Fantastic video, the world needs more content like this.
@joshuabenson2568 Жыл бұрын
Your shorts are always useful man, never change the format. ❤
@2strokeFORever Жыл бұрын
Nice a short that is actually a helpful tip. Cheers!
@displayedimagination9710Ай бұрын
Finally.. been looking for a video like this. Squeaky/Chirping suspension ball joints.
@nello86302 ай бұрын
Great way to isolate the ball joints and save a lot of money. Thanks for your time and effort.
@pauldennison254311 ай бұрын
This was definitely a worthwhile tip, thanks.👍
@richardp36244 ай бұрын
Great tip, Bubba. We never stop learning.
@RonBurgandy5 ай бұрын
Brother, you are a GENIUS ! I love your content ! Keep up the great work
@chrismannifield32224 ай бұрын
You can also evaluate the noise, is it an oscilating or linear. But youve shown something very important, that things should be tested in their operating positions. If the vehicle was on a lift hanging free....it may be dead silent.
@timbrwolf1121 Жыл бұрын
I've got a 93 dakota I just did the front end on. Replaced tie rods inner and outer. Wheel bearings, rotors, calipers, and upper and lower ball joints. Drove great with no noise anywhere. Got an alignment and now it groans while low speed braking and I can feel it in my brake pedal if I turn close to full lock. Kind of upset because I just did all that work, but I know I still need sway bar and control arm bushings.
@MrTravisAl11 ай бұрын
Wheel bearings sometimes get abused on install or not installed completely flush *especially if rust isn’t scraped off or if the machine press configuration isn’t aligned properly, or pressed too quickly. When any of this happens, they can make noise all over again and also wear out prematurely.
@timbrwolf112111 ай бұрын
@MrTravisAl they are tapered bearings and the fit was the issue. I was supposed to tighten it down. Rotate the rotor then back it off to finger tight and pin it. But I just pushed the rotor on and finger tightened it
@Samuel_el_toro4 ай бұрын
Get that creeper off the floor unless you are laying in it😂 from your Internet safety officer
@wjjproduction97153 ай бұрын
Idk how KZbin knew but I needed this video thx. But the noise from my car is coming from the back wheel what can I do to fix it
@Chr.U.Cas162211 ай бұрын
👍👌👏👏👏 Thanks a lot for sharing! Best regards, luck and health in particular.
@johnmiley56074 ай бұрын
Holy shit, Thanks dude. Amazing tip. More please! You rock.
@timreid95564 ай бұрын
That is a great tip! Thank you
@dariasmuradi68425 ай бұрын
Fantastic tip thank you from uk
@IvanGarcia-ft3zb3 ай бұрын
Great my 2003 Honda Civic hybrid had front suspension done and have some squeak when turning wheel
@Cultureshockcrew3 ай бұрын
Sick trick red! Thanks for the tip!
@FahimibnDawud7 ай бұрын
Actually a great tip! 👍
@kismofer122 күн бұрын
nice bro....another tip for learning...👍🏼👍🏼
@jenniferw50952 ай бұрын
My Suburban is squeaking exactly like this. Probably the upper ball joint. The lower ball joint is new.
@GROG-l7g4 ай бұрын
Killer tip thanks!!
@Freedom_Rider9154 ай бұрын
Looks to me that the ball joints have grease fittings. Someone is not doing their job. The grease fittings are there to prolong the life of the ball joint. Today’s cars don’t have grease fittings on them. You have to buy another part which doesn’t have a grease fitting on it either. I use a cattle syringe and heavy duty needle you can inject it into the boot which is rubber. Put a little caulking on it to seal water and grime out.
@matthewpeterson33292 ай бұрын
Great tip. I'm banking this one!
@williamhoward71213 ай бұрын
Nice tip, thanks!
@XalvaroramosX20 күн бұрын
GREAT VIDEO
@DGZMusic Жыл бұрын
Looks like he opted in for that valu craft.
@timothylevin26613 ай бұрын
It's like an orthopedic test
@Tony-rl2fr3 ай бұрын
But that's how my kids know not to come into the garage when mom & dad are detailing the truck.
@birdfrayser4 ай бұрын
Every profession has it's skill set...sets the amateurs apart from the pros
@adolfceazer47112 ай бұрын
Great one
@marcw18672 ай бұрын
How do you know it is not a tie rod end.
