How to remove and install a timing belt on a 1994 Toyota Tercel Sedan with a 1.5L four cylinder engine.
Пікірлер: 95
@eduardomontoya38084 жыл бұрын
I believe u cover this better than anyone else, thumbs up twice
@benr7965 Жыл бұрын
confirmed this is more difficult in the car, due to not having clearance to get a puller on the crank dampener. However, i don't believe its pressed on like some other cars I've worked on. Tap it with a hammer and it should come loose. be careful not to damage the pulley with the hammer though. Thanks for the video
@talpatalpa11353 жыл бұрын
Gracias
@user-lm3rl2gn3jАй бұрын
Good Job
@denisd51823 жыл бұрын
Can this only be done with the engine down or it can be done with the engine still mounted in the car?
@InitechAuto3 жыл бұрын
This is supposed to be done with the engine in the car. The engine was out so it’s just for illustration purposes only
@talpatalpa11353 жыл бұрын
Buen video
@joebarone32728 жыл бұрын
I think I can do this in 13 minutes and 26 seconds!!!!
@miguelangelgonzalezcorrale32289 жыл бұрын
hola me gustaría saber la coordinación de las mangueras de vacío en la vsv veo que le sabes muy bien a la mekanika y tengo tercel 93. motor 3e-e espero contar con su ayuda
@hamishmartin442020 күн бұрын
Where does someone find the torque specs? I cant find a haynes manual for 1999 year? ( i know this is a diff year)
@dw4940 Жыл бұрын
My belt snapped while driving. Is the procedure any different in my case?
@InitechAuto Жыл бұрын
No, just line up the timing marks and install your new belt.
@bobhunt595 Жыл бұрын
@@InitechAuto thankyou for reply. Enough procrastinating on my part, I'm getting ready to tackle the job. Never replaced a timing belt before
@rodneyarmstrong38133 жыл бұрын
You don't need a puller for the crank pully it's not a press on. The trick to hold the cam is called cam locks.
@InitechAuto3 жыл бұрын
Camlock‘s is not a trick. It’s a tool for a specific task. I think my crescent wrench is more of a trick. 😁 As far as the crank puller. Not all of them just slide off. And as soon as you run into one you’ll wish you had the Puller. The puller is for demonstration and it’s a good practice to have.
@scottduguid34533 жыл бұрын
Mine wouldn't come off last time I did the job and I broke a piece off the pully by using one of the jaw-type pullers. I actually used it anyway and it's now time for another new belt - I'll replace the pully this time but will still use the proper puller if I need to, when removing :)
@rebeccagarcia58635 жыл бұрын
What type of alternator is this? I need to replace one for my '94 tercel and can't figure out the amps I need or whether it needs a heat shield or not. Thanks!!
@InitechAuto5 жыл бұрын
The only advice I can give you is to remove the alternator and take it to an auto parts store and have them match it up. I really don't think you need a heat shield.
@rebeccagarcia58635 жыл бұрын
@@InitechAuto thank you for responding!!
@antoniosilveira36606 жыл бұрын
That job is a lot more difficult when the engine is in the car , by the way the two bolts for the valve cover are 12 millemeters not 14
@InitechAuto6 жыл бұрын
This has to one of the easiest timing belts to do. In or out of the car.
@joebarone32728 жыл бұрын
This has got to the easiest timing belt job ever !! Right now I'm in the middle of pt cruiser turbo timing belt....worst car to work on EVER! ! !
@InitechAuto8 жыл бұрын
I feel your pain...PT is not mechanic friendly.
@joebarone32728 жыл бұрын
+Carlos Cuadra I think Area 51 would have trouble jeez
@franciscosaldanaacosta8127 жыл бұрын
le quedara el frente de toyota tercel 96 a un 92
@InitechAuto7 жыл бұрын
No se
@christophermckinnon49202 жыл бұрын
a little advice please, my 95 tercel seems to have a tapperd ID. The balancer only easily installs one way, an the keyway doesn't touch. is it being installed backwards?
@InitechAuto2 жыл бұрын
As far as I know it only goes on one way. What is tapered? What ever gets it closer to the engine is the way it goes.
@christophermckinnon49202 жыл бұрын
thanks for your response
@betoramos75013 жыл бұрын
Hola Carlos, es cierto que este motor 3E con caja mecanica rinde hasta 80 km x galón? Saludos desde Perú.
@InitechAuto3 жыл бұрын
Por lo que sé. El kilometraje debe rondar como 46 km. por galon de petro. Saludos desde Arizona, USA
@alexanderbarrera91404 жыл бұрын
Im trying to put the belt on but its just barely able to get on and i have the tensioner locked fully back in position. Any ideas?
@InitechAuto4 жыл бұрын
Make sure its the correct belt. Don't let the tensioner fool you. It can move just enough to make the belt installation difficult. Also try rocking the cam back and forth to get a little clearance.
@alexanderbarrera91404 жыл бұрын
Nicoya i figured it out. The camshaft needed to be rotated like 2 cm to the left and the teeth lined up better on the belt and gave me just enough to get it on. So for your future advice thats another tip. Line up the pulley teeth to maximize full belt length. Thank you for your help.
@juanmiranda45217 жыл бұрын
Carlos tengo un Tercel 1993 y tira humo Azul al encenderlo en la mañana pero cuando calienta no tienes ese problema hasta el proximo dia que lo enciendo Otra vez.
@InitechAuto7 жыл бұрын
From what you are describing. It could be bad valve seals.
@juanmiranda45217 жыл бұрын
Thank you .
