Metal Corner Bead Installation & Mudding - BEGINNERS GUIDE!

[@Flysimware]

When it comes to teaching carpentry, you're my favorite.

[@TheExcellentLaborer]

This comment really does make my day! I appreciate that. I really do enjoy teaching through KZbin videos. Stay tuned for more!

[@wiiz2780able]

I approve your message

[@rudyrivera7426]

👌👍

[@yassirc3681]

I love this channel. You explain every detail making the process so easy to understand and implement. Many thanks 👍

[@TheExcellentLaborer]

You are very welcome. I’m glad you love my channel! I’ll try to keep everything very basic and simple to comprehend. I appreciate you watching. Good luck with your project!

[@BeautyCarriers]

That channel makes me save a lot of money, I learned a lot. Thank you so much.

[@cassidyamadi4003]

Your job is always wowed. Thank you for all your videos

[@TheExcellentLaborer]

You’re welcome. I’m glad you are finding value in my content. I’ve tried to upload every week or so. Stay tuned for more!

[@MyClutteredGarage]

Nice job and excellent production quality! -Ed

[@TheExcellentLaborer]

@@MyClutteredGarage Thank you Ed!

[@doatoolate.1250]

Good video. We use Mesh tape on the corner bid between metal and sheet rock to prevent future cracking.

[@TheExcellentLaborer]

That sounds like a great way to add security. Good idea. Thanks for sharing!

[@jtlachappelle]

Excellent, thanks man

[@TheExcellentLaborer]

I appreciate that. You are welcome!

[@elyoryarchila5666]

Thanks buddy, first time doing that

[@216Clevelander]

I usually start from the center instead of at an end to prevent fold ups

[@JayounHeo]

Hi, thank you for the helpful video! I have a question about keeping corner bead level and plumb when the drywall is not installed in good condition -how can I ensure it stays really straight? I find it hard to use a laser level every time I work on corner beads in Condo and townhouse unit. I’d really appreciate any advice you can give me about leveling without using the laser. Thanks from Toronto!

[@corygreenwood384]

You should make a video on how to frame the corner of a room

[@TheExcellentLaborer]

This video I made in the past might help kzbin.info/www/bejne/gJzTnXmNbLx7iNk . Thanks for watching!

[@corygreenwood384]

@@TheExcellentLaborer yea thank you keep up the good work love your videos very helpful

[@jchase1702]

Great video! I need to install corner bead on window frames. Can I use Spax waffle head screws?

[@Keeps-]

How does the corner get mud if its scraped off?

[@TheExcellentLaborer]

It never does get covered in mud. You typically just paint over it. The metal corner is embedded in the mud for the most part except for the very corner. I hope that helps!

[@shannoncooley2112]

How did you mud those beads that were closer than 9 inches?

[@justinlarsen4631]

Hi, I am trying to replace some water damaged drywall in the bathroom. The piece is about 16"x3 1/2". One side buts up against an acrylic tub and just floats over the flange. The other side runs under a now partially rusted corner bead. I rent, so I am not going to replace with tile or Hardiebacker. I am just trying to figure out if I can get a 16" replacement piece of corner bead to match the profile of the undamaged portion of corner bead that is still on the wall, or will it be a fools errand? Can i replace just the bottom portion of bead with vinyl to prevent rust? Will that make it harder to match? 2nd Can I run mud directly over the flange into the side of the tub, or do i need something like a Trimtex tearaway bead to prevent mud from cracking overtime due to temp fluc. and the mov. of the acrylic tub. I was honestly thinking of using a piece of pvc baseboard instead of drywall for a patch, so I take care of the waterproofing issue. But that's just because I'm forced to buy an entire sheet of Green Board when I am using less than a square foot. Thanks in advance for any advice.

[@mikemiddleton8847]

A: do all your taping 1st. B: start in the middle and use nails C: tape the corner to prevent cracks D: mud from the bottom and work up E: get rid of the gloves.

[@JeffWaldner]

Where do you live ?

[@blackhorse2947]

Sorry……. 76yo didn’t have my glasses on…. I thought the title was Corn Bread……

[@maintenancebynathan2150]

If you spread joint compound on your corn bread you won't need to use tooth paste ever again.😝

[@taylorsessions4143]

You guys are my kind of people 😂

[@AndrewAce.]

🤣

[@joshualambert8346]

😂😂😂