Excited to share my best doorknob installation tips after literally thousands installations! Thanks for watching:)!
Пікірлер: 144
@ellianaschlabachh4 ай бұрын
I was trying to be independent and do this, but I installed the latch and the door plate, I then shut the door and it latched, and I had no doorhandle obviously, so now I’m freaking stuck in my room and I don’t know what to do😭💀
@guyidontknow433 ай бұрын
this person Is still stuck in their room
@DeeGalvinn3 ай бұрын
rip 🕊️
@tiffanys62832 ай бұрын
I almost laughed way too hard! Sorry 😂😂😂
@Dawoud_ShirinАй бұрын
If u have one of the handles you can stick it in there to open it. I did the same thing but I didn't lock myself in 😂
@corpingtonsАй бұрын
@@DeeGalvinnlol how’d he type thjs
@ronlicari5403 Жыл бұрын
What door knob is that I need black without strike plate?
@kirkyhopwood2815 Жыл бұрын
Whats measurement
@KneelB4NoMan2 жыл бұрын
Was really hoping you’d show the more “standard” type doorknob. The kind without the “beauty plate” which covers the screws. Does ANYONE have an easier way to remove/replace those dang two screws?? The angle you that you have to attack them at, due to the knob being in the way, makes me lose my shit EVERY time!🤦🏻♂️
@franzruberl15832 жыл бұрын
Please answer or address this! The WORST doorknobs.
@isaiahii69822 жыл бұрын
Most modern knobs will have a set screw that you can loosen so the knob comes off and gives you direct access to the screws. If the knob you are dealing with does not have this, then all you can do is use a long bit that gives you the best angle to the screw head.
@edjohnson5840 Жыл бұрын
Fails to show how to remove the flat plate.
@MoeLarryTheCheese Жыл бұрын
What a great video. And what a great explanation. No constant "go ahead and", "go ahead and", " go ahead and" verbal filler over and over and over. Just the instructions on how to do the job. Subscribed!
@regularguy92642 жыл бұрын
Good video as always. For repairing old holes, I use glue and a golf tee. Tees are made from hardwood and they break off flush when you hammer them in. Then you can re-drill the holes, usually with a self-centering bit. Sometimes I have even had to use some blue thread locker on old handles when the screws keep coming loose. Lots of good advice as always.
@imover9999 Жыл бұрын
I always used wood glue and toothpicks, but I definitely will store this tip in the ol noggin to use for next time I need it! Thanks for sharing this!
@familymohlman23665 ай бұрын
The golf tees of the old days (the wood ones) are like gold for your toolbox for door repairs.
@leighgraham Жыл бұрын
Just in case you used the impact and strip the screws in the frame, wood filler does a nice job of fixing that...I know a "guy" who did it...
@zupmeoff2 жыл бұрын
You can adjust the latch? 🤔 I never realized that 🤣
@eternalfizzer Жыл бұрын
Cutting off the tip of the screw is removing the wedge that splits the grain.
@BobbySoria-e8t7 ай бұрын
I install door hardware everyday for my day job, to keep the door for rattling you always want to adjust the strike plate by moving it back a little, yes you can bend the tab but you never want to bend that too much because it just looks unprofessional, so moving that strike plate back and the cutting around and chiseling out the excess is the way to go.
@TheFunnyCarpenter7 ай бұрын
That’s an excellent tip, thanks Bobby.
@christines19242 жыл бұрын
BEAUTY!! good demo. Just changed out door mech to TouchPad and that was a trip. Got to chisel out areas 😵💫 all good and it works!
@babbubajwa114 ай бұрын
Do you have a hack if vanity knob screw gets rusty and not opening?
@stevestevenson32528 ай бұрын
I am so glad I found this video. Huge help to me, didn't know I could slide it over to make it longer. I bought 4 different locks the past month thinking i was buying the wrong type lol.
@danfrain16 ай бұрын
I bought a new lockset once before I learned that changing the key (up/down) orientation was as easy as it is. I don’t do enough of it that I can remember how, but I know it can be done.
@Iconic_hamza4 ай бұрын
Agreed, best video ❤
@resecurelatch10 ай бұрын
For what I have seen maintenance techs do in my almost 20 years in property maintenance, this one is common where they would just strike the latch with a hammer or channel locks. Then they wonder why the latch wont retract. Great advice for using a piece of wood to equal out the pressure. For anyone having an issue with their door latch or deadbolt, property maintenance or DYiers, there is a new solution that replaces Glue, Sticks, Puddy, or that ugly metal sleeve that goes over your door. ReSecure Latch sits INSIDE the door bore hole, alongside the latch, and the supplied screws thread into it. Works with many of the top brands like Kwikset, Defiant, Yale, and others. After watching the many videos Funny Carpenter has on DYi repairs, come check out how it works. Hopefully one day to have in inside box stores like Depot and Lowes.
