At first one would think it could be a more complicated situation but at the end it was an easy fix. Well done!
@mammamumrik3 жыл бұрын
There’s nothing important lacking in your English. You clearly communicate what’s important step-by-step, better than most. Many who want to show solutions do it from the “inside” and most of us who need help are on the inside: “My roborok is malfunctioning and I get no useful information from it. So when I saw the start of your video I realize you stand beside me where the trouble is, not far ahead where it’s already solved. -> a really good user interface . So I’m very thankful.
@TinC333 жыл бұрын
Thanks
@virgilcominca96702 жыл бұрын
just fixed mine! din't have to go into the orange motor. a small piece of rock was visible and i removed it. now it works. thank you!
@thyeboonbok28652 жыл бұрын
May'22 - Mi Vacuum Totally works for me! It seems complicated but it isn't. Mine was an easier fix. The band fell off and I just reattached it back to the wheel. Thank you from Singapore.
@davidmoore4875 Жыл бұрын
Thank you so much for this. I thought mine was ruined. I only needed to take the turret cover off (the second set of screws) to discover a long hair tangled up in the drive belt. I pulled it out and it's as good as new.
@jrprzybylowicz2 жыл бұрын
I had the same error with 5S Max. The only difference is the number of screws and slightly changed layout of those plastic casings. Your guide helped me out, thanks a lot, man!
@JcRabbit3 жыл бұрын
Thank you, tried this and it worked! Not as difficult as I thought it would be. :) In my case, unbeknownst to me, the cleaning lady had been mopping the robot as well as the floor - this of course meant some detergent ended up getting inside the LIDAR rotating mechanism and then dried up, preventing the orange plastic thingy from spinning freely.
@TinC333 жыл бұрын
always like to hear positive feedback, thanks, and great for you
@kennethlikens53962 жыл бұрын
I used a small vacuum around the top where the laser is housed. It worked. Try this first before getting your tools out but be careful.
@TinC332 жыл бұрын
Good idea, but i like to dig deep 😉
@alexanderfatikov854920 сағат бұрын
Thanks, man! That’s what I needed to fix my vacuum.
@TRHardware3 жыл бұрын
Got help with this video! Thank you very much! I had already swaped out the ladar unit, with error 1 at first place. Thought I have to spend another 100euros 2 year later... but this helped!
@volodymyrbatrukh42572 жыл бұрын
Thank you @TinC33! I was able to fix an error for mine roborock following the steps from the video. In my case there was a fingerprint on a laser and dust on a motor.
@przemysawromanczyk67003 жыл бұрын
Big thanks for this video. I opened, checked motor and cleaned all module and my roborock is working again.
@przemysawromanczyk67003 жыл бұрын
Unfortunately after two usages of robot it fails again with same problem. I opened it once again and used compressed air to do cleaning of sensor tower area. It's now working again. I spotted that when sensor is rotating it have some small inflexion maybe this is causing jamming of rotating parts. Do someone run for same problem?
@NikWeber.3 жыл бұрын
Awesome! First I thought, well that's too complicated for a quick fix but it was surprisingly easily. I not only repaired the S5max by removing something blocking the belt but I also feel more confident in tackling future technical problems. Thanks a lot! Your video saved me lots of money!! I subscribed and liked 🤗
@TinC333 жыл бұрын
Thanks, always like to hear that someone save $$$ with fixing something.
@eduardocarlos9467 Жыл бұрын
After a couple of attempts, got it working again. Thanks for the video. 👍🏼
@mturski19832 жыл бұрын
After watching this I first tried to just vacuum the tower itself with a handheld vacuum. It sucked out a tiny piece of styrofoam that got in there without any need for disassembly
@px432 жыл бұрын
Hey it worked :-D Turns out that when the roborock (S7) went under our Christmas tree, a pine needle fell into the lidar sensor and knocked the orange band off the wheel. Tweezered out the pine needle and put the band back on the wheel and we're good to go.
@Random-yk4wz2 жыл бұрын
very nice; I did not even havec to remove all the pieces - just the first one. Thanks for professional video!
@perastemark7943 жыл бұрын
Tack för videon, fungerade utmärkt!
@BijJoost3 жыл бұрын
Great video ! I fixed my problem within 5 minuts cause of it... Brothers of Domotica and enginering at top !
@jeremynino940 Жыл бұрын
Sweet! I ended up finding a tiny shard of glass! Thanks!!
@mauricekrijn5737 Жыл бұрын
Thank you! Great instruction video was able to fix mine easily! Indeed little stone caused the issue and now removed.
@cgttc043 жыл бұрын
You are the best! Fixed my roborock. Thank you.
@TinC333 жыл бұрын
Thanks
@gipielle5 ай бұрын
Hello, thanks for the video, i have a roborock s7 maxv ultra with error 1 but laser is ok (i have tried it on another robot), have you had any similar problem, I wanted to understand if there was some test I could do before replacing the motherboard.
@TinC335 ай бұрын
@@gipielle hmm idk but if you got a second robot i would try to replace part by part until find the problem 🤷♂️
@runningwithsavage Жыл бұрын
Great manual and it actually helped even though I couldnt find anything inside!but I just cleaned it a bit and it seemd to do the trick.
