Tesla Model 3 Bumper Bulk Wrap With Paint Protection FIlm

Bulk wrapping a aTesla Model 3 Bumper is challenging. However if you follow this guideline you should become proficient at it after a few installs. It’s great for those white finishes that collect dirt at the seams and edges over time.
Use a 36” wide roll for this.

[@noisydynamic2940]

Very quick and simple, a lot of people spend over 1 hour per car part while you do it in a breeze. Flawless work

[@jon-slem]

Best video I’ve seen. I’ve searched high and low. Thanks for making it. I’ve been afraid to do it. I’ve done pre-cut multiple times and I’ve been wanting to move to bulk, now I’m going to try it. I may fail once but I’ll keep going.

[@321PaintProtectionPro]

I Use STEK, and it has a weaker adhesive than what you're using, so my tension management is a little bit different for these installs, but overall this is a solid roadmap and quality walkthrough for this bumper for one piece. Nice work!!

[@PaintProtectionFilmAcademy]

Thanks! 🙏

[@JuanCarlosYes]

It just seems like the film obeys your commands before you even touch it. 😂 Very instructive - thank you 😊🙏

[@iconautoCDA]

Very helpful Ron, thank you sir!

[@toozwraps]

Slip solution is on point ! 👏🏼

[@mikesanchez1428]

My man!! I appreciate your super super videos!!

[@Dc5_henry]

The video I’ve been waiting for!!! 🎉

[@EncorePPFtint]

There are a lot of great helpful hints, tips, and tricks in this video. Even for a long time, installers like myself. Awesome video. 👍🏻 those air damns are always keeping it interesting. 😂

[@seednet]

Thank you for your technical sharing; I have benefited greatly.

[@EzDuZit2012]

I'm doing a first time DIY on my M3P. You were right about Xpel being different. I tried it that way and it definitely did not work out as well. Xpel Stealth is a completely different animal. I had to make a few extra cuts but right now i'm struggling with the fingers at the top of the bumper under the hood. I very much appreciate your video though. Thank you.

[@GR018]

Nice work. 👍

[@juanflores7394]

Thank u sir that is very helpful video...

[@Gulshan_patel_12396]

Nice work sir

[@Thesudstud]

Thank you

[@hosseinravan2610]

That's a great job bro . What attract solution are u using? It's sticky very fast

[@Cudiagraphics]

Amazing!

[@AbdulRehman-qp9kt]

Hi sir, Excellent work, i have some questions about “ slip solution or Tack solution “

[@user-nu2ff1iq7q]

very nice 👍🎉

[@ballplayer4301]

Learning so much off your videos, trying to understand the fundamentals

[@Bezpokraski]

Огонь больше выкладывайте видео !

[@PaintProtectionFilmAcademy]

I sure hope you liked it.

[@itsnayan8620]

What spray you're using, and where to buy it please

[@CertifiedTinter]

Looks great! What kind is blades are you using for trimming ? TIA!

[@PaintProtectionFilmAcademy]

There from NT Cutter I buy the hundred pack on Amazon look for NT Cutter BD2000

[@lalitda4011]

@PaintProtectionFilmAcademy I did install ppf DIY on my tesla and some edges there are pockets which has dirt and after cleaning it doesn’t stick back very well. Any suggestion you would give to get it stick? Will adhesive promoter help? Please guide. Thanks.

[@smanheat4019]

To learn with you

[@kevj9928]

What is your recipe for slip? I used the XPEL slip and Ultimate film and had a way tougher time with fingers and work marks whenever I lifted and repositioned. That gully in front of vent really kicked my ass.

[@PaintProtectionFilmAcademy]

XPEL adhesive is a little aggressive. If you’re using gel why not try a soap and water mixture.

[@user-tm7iq7hv8p]

Hello, may I ask how to mix the ratio of water and soap?

[@AbdulRehman-qp9kt]

We mostly use TPU, Now plz tell me how many drops are used for slips solution for tpu and tack solution and which one use alcohol or hot water????

[@Sid_Mowe]

What kind of spray do you use?

[@WokeAssYT]

What’s your slip and tack mixture and ratios?

[@AbdulRehman-qp9kt]

What Type of Slip Solutions or Tack Do You Use?

[@mikesanchez1428]

at 20:49....i almost saw your finger sliced and on the floor....mucho cojones mang!😆😆

[@AbdulRehman-qp9kt]

Which solution is best for each film?

[@kareemmohammed8720]

Excellent videos.I want install the tesla model Y front bumper i am not sure about size of wrap i need to buy?Do you have any idea

[@PaintProtectionFilmAcademy]

You can do it with a 30” wide roll but 36” would be a little safer.

[@shaikhnoaman13]

hi sir... great work I have a question , which type of material you used in ppf. it a TPH or TPU and which company ..

[@PaintProtectionFilmAcademy]

I use XPEL SunTek and Legend Film's I was using SunTek Ultra in this video. Hope this helps

[@jesseb2586]

WOOOO! First!

[@ryanrobinson5574]

What was the size and brand you used for this video? Thank you!

[@PaintProtectionFilmAcademy]

SunTek Ultra Tack 36” by 100”

[@1NATURELOVERJ]

What do you use for "tack"?

[@PaintProtectionFilmAcademy]

I use 6-8 oz’s of 91% ipa in a 32 oz spray bottle filled with water

[@sumanshek3259]

Hello

[@ivanobulo]

Don't use 3M Scotchgard for this install. It is much thicker and don't stretch enough.

[@isffilm-ppf-windowtint]

Thanks sharing,really useful!!!Congratulations from @Isffilm.