@BlkFireHawk42710 ай бұрын
Where can I buy one of these. I have that problem and the sticks didnt work long. Can't find them on HD or lowes website.
@HannaHunt-o4t8 ай бұрын
I have a handle style. Everything seems to fit well, but when I go to put the screws in, they dont seem to reach enough. Could this be the depth of the hole/door is too long for the specific door handle I purchased?
@peglamphier47455 ай бұрын
Dude, Thanks! My husband's out of town and I've got 6 knobs that just came in the mail for my basement build and I'm going to try to do them myself. After I get my two hours of floor tile grouting done.... It'll be more fun than grouting.
@Denny_7782 Жыл бұрын
As a locksmith, I really appreciate these videos in regards to install technique. The sagging top hinge fix video is another favorite of mine so far. Thanks for the laughs AND tips!
@GojiraY2Jake4 ай бұрын
This has to be one of my favorite videos to explain how to install or fix something, it is so simple and the video is not 20 minutes dancing around what needs to be fixed. Thank you.
@vashon100 Жыл бұрын
3:40 what is that type of door latch called, trying to find the circular type rather than rectangular type?
@garybecker44902 жыл бұрын
When i dont have a scrap of wood handy to push the latch in, i use a socket. Just like tapping in a bearing.
@acdavis1980 Жыл бұрын
Definitely saved me on this one thanks for the helpful tips. I'm used to the 2 piece doors knobs.
@RushMayo Жыл бұрын
Painters tape helps hold the knob to the door while installing
@RPmusic062 жыл бұрын
Great video as always bud!!! installing door knobs here in the Netherlands is much easier and im glad 🤣 still some really great and useful tips bud, love the video!!! have a great weekend bud!
@TheFunnyCarpenter2 жыл бұрын
Thanks Rushill, hope you have a great weekend to🍻🇨🇦
@huyked Жыл бұрын
I feel like a complete man now. I was only half complete with your other video: taking off a door knob. Thanks! Me, man. Roaaarrr. xD
@BrockleeSwag9 ай бұрын
Me struggling with lock then wondering what im going to do because it seems the handle doesnt fit. Then I find this video. "This part right here expands" Thanks a bunch was able to get it working just from that.
@derekrobertson15482 жыл бұрын
The point of the screw pushes the fibers of the wood apart causing spliting, when you remove the point the screw is actually severing the fibers just as a drill bit does. The same trick can also be applied to nails hence why the older type nails had a square end to them amd did not slit the board.
@josephppopp7493 Жыл бұрын
Your a Saint, I wish, I saw this before my twenty doors. Fantastic instructions!!
@shaniasteinmetz8255Ай бұрын
Hi! I was hoping you could explain how to replair and replace latches and knobs for old houses where people butchered the wood? Like theres a large hole from a long old fashioned latch and they put a small plate over it and didnt fill it in or anything?!
@philipdanieljones99482 жыл бұрын
I put oak doors on and that is a different ball game these have glass in aswell one mistake and your f**ked took me a hour and half each door very hard and the doors to hang and line up were a task because they were so heavy
@TheCoolFilm Жыл бұрын
Thank you, this was perfect information. I do have a trick on how to find the right areas to fit the 2 long screws into place; use a greasy pen to mark the center of the hole right on the door, this will guide you putting the knob in the right position. Once in, you can just wipe off these marks.
@jasgarcha28412 ай бұрын
The reason cutting the screw works as drill and not breaking the wood is because of the formula area is inversely dependent on pressure. Less area of the screw that is the tip on the screw puts more pressure that breaks the wood and when the tip is cut the area becomes more and that eventually puts less pressure on the wood.
@Chris.J.A.B4 ай бұрын
Thank you. Question, just replaced handles not knobs. So much freeplay in handle. Is there a way to tighten or did I simply buy low quality?
@jaredevildog63432 жыл бұрын
Great tips. Thanks for another helpful video. Please keep em coming. 👍
@TheFunnyCarpenter2 жыл бұрын
Thanks buddy, 🍻🍻I appreciate the support!
@johnburns29402 жыл бұрын
Thanks dude clear and compelling delivery 👊
@burtreynolds6163 Жыл бұрын
I love your videos! You don't waste time with silly introductions and "entertainment." Very helpful!
@michelduron12177 ай бұрын
Attention au français qui regarde cette vidéo le mètre est gradué en pouces. Il faudra multiplier par 2,54 pour avoir les centimètres
@karchata71232 ай бұрын
I thought you were about to say check out this video in reverse for removing the knob in 25 seconds😂😂😂
@wendycol83543 ай бұрын
What do you do if the door shuts with tne mechanism in when you havent put on tbe handle? We can't figure out how to open the door. Mornings working so far.