@runningwithsavage Жыл бұрын
sad thing though, after another 40 mins of work or so, the said error reappeared. Could it be the motor or something?
@buzzlightyear34613 жыл бұрын
Any idea wat specification or brand of Lidar module was used? Part # or manufacturer
@dutchbiker7874 Жыл бұрын
Really helpful! Thank you very much😊👍
@raisedfist892 жыл бұрын
In my case, it was a piece of Christmas tree getting stuck in there. Thanks for the video!
@kevinxchoi2 жыл бұрын
Thank you! Was able to fix following the steps!
@danijel1242 жыл бұрын
I bought one broken for cheap and repaired it ;)
@TheAquaClone3 жыл бұрын
Super video. Je ratalo, lep pozdrav :)
@TinC333 жыл бұрын
Super, najraje pa preberem komentarje, ko nekdo sporoči da mu je nekaj ratalo popravit z pomocjo videa.
@benjaminpollmann72003 жыл бұрын
Thx alot. Solved the problem on mine. There it was hair round the motoraxis.
@FedericoPasserini-x5d Жыл бұрын
you saved my day! TNX!
@chriswest837610 ай бұрын
Thank you for this. I always to hesitate to tear into a device for fear I do more damage than good. However, my device quit after circa 40 days since it was delivered to me and the manufacturer referred me to the seller who referred me back to the manufacturer. Grrrrrr. Basically, if I didn't fix it, the entire purchase price would be wasted. I have a Roborok 8+ but it is similar enough to the model you repaired to make the video useful. I found nothing more obstructive than a single pet hair but removing that and spraying a bit of contact cleaner strategically made the difference. Frankly, I think this design is far too fragile for a vacuum. Hopefully Roborok will take note.
@TinC3310 ай бұрын
Thanks, i'm the guy who can open anything if it's broken i can't make more broken 😁 Yestourday i replace iPhone camera, open them for the first time, everything work well... You just need to bealive into yourself, and take photos, notes... During disaasembely.
@comandante93123 жыл бұрын
Thank you i learned usefull knowledge. I changed lds motor 3 days ago. Now working well.
@GianFilippoFloriddia3 жыл бұрын
comandante, where can I get a lds motor? thanks!
@abccde38323 жыл бұрын
@@GianFilippoFloriddia Try ali express!
@GianFilippoFloriddia3 жыл бұрын
@@abccde3832 was an old message... I found the motor on Aliexpress. All good!
@spyderm4n3 жыл бұрын
Well made video! Thanks! My Xiaomi mijia 1s isn't following it's map anymore, making extra maps everywhere so I'm hoping it's just something with the lidar.
@TinC333 жыл бұрын
Hope, but it's smell by firmware failure, try to update firmware also.
@pyrhockz5 ай бұрын
Thank you just fixed mine !
@TinC335 ай бұрын
@@pyrhockz love to hear that 😀
@dimitrisz4562 жыл бұрын
what number of screwdriver i need for the screws in 1:59?
@TinC332 жыл бұрын
I think ph1 or ph2 will do the job
@johnnyj92282 жыл бұрын
Thanks! It helped a lot.
@mzmz93552 жыл бұрын
Thanks for the video. I've learned how to get to the laser sensor next time I'll be replacing the sensor - as cleaning & moving didn't help me. Firstly, the rotor moved (though slower than supposed to) but soon stopped, then the robot tried again with the same result and finished with 3rd attempt with error now even without sensor rotating. So, I guess I have to replace entire sensor.
@TinC332 жыл бұрын
If you remove the belt sensor rotate smoothly? Then try to jeplace only motor it cost just a few $ i read that some people got issue with motor.
@mzmz93552 жыл бұрын
@@TinC33 Yes, the rotor rotates smoothly (I've dissasembled the part with magnet to check it). So I ordered motor and let's see how it fares. Thanks for your advice.
@marinedebarre49353 жыл бұрын
Thanks! You help me a lot!
@maximumvideos2 жыл бұрын
Thanks, helped me fix mine!!
@GianFilippoFloriddia3 жыл бұрын
Hello TinC33, great content, thanks a lot! However I unmounted everything like you did, but nothing was inside to block the laser... I mounted back it worked for few seconds and it stopped again :-(
@TinC333 жыл бұрын
Make sure there is not something inside, try to unmound a bit furder, and check if the motor work without belt, you can power them with 5v (usb power) in any direction but disconnect it from the pcb firstly.
@GianFilippoFloriddia3 жыл бұрын
@@TinC33 unfortunately I didn't find the way how to test if the little motor, so I just order a new one on Aliexpress for just 6$... finger crossed! :-) Thanks for your great content and your kind answer!
@abccde38323 жыл бұрын
@@GianFilippoFloriddia Report back please how your story continuous @Gian Filippo Floriddia.
@GianFilippoFloriddia3 жыл бұрын
@@abccde3832 hello! Thanks for following up. After few days my little motor arrived directly from China, just 6$. Thanks your video I saved a very expensive fixing costs... I just changed the motor and now my Roborock works perfectly!!
