THAT WAS HARD TO REPLACE

[@ehcatsfaneric2211]

Your mechanical knowledge sure saves you LOTS of money pal! PLUS you know the work is done right.Your parents must have instilled in you a great work ethic. Truck on buddy

[@Montoya1991]

Bro youtube is great for diy work. Just gotta buy the tools and dont be too afraid to do it. Take a chamce

[@banzaii6285]

If the compressor was pushing oil, check the air dryer, and at least change the filter and clean it out. Make sure the purge valve is good too (not expensive), that will F up soon as it gets real cold. 👍 Good job.

[@sarahmoller9716]

You do so much work on your truck and hard to tell how much money you are saving yourself. Amazing what you are willing to do to keep yourself on the road.

[@kens.3729]

Hello Rasim! Just talking about you this AM at my Dentist. Hygienist BF is an OTR Trucker. 👍

[@kens.3729]

If you don’t work on your truck yourself, you’re not paying the Bills which always stack up. 👍

[@arnoldramos39]

Great video thanks 👍

[@juancerritosalmeda7120]

Yeah keep maintaining your truck and yeah you should be able to you know be good with your updates but yeah just keep doing what you're doing

[@youtubeisawesome2487]

gasket maker and silcone (starts to set up when air hits it)are two different things, gasket maker (grape jelly anaerobic sealant) will not harded unless the air is cut off (smashed between two parts), 60 series is one of the easiest air compressors to do, your valve cover is most likely the football gasket or cam caps leaking, to get the valve cover off just push the pipe over with one hand, if your hoses are good no worries, if it is hardened you might want to replace it, clean (drain) the ping tank daily for a couple of weeks to get the oil out of your system, then install a quart of air brake antifreeze in a tank and prepare for the winter, it only takes a small amount of oil to make all the rubber parts in your air system break down and leak,

[@bostarbird5282]

Do yourself a favor and never reuse those spring type hose clamp. They get weak after awhile and with pressure on the hose it could back off and dump whatever is in the system. Not worth the savings of a $2.00 gear clamp in my opinion. Thanks for the videos.

[@otrookie]

Yea I replaced them all

[@markjones2960]

Did you go back with the 550 compressor or did you go with the 750

[@zahidkhurshid6234]

Hey man great video. What's that small airline right above the air compressor going to gear housing mine is is broken off

[@otrookie]

Sorry way late response. Would be your fan clutch air supply

[@luisvazquez754]

Nice job man 👍🏻🔥 Do you mind adding the link to the reman air compressor.

[@PeeJay561]

How many bolts hold it there in the front? I'm actually doing mine now I just about got it out but it feels like 1 is still holding on

[@noahater5785]

Aside from your old leaky air compressor being difficult to remove due to the sheer weight of it at 70 lbs, that must have been one quick and easy job.

[@streetglide_24c62]

Fresh rebuild and the valve cover is leaking I’d be worried about the mechanic ability’s that inframe on the engine.

[@willmann30]

I have to agree. For a fresh rebuild he is wrenching too much on that non emission block. I understand sh*t happens but damn.

[@vitiman612]

Good job

[@remotecontrol2835]

Wouldn't putting a old gear on void the warranty?

[@otrookie]

I’m not too worried about warranty really they also said no gasket maker it voids warranty, using paper one I’m just not a fan of

[@nba_sheye6426]

What’s a good tool kit to carry with you that you use that can handle all that ?

[@otrookie]

www.ebay.com/itm/TEKTON-60PC-1-2-DR-DEEP-IMPACT-and-SHALLOW-SOCKET-SETS-SAE-METRIC-6-POINT-/303512866072?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=711-127632-2357-0 www.ebay.com/itm/NEW-Husky-270-Piece-Tool-Set-w-Case-SAE-Metric-Sockets-Wrenches-Ratchets-/124983381066?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=711-127632-2357-0 And bunch of Milwaukee m12 fuel tools

[@xdeadwaitx]

I just replaced my stainless line and it most definitely not $50-$60 bucks. It was $310 before tax.

[@crazyturtle16]

2024y - $1325 Detroit rebuild

[@Pokingthebear999]

Rasim, Do you have to, timing to TDC?

[@otrookie]

What do you mean

[@banzaii6285]

No, just put it back in....the compressor.

[@EddieTruckingAdventures]

Hi. Hope you are doing well

[@otrookie]

I’m good! You as well

[@EddieTruckingAdventures]

@@otrookie good thanks

[@mb6060]

Why no shop for even the basic needs ?

[@otrookie]

What you mean

[@jerrybreu5997]

1st again, OT🚚

[@robbwhitehead5486]

You should of removed the intake for better access