The toilet cistern kept filling with water. How to changed the ball cock washer/diaphragm.
Пікірлер: 103
@NGTV6004 ай бұрын
Had watched other videos which only explained in part, this video helped me finally solve my problem with water continuing to run and it was down to not lining up the marks when replacing the washer! Thanks so much! Saved me paying out ££££s for what was a simple fix!
@dennisbennett7064 Жыл бұрын
Thanks so much for this, I did exactly the same as you. I replaced the rubber fitted everything back together and yes it still leaked. There are 2 notches to align inner and outer. If you don’t get them both aligned properly then it will still leak. Thanks again.
@patrickgannon81907 ай бұрын
Thank you, that little tip to get the rubber aligned at the top has made all the difference, now at last the water has shut off....and for good as I was about to call out a plumber...!!
@MrRobimike4 ай бұрын
Great tip it would not stop filling for me until I saw this video and comment. Working perfectly now
@clairewheatley68275 ай бұрын
Mine was filling very very slowly I replaced the rubber seal and now it won't stop filling 😂 help! Fitted old one and was slowly filling so at least I knew it wasn't the actual whole unit. Finally after many attempts I got it to work!
@starmole50005 ай бұрын
I literally had this exact same problem only a few days ago. Had the diaphragm replaced and then it started overfilling. The issue for mine was the top bit. If you look at the bit where there's a small hole and what looks like a rubber flange, press your finger down on the plastic part in the center of the hole. If it stops overfilling then you have the same issue I did. I fixed it by placing 3 very small washers under the lip of the white hole so it held the flange and the little plastic bit down, essentially simulating constant pressure downwards, and it works now!
@davesutton238113 күн бұрын
I have exactly the same issue currently 🤣🤣
@KenR2084 ай бұрын
Good to see someone work on the inlet valve instead of the flush, and show us what happens when it's not fitted properly, most helpful,
@shelleyrichardson207016 сағат бұрын
Thankyou so much you are gold 😊
@shonaflaherty384 Жыл бұрын
thank you!!! from all of us too broke to afford a plumber
@tonykeary1270 Жыл бұрын
Perfect that little rubber thing was what was wrong with mine. Nearly fully degraded
@raghavendran71549 ай бұрын
This exactly worked for me. Saved my money. Thanks a lot for educating us sir
@nanumanu13Ай бұрын
The little nozzle was disconnected. Your video helped me find and fix it. Thanks a lot! 🤑
@Offline1988Ай бұрын
You saved my day, thank you so much! Basically the water tank was running constantly so I bought a spare part , when I got home I realised that was the wrong part, and was already Saturday, all shops are shut, on Sunday are not working, and the most issue is that I got one valve for both water tank and the bathroom sink, so shutting the water tank pipe valve would mean shutting the entire water in my bathroom. Found that the washer had some debris cleared it and it worked! Thank u so much sir! 🙏
@angelahart6218 Жыл бұрын
I replaced the rubber, its all in correctly and put it in and out multiple times now but its still overfkowing no matter how many times i take it out and adjust it. Losing the will to live!
@debnairwilson60523 ай бұрын
I'm off to B&Q with a spring in my step! Thank you for this!
@davemcdave216925 күн бұрын
Amazing big man. Thankyou. Short trip to screwfix and all sorted. You should set up 'buy me a coffee' as it's always good to give a small bit of cash for cracking advice.
@pdunleavy198224 күн бұрын
I’ll look into it. I think there’s a “Thanks” button on KZbin that lets you give tips. Somebody gave me one a few months ago. Glad the video helped.
@rhys194424 күн бұрын
Can anyone help please, the part that the button screws into has dropped further into the system and I can't see it, I need to replace it but don't know what it's called or where to find it
@cryptombt58804 ай бұрын
Thank you so much mate. This is the exact one I have. Time to order a new part
@CS-ms8pj7 ай бұрын
Thank you so much.I replaced the valve but now cistern is over filling. Think I need to adjust the float level but unsure how 😖
@pdunleavy19827 ай бұрын
Usually you can just twist the screw that the float is attached to.
@CS-ms8pj7 ай бұрын
@@pdunleavy1982Yes, I found ‘turn to left to left’ to lower water level but didn’t make any diff
@usy376 ай бұрын
thnx man its really help me 👍 i got this rubber cheaper 3£
@richardvannjones96327 ай бұрын
Thank you for taking the time to post this. It worked a charm! (after I managed to line up the valve notches properly. Glad I wasn't on hourly rates...)
@pdunleavy19827 ай бұрын
Glad it helped
@Cherub7710 ай бұрын
God bless you! Mine didn’t even need replacing just reseating in place
@mixaylo19819 ай бұрын
Thanks . I sort the problem 👍❤️❤️👌👌
@ellevee95234 күн бұрын
My toilet hasn't got one of those screws to turn the water off so i turned off the stopcock but the cistern won't stop filling up??
@pdunleavy19822 күн бұрын
@@ellevee9523 I’d say you haven’t turned the correct stopcock off then. Or it hadn’t closed all the way
@Gemrh86 Жыл бұрын
Hi, Thank you so much for this video. My cistern was taking ages to fill up. Just check and the washer was in a bad way. Just ordered another one. I have noticed as well that there was also a constant flow of water running into the bowl - would this be a related problem or it is something different? If so, what would be the solution? Would I have to change the rubber or a part at the bottom too?
@pdunleavy1982 Жыл бұрын
I think both problems should be solved with the new washer.
@Gemrh86 Жыл бұрын
Thank you so much for replying. Fingers crossed it does 🙂
@adamrandall6399 Жыл бұрын
Appreciate you for making this video. 🙏🏻
@stevengower99824 ай бұрын
What is the top bit of the filler value, the little white thing that drops into the hole when the toilet stops filling (see it drops at 7.51 in this vid). This is what won't drop properly on my toilet. Any idea how to fix? Is it another rubber seal or similar?
@jonos138 Жыл бұрын
I've had mine to bits the same. The rubber washer is fine and it still F**** leaks. Worst design ever for a cistern. I have 2 of these in my house and they are both shite. Both of them keep playing up and running water. Bring back the metal valves with plastic float. Rarely was there a problem with those. These crappy plastic fittings don't work 5 min without having to fiddle with them!
@davecustance34234 ай бұрын
Thanks for vid and thanks for leaving the section in that showed you had to try again … that helped me a lot because I had exactly the same problem and realised the washer wasn’t quite seated properly … well done v helpful … and also the toilet internal parts were identical … plus helpful Amazon link page cheers dave
@James-r8q2 ай бұрын
Absolute legend. £3.50 from my local helpful Plumbers' Merchant.
@James-r8q2 ай бұрын
Absolute legend. £3.50 from my local helpful Plumbers' Merchant.
@charlottethomas567710 ай бұрын
Doing mine. It's easier if you take the plastic arm away from the round plastic thread. When you go to put the thread back on you can align the notch perfectly and the plastic arm doesn't get in the way.
@wozzywaterfield591310 ай бұрын
I’ve changed the rubber but it’s still running after the cistern is full but it stops after about 30-40 seconds ? It does fill up fast now and not slow.
@clairemaule87475 ай бұрын
Thanks for this video, it's exactly what I needed to help me to stop my toilet cistern overfilling :)
@KieranJB4 ай бұрын
Did I skip ahead, miss the part where he turns the water pipe off, and spray water all over my bathroom? Maybe.
@pdunleavy19