@gerry71395 ай бұрын
be careful. some backplates are screw-in. dont PRY. they might loosen counter clockwise or clockwise too.
@yokanshree462126 күн бұрын
The only part I needed from this video 5:12 I just had to pull it back alitte to see
@maplebob232 ай бұрын
Where did you get that latch? The only ones I can find have strike plates. It’s evil.
@yourmasterrenovator867 ай бұрын
Amazingly helpful hints man! Specially manipulating the strick plate with screw driver!!! I didn't know this one. Thank you so much for teaching this. I'm grateful 🙏
@kauaireed90065 ай бұрын
If you wanted to, could you put a deadbolt in that same hole instead of just a privacy lock knob thanks so enjoy your videos
@diyamerican2 жыл бұрын
Nice, thanks I learned something.
@MYMusicMYLove3 ай бұрын
Is there antway to extend my latch bolt? It's shorter than my other one and my door isn't locking
@0.sashaa3 ай бұрын
thank u, my dad did 3:33 wrong he left the thing loose which caused my door to not close but now its all good😭
@davidgibbons9595Ай бұрын
Excellent video! Thank you so much!
@hermanmoreno92178 күн бұрын
Well said. Great job!
@darrenstettner538129 күн бұрын
Omg! Thank you!!!! That part about the latch mechanism being adjustable is a detail I’ve just watched around 20 videos trying to find out. Everyone mentions that you need to set the jig to 2 3/8” or 2 3/4” but no one mentions anything about how tf im supposed to know which one. It’s such a tiny detail but as someone who knows nothing about this, it needs to be explained. Seriously fkin aggravating that so many tutorials left that one essential detail out. Thank you!!! Such a relief to finally have it explained. Fk all those other instructionals. They are all useless without that part.
@sweetsushanna-ahh Жыл бұрын
Excellent tips, love the hammer and board tip. I don’t have a drill but I may consider getting one. I haven’t changed a doorknob in a long time but I think I will change my front doorknob soon so appreciate all these tips.
@JohnSmith-ef6rg Жыл бұрын
Thank you.. do you have a link to the door knob? Looks very nice...
@peterpumpkineater696563 ай бұрын
hell yea great video it helped me get it done in less then 5 minutes
@maplebob23Ай бұрын
A broken doorknob really makes me hate doors.
@Pete.Ty12 жыл бұрын
👍👍👍
@TheFunnyCarpenter2 жыл бұрын
Thanks Pete
@jerrywielo2952 Жыл бұрын
What do you do when doors are slightly misaligned with their frame? I have brand new doors installed by the builder and can see that few of them are missing by a few millimeters and of course that is enough to not lock them up properly… all of them seems to be lifted, not sure if this is something every builder does because with the time doors will go down…(gravity always wins) do I need to tweak them on the hinges or reposition the plate? Thanks for the video!
@chadclca12 жыл бұрын
I’m usually right on the same page with all this guy’s methods, but I put my striker plate on last. I’m even skeptical enough at my age to screw in the top screw of the plate, check it, then if I’m happy finish it. It’s more common to see MDF jambs now, so if there are any adjustments to make, having the whole plate on puts you in that awful “just off the existing hole predicament.” I think I’m checking each door because painters either jamb the stop with dap, or they paint the door using those dang rebar chairs stands or sawhorses. Basically wetting an already extra absorbent particleboard door, tipping on its side and letting gravity make a nice little bow. Tapping stops around and moving the striker plate in and out is the price for a perfect click.
@tedsobocienski7872 жыл бұрын
I agree. I usually put the striker plate on last. I attach with one screw to make sure the door catches properly. Many times I've had to raise or lower the plate and I don't want to make a lot of holes.
@FiveFifteen8 ай бұрын
Exactly what I needed, thanks! Except one piece.. I don't have a mortise for the strike plate. Do you have any tips on cutting that correctly? Thanks for all of your content.
@juliea.Ай бұрын
Excellent, thank you.
@lizzkopta2 ай бұрын
Can you just, remove the latch plate from the new door knob? Or do you need to buy a special kind of latch plate-less knob? My doors are like the one you’re working on in this video, and I can’t find any door knobs for sale WITHOUT the latch plate. 😅
@spystalkerАй бұрын
Most knob sets come with a removable latch plate so you can install with or without!
@murdithmclean6044Ай бұрын
Excellent video. Saved me with the tip on the way that the insert has to be adjusted to the open position for privacy locks. This rescued me from bafflement when the lock didn't work and nothing in the instructions warned about this. Invaluable.