@bebobalaquer83938 жыл бұрын
carlos y para cambiar el filtro de la gasolina prendo el carro le saco el efi y dejo que se apage solo.mi proyecto en areglar este carro y el manual no lo consigo
@InitechAuto8 жыл бұрын
No entiendo la prequnta. Para cambiar el filtro. Aflohase los tornios despasio and deje que salga la gasolina. Y se cambia el filtro...es muy facil.
@bebobalaquer83938 жыл бұрын
+Carlos Cuadra ok I just wanted to do that and not spill to much gas
@francois5498 жыл бұрын
Thank you !!!
@sonofthedeathsergio7 жыл бұрын
tengo un toyota tercel 93 y tiembla mucho el motor cuando meto el cambio en P y en N no tiembla que pdria ser?
@InitechAuto7 жыл бұрын
No se, Check your tune up condition.
@nowornever14143 жыл бұрын
When do you change the timing belt ?
@InitechAuto3 жыл бұрын
Check with your vehicle manufacturer's maintenance schedule. Some can be as short as 50k, while others can be 100k.
@diyathomeagain66168 жыл бұрын
Where is the water pump? Shouldn't it be replaced as well?
@tomb8165 жыл бұрын
It's the top pulley on the alternator belt path. Yes, it should be changed w/ the timing belt replacement.
@scottduguid34533 жыл бұрын
@@tomb816 Also not a bad idea to do the crankshaft and camshaft seals while you're in there
@jackwainscott63437 жыл бұрын
How do you know if the 3e is directly in the exact right point?
@InitechAuto7 жыл бұрын
When its at the 12 o'clock position.
@jackwainscott63437 жыл бұрын
how do you know when it is exactly in the 12 o clock position, I say this cause the engine is a little at an angle, so I was trying to get it perfectly in the right position.
@InitechAuto7 жыл бұрын
Jane and her three little sisters 12 o'clock in relation to the cylinder head so if it's at an angle 12 o'clock will also be at an angle
@antoniosilveira36606 жыл бұрын
3e is at the right point when you look through the hole below , and you see a dimple in the camshaft bearing cap
@applepoop107 жыл бұрын
Do you have to remove the engine to change the timing belt?
@InitechAuto7 жыл бұрын
No, I was replacing the engine anyways.
@applepoop107 жыл бұрын
Carlos Cuadra Ah okay. What happened to the engine?
@InitechAuto7 жыл бұрын
This was a replacement engine...the other one had a oil consumption problem...oil rings stuck.
@applepoop107 жыл бұрын
Carlos Cuadra That's the same problem in my 1994 Tercel but that was the previous owners fault for not keeping up with the maintenance.
@rogerlee6929 Жыл бұрын
What if timming belt broke
@InitechAuto Жыл бұрын
Line up your timing marks and install new belt.
@rogerlee6929 Жыл бұрын
Do i have to take off all that stuff like pullys tentioner stuff like that
@InitechAuto Жыл бұрын
@@rogerlee6929 Yes, just like I show in the video
@bebobalaquer83938 жыл бұрын
es lo mismo con un tercel del 95 ?
@InitechAuto8 жыл бұрын
Si
@bebobalaquer83938 жыл бұрын
+Carlos Cuadra gracias hermano deja ver como me va .lol
@sonofthedeathsergio7 жыл бұрын
donde puedo conseguir el diagrama de las mangueras de vacio?
crees que si están mal conectadas pueda ser este el problema de que tiemble el motor?
@InitechAuto7 жыл бұрын
A vacuum leak can cause rough idle. yes
@chuckles470s96 жыл бұрын
Will the head /valves be damaged if the belt breaks?
@claw-machinesNL6 жыл бұрын
if it's an non interference engine it won't (5e-fe is an non interference engine) depends on which engine you have (most older toyota engines are non interference)
@chuckles470s96 жыл бұрын
Thx for responding. I have the 5E FE engine. I picked up a Tercel with a rough idol and trouble shooting it.
@claw-machinesNL6 жыл бұрын
chuckles470 S what year is it from? I have a 1996 paseo/cynos with a 5efe engine, what did you try already to make it idle better maybe i can help?
@chuckles470s96 жыл бұрын
It's a 1995 Tercel AC,PB,AT 220,000 miles.When it warms up the idol gets rough. I've cleaned the throttle body, new spark plugs and replaced the radiator.Replaced the water temp sensor. The car will shake at times especially when sitting and steering the wheel. The brakes are spongy. Under acceleration it runs perfect.no check engine light on.Thanks for the help. Any thoughts are appreciated. I'm thinking about cleaning the throttle body again. It was extremely dirty.
@claw-machinesNL6 жыл бұрын
did you search for a vacuum leak? spongy brakes sound like the brake booster doesn't get vacuum and this could also declare why the idle is bad since that partially depends on vacuum. also make sure to check and have an air filter installed and maybe check the egr valve (if your engine have one)
@josetorres44007 жыл бұрын
ese motor es el mismo motor 2-e
@carloshuamani20935 жыл бұрын
por favor para fifundir un video automotriz debes estar con la ropa indicada ya que es un mal ejemplo para los estudiantes de mecanica automotriz
@InitechAuto5 жыл бұрын
Gracias por el consejo. En el futuro tomaremos en cuenta la ropa indicada.
@carlosbg04127 жыл бұрын
xq no es en español 😭😭
@pulquedelmejor8 жыл бұрын
7:26
@fowlercdff11 ай бұрын
Really? Shorts and flippy flops?
@InitechAuto11 ай бұрын
Gotta love summertime!
@pulquedelmejor8 жыл бұрын
I can't get past that pully
@InitechAuto8 жыл бұрын
+pulquedelmejor Are you talking about the crankshaft dampener? If you are, all you need is a puller.
@pulquedelmejor8 жыл бұрын
+pulquedelmejor we had a hard time installing the belt ,but we were able to fix by watching another video .