal for 5 min, then reconnected it. Cranked the car and the light went toff but before hand one switch for oil pressure senor P0523 was loose, then reconnect and all done thank you @tampaTec so much saved me some cash!!!

[@oldman8810]

How do you figure that's a Cold Air Intake? The stock air cleaner drew air from the outside of the engine compartment. The way I see these things set up is they draw Warm/HOT air from Within the engine compartment. One might get better performance from a more efficient filter just like we used to flip the air cleaner cover on our carbureted Chevys but we sure as hell wouldn't have called it a Cold Air Intake :/

[@jerwin850]

Nice and good

[@humblelifeoutdoors4299]

Great tips, can’t thank you enough bro ✊🏽

[@mikailokewole5549]

Tampetec, well done. Please I want to get training for Brain Box Diagnosis and repair

[@markcomputer2968]

I have vw passat 3.6 2006. I just have a question. Connecting the negative to the positive won't do any do any harm for engine or the car? Thanks

[@rodneymason7214]

thanks for t he info, and also do you know anything how to fix jvc 50 inch tv having trouble turning on, thank you

[@MartyChristianSoldier]

You did a good job, you have my thanks.

[@terrywilliams6820]

Awesome video.. your awesome..

[@davidandlorinimmons2323]

Great information.

[@dlovand1]

Thank you for sloution. it helped me to find solution to my Citroen C5- 1.6 petrol. Other while this chaking could coast at least 70usd. Dlovan

[@larryleisuresuit9584]

nice i will try this

[@dfreedman2000]

Perfect! Thanks.

[@sawtun3294]

I appreciate your video,bro.

[@debracapuno192]

very helpful thank you

[@basilbenissan3656]

Great and Thanks

[@brendadomengeaux4867]

Thanks good video simple

[@OyeTequilla]

Thanks, that worked for me. Appreciate your vid.

[@mahmodabdulsalam99]

I appreciate your video,

[@daviddouglas7950]

Good man, thanks! Dave in the Adirondacks

[@rushanthjeyaram2443]

Thanks a lot It was helpful

[@karend4905]

Thanks for giving useful information & not boring me to death! I'm off to check my gas cap right now...

[@adatsang3668]

Karen D 冫

[@gordbaker896]

Disconnecting the battery in many cars can cause huge problems, especially if you have auto down windows and electric doors. Caddy XLR etc. Reset all controls - seats, radio, clock, mirrors etc.

[@javedahmad7513]

cool thanks.

[@irc6653]

thank you you are the Men!!!!

[@loupython3018]

Thanks for the video !

[@ironhorsevinnie]

A+ video, just wish you were my cool neighbor .

[@DraganSeculin]

Worked for me . Opel astra G ..thank you ^_^