A nice little upgrade to the backend with some illuminated signals/brake lights on the Tesla. Lights: amzn.to/3DcdbaH Model Y Model S Model X Model 3 Car Guru Automotive Cars
Пікірлер: 22
@oboys15024 ай бұрын
I try your method but I can't find where to fish the wire
@bachnghiem69204 ай бұрын
Thats my exact question. I did this yesterday and I had to open up more panels to fish the wires through the side vents. Took me way longer but I did it. This is a incomplete/wrong video to follow. There are other vids that show you how to fish the wires. Use those.
@jhom1952 Жыл бұрын
Thanks for the video. I have a set on order. I'm curious about how you were able to get the wire harness from the bumper lights up through the weatherstripping gap. Is there an opening near the taillight for the harness to go directly from the weatherstripping gap into the taillight cavity in the trunk for the taillight connector? I seen other installation videos that show a more circuitous route to get the wire harness from the bumper lights to the taillights.
@tims-garage Жыл бұрын
It is a bit circuitous indeed. The taillight has space behind it for the harness and you can squeeze a hand in there. The wire is small and can slide under the stripping if needed.
@weatherman8123 Жыл бұрын
I attached the wires before passing the wire transfer through the hole...Help.
@where5789 ай бұрын
The edge that the weather stripping mounts on is the demarcation between inside and outside. I used metal cutters to cut two cuts about 1/2in apart and 3/4in long to form a tab to be bent outward. I used heatsrink to toughen the wire at the crossover point and added putty to seal the gap. Over this joint, I used tape to hold the wire in place.... your mileage my very....
@Ughthisagain10 ай бұрын
Reflectors are required where I live so as near as this looks I can’t do it. Thanks
@OlegStasyuk3 ай бұрын
this is the best video for the install! There is a ton of them on youtube, but this one is the most efficient. took 5 minutes, the majority of the time was searching for misplaced tape:-} Thanks a ton!
@SeanManks3 ай бұрын
02:47 - Seems to shorten the video's time duration, he has completely skipped important step showing how you fished that guide wire to get to the wire down there. Also,, he has not shown any other steps just final result everytime he's done... bad video. 😒
@sstamp10120 күн бұрын
Right he casually skips the trickiest and most important step.
@nick07809 ай бұрын
I see the pins on the light side of the connector but where is the plastic housing/connector?
@myjamz4u4864 ай бұрын
Can this hooks up to a model S? The link you have to amazon said it’s for model y
@kexia Жыл бұрын
I bought the exact same one. But after installing it’s making all the lights blink when I put on the turn signal. Any idea why? The connections are simple. Don’t know why it’s doing that.
@tims-garage Жыл бұрын
Lose connection? Sometimes cheap wiring can be the culprit
@tcherny9 ай бұрын
Was removal of light cap nut really necessary? It seems from the video that by prying the liner there is enough space to put the hand in behind to reach the connector?
@tims-garage9 ай бұрын
Yeah, you don't have to
@kennethkim19 ай бұрын
Can I install it in the same way you did on my 2022 model Y performance? How long did it take to complete? Thank you!!
@tims-garage9 ай бұрын
I believe so - trim should not matter. About an hour.
@jaysay7333 Жыл бұрын
i can tell by his voice he is unhappy in his marrige, unfortunately.