@lakeithwashum64973 ай бұрын
Got mine fixed last week.
@bmx1553Ай бұрын
thank you 🙏
@gxreaperxfigueroa5145 Жыл бұрын
Good job 👏
@gintsmiglavs75615 ай бұрын
That's genius, is there any other way to determine for the rear?
@pedrofrausto5395Ай бұрын
How much is the cost to fix that problem
@TheRepublicHasBeenLost Жыл бұрын
What specifically do you spray inside the bushing? Also, can you coat the bushing in something to prevent dry rot and cracking? I was told lithium spray. I use that on metal door hinges to great effect. However no sure about using it for lubrication of rubber. Thanks
@TechnicianRed Жыл бұрын
The rubber on the ball joint doesn't need lubrication. It's the metal ball inside that boot that needs chassis grease. You add grease with a grease gun through the grease fitting (if applicable). Most new vehicles don't come with grease fittings on any of the steering or suspension parts. The product I will sometimes spray inside to determine if the joint is squeaking is either PB blaster or Justice Brothers JB80. As far as rubber bushing lubricant goes, you want to use a silicone grease. Dielectric grease works but energy suspension sells a very thick version of silicone bushing grease that works better. The only bushings that need lubrication are sway bar bushings and any aftermarket polyurethane control arm bushings.
@B86432 Жыл бұрын
Leveling kit is the culprit
@connor3288 Жыл бұрын
I hate those.... Looks dumb to me, and messes up the front end geometry, as well as sometimes causing issues with CV axles. You think people who put those on their trucks are adjusting the headlights after? I think not! Think of how much worse the headlight aim will be with leveling kit AND loaded rear axle vs stock.
@jeremymajorАй бұрын
How to find a squeaky in the rear of the vehicle? Thanks
@justingregson32243 ай бұрын
witch one ball joint? Upper or lower?... It's usually the lower because of stress but video didn't help pin point a solution
@keneutervalve945911 ай бұрын
Useful, but you can also put your hand on it and feel it squeak.
@MrTravisAl11 ай бұрын
Doesn’t turning the wheel put many steering components into a new position?
@TechnicianRed9 ай бұрын
Yes, it does. However, I have never heard a tie rod end squeak when bouncing the suspension. They just don't have any load on them when the steering isn't being used so with no force being applied they don't make noise.
@connor3288 Жыл бұрын
Is this only for diagnosing balljoint noise? Does this also work for tierod ends? Usually squeaks seem to be the balljoints though, personally havent come across a squeaky tie rod end.
@MR..1814 ай бұрын
Been looking for the utube flick that had the exact squuuky squeel noise sound...misplaced it..
@letsgetitmindset5 ай бұрын
Dealing with this now 😢
@rigobertogervacio2235 ай бұрын
Nice
@pauleester Жыл бұрын
Great tip
@simonjones7785 Жыл бұрын
great tips thanks
@1oldskoolluvr Жыл бұрын
17 comments....and not one person is going "WTF?!! Front end work on a '24???" Unless he's clockin' 100K on it, seems like it's a lemon.
@TechnicianRed Жыл бұрын
2014, not 2024
@jamescameron7633 Жыл бұрын
Good knowledge bro
@BigRedChev6 ай бұрын
mine Squeaks when i hit bumps and turn the wheels, What would that issue be ?
@Thomas-xm5ym11 ай бұрын
Slick! Nice
@Scorchedvirtual Жыл бұрын
Cool video
@goldsilverjunkie11 ай бұрын
Smart!!
@stufoo3 ай бұрын
I just sprayed everywhere I thought it could be. Didn’t work.
@gussgates18322 ай бұрын
Ok tell me this my ball joints on my car are good and my car still makes that noise
@Gary-ce2hk4 ай бұрын
Boots my ass. Nonexistant boot is why joints are bad. Everything is junk
@randybloomfield5090 Жыл бұрын
Outer tie rods 🤷
@Workerbee-zy5nx Жыл бұрын
Gm front end squeeks, noisy since 55'😂😂😂😂
@ryanallen5334 Жыл бұрын
Idk about that
@Scorchedvirtual Жыл бұрын
Hello
@peted5217 Жыл бұрын
Poorly Maintained
@mrguy9885 Жыл бұрын
I mean I redid my whole suspension because of all of that that I probably would have just saved me if I would have just replace the ball joints, oh well it needed a whole new front anyways