@stankrajewski8255 Жыл бұрын
I have witnessed the quality of passage sets drop, and the prices for quality hardware drop to a very low bar. Take your time to test, test, test how your passage set and latch are functioning as you install them, no matter how much you have spent on the hardware.
@tonyabishop765611 ай бұрын
I cant line up the two screws that connect the back faceplate /bolt and lock key thing....arghhh are there any tips , if i just line up one screw is that good enough lol ?
@khalidsami8606Ай бұрын
good video. straight to the point.
@reebokchelsea9591 Жыл бұрын
The latch when you switched to the round instead of the rectangle piece. Mine that I'm trying to change has the round in the door how do I pop it out so I can put new latch mechanism in? Having troubles!
@johnwebb44996 ай бұрын
Your door knob is different than mine. It is taking me hours to figure out and I have instructions.
@SimplyNicoleS3 ай бұрын
Thank you so much! This video gave me the final piece needed to finish installation! I was just about to live with the fact that my door knob would never turn again😂
@epiclight858 Жыл бұрын
How do you remove the driving latch?
@TheFunnyCarpenter Жыл бұрын
I think I have a video on that on the channel.
@nochin8783 Жыл бұрын
my problem is the back set has too much of a rectangle shape and wont fit in the round hole... i do not own a router
@themeat50532 жыл бұрын
Did you borrow that hammer from your kid?
@TheFunnyCarpenter2 жыл бұрын
😂🍻that’s my hammer for finish carpentry. I like it because it’s small.
@charlesbuettner5717 Жыл бұрын
Where can I get the knob sets with the circular bolt? All my doors have that older system.
@HendraG-nn1gi8 ай бұрын
Thank you very much for this great video...
@loxalot312 жыл бұрын
Drive-in latches and bolts are a bad idea. Over time the hole they are in will get larger then the latch has excess movement which can cause damage to the lock and mechanism plus the door will rattle more and the strike will not line up correctly.
@MarketLabBiz1013 ай бұрын
Awesomeness,Thanks : )
@SocialistDistancing2 жыл бұрын
I have on old exterior door that had a latch like that. It finally broke after decades and I could not find a replacement for it. I gave up and had to get one with a plate. I bought a ryobi jig to recess the plate. It was a bit of a challenge and maybe not the best or prettiest job but it works.
@cb73 Жыл бұрын
Do you have a video for making the hole for the strikeplate?
@huejanus5505 Жыл бұрын
I usually screw the striker plate on backwards, so it will sit flush, then i cut around it with a utility knife. This way it doesn’t move around when you’re outlining it.
@trig2 жыл бұрын
Door Knobs, havent you guys heard of Archimedes?
@paultech93852 жыл бұрын
When you cut the end off it no longer acts like a wedge but more like an auger.
@amatodellavechia6859 Жыл бұрын
Thanks for this video..I've installed many but never knew about that plastic adjustment thingy..nice tips for us dummies thanks again...finally got the knob to sit right...
@alivc2458 Жыл бұрын
Appreciate your help, very informative video :) Thumbs up!
@christinaroot59107 ай бұрын
Thank you thank you thank you!!!!
@VM-oi3dk3 ай бұрын
Totally different
@hellcreekoutdoors Жыл бұрын
Idk who put mine in but I can't get that thing out to save my life.
@annettepilgrim96262 ай бұрын
THANK YOU.
@richspring1 Жыл бұрын
Good, thoughtful vid work.. Thanks.
@donnaskelcy Жыл бұрын
Your videos are so awesome!
@TheFunnyCarpenter Жыл бұрын
Thanks a lot for the support! I'm glad you're enjoying them:)
@walnutcontractors56612 жыл бұрын
Like the strike plate tab trick - I'll have to try it out ! Keep physically sane we'd miss the weekly installments.
@sandratofte2392 Жыл бұрын
Our doors have the rectangular plate around the latch on the edge of the door. Ours have square corners and the ones on the new door handles have rounded corners. Any suggestions for what to do?
@charchar23757 ай бұрын
Now how do you remove that
@KarinaPolicy Жыл бұрын
Are you single? 🤤😍
@skhalid6597 Жыл бұрын
Can you please share a link for door knob?
@malanalan1 Жыл бұрын
My secret is to replace it with same brand
@acreguy315611 ай бұрын
Well done, sir!!! Thanks.
@sherrillyoung52206 ай бұрын
Thank you
@EonSlumber10 ай бұрын
This helps a lot. We’ve all done deadbolts and stuff but to see a pro is great.
@johnbeswick67472 жыл бұрын
GREAT information as always. Thanks
@wm213207 Жыл бұрын
What’s the brand of the door know
@christosv2291 Жыл бұрын
always a clear well produced video sir, thank you.