@abccde38323 жыл бұрын
@@GianFilippoFloriddia You got S5? I'm noticing lots of spare part for former models, but few for latest (which makes sense)
@infoclub9876543213 жыл бұрын
Thank You, very good job.
@DDDeeccOOO Жыл бұрын
Thank you!
@malcolmtill3 жыл бұрын
I love your video's Thanks for sharing.
@TinC333 жыл бұрын
Thanks
@yountbo2 жыл бұрын
Thank you, had the same issue.
@alenabuchtova11983 жыл бұрын
thanks, it works now :)
@iaakki2 жыл бұрын
Wow! Had exactly the same rock inside the lidar. 😂
@JustKanji Жыл бұрын
Thanks that helped
@lostside3 жыл бұрын
What tool do you use to clean?
@TinC333 жыл бұрын
You mean rotary tool with steel brush in it, i use proxxon but also dremel would do the job.
@Rplus12 жыл бұрын
For some reason it did not work for me, I reached out to support and they said it could be the laser itself is broken. Do you know if they offer a replacement for the laser itself?
@TinC332 жыл бұрын
Try on ebay
@godopista3 жыл бұрын
very helpful for disassambly. There are cases however, where there is no mechanical block (laser head, belt, motor) and it is still not working. The motor works fine with 5V. I found somewhere a video where it was shown that driving the motor with 9V for a short time (few seconds) helps. So it was in my case.
@crazytime0013 жыл бұрын
Thanks it helped
@ikouv3 жыл бұрын
Great video, ive tried the steps and it works. Problem is that after a few cleanups the error repeats it self and I have to troubleshoot very often. Any idea what I might do?
@TinC333 жыл бұрын
Hmm it make me once and only never again, do you sure it's cleaned enough, so it turn unresistance, otherwise it may be weak motor new one cost a few $
@brucebonds6578 Жыл бұрын
mine top is over no screws cant remove lidar
@OsmosisHD10 ай бұрын
Just one thing I would have done differently. Disconnect the battery before doing this Would be a shame if you accidentally drop a screw on one of the the PCB's and cause a short
@TinC3310 ай бұрын
That's really good point, my bad, i also fix high voltage live manytimes, don't ask me how many times i feel instanr regreet 😅
@danielvelazquez99837 ай бұрын
Definitivamente yo le bajé... Cob smash me atasque de cómics, pase de 0 cómics a 400 en un par de años. Pero lo de panini es grosero... Ojalá bajen precios
@Benji2108 Жыл бұрын
Easy fix 😅
@nowymercedes3 жыл бұрын
The same error comes again after some time.
@TinC333 жыл бұрын
Than you may need new motor, check on ebay, ali...
@cdoubleu87193 жыл бұрын
@@TinC33 motor or lds?
@TinC333 жыл бұрын
@@cdoubleu8719 no no only motor, there are about 10$ on ebay, but you can try them before buying, unplug motor from the board and plug it to some usb cable 5v DC and you'll see if the motor stall or run ok.
@cdoubleu87193 жыл бұрын
@@TinC33 I have tried soldering the motor to usb. After 1 run I get error 1 again. Could it still be a faulty motor? Or is it really jamming do you think?
@TinC333 жыл бұрын
@@cdoubleu8719 i would say jamming, try to dissasemble more than i do you may find some dirt deaper.
@videomanx70543 жыл бұрын
no way in hell im doing that
@TinC333 жыл бұрын
It's easier than it look, plus feeling when fix with your own hand is amazing, but if you think you can't do that maybe better to give someone with a tool and knowledge.
@videomanx70543 жыл бұрын
@@TinC33 Going to give it a try myself, your right about doing it by hand.
@TinC333 жыл бұрын
@@videomanx7054 if not sure, take a photo before remove every part, so you can seen the position later when assembling together.
@videomanx70543 жыл бұрын
@@TinC33 Did it and it's working now! Thanks
@fm54012 жыл бұрын
Take 50$ And fix mine.
@TinC332 жыл бұрын
But you are on another side of the world i think 🤔
@2HellWUtube3 жыл бұрын
“Easy fix”…
@TinC333 жыл бұрын
Yea quite easy just need basic tool and about 10-15 minutes.
@steliosgk.75343 жыл бұрын
„Easy“ Fix. You kidding me?
@TinC333 жыл бұрын
Not that hard 😉
@steliosgk.75343 жыл бұрын
@@TinC33 I am not saying it’s hard to do. But you cannot describe it as easy. Easy fix would be to turn the robot upside down and shake it, or I don’t know reset it or something.
@marinedebarre49353 жыл бұрын
@@steliosgk.7534 don't watch if you are not satisfied
@steliosgk.75343 жыл бұрын
@@marinedebarre4935 and how will I know if I am satisfied or not if I don’t watch?
@10pmStalker3 жыл бұрын
@@steliosgk.7534 A screwdriver is involved. It's easy if you're not a moron.
@sutorcs2 жыл бұрын
Didn't even have to take the laser assembly apart. Just spun it and gave it a little shake while spinning it and eventually whatever was lodged inside just worked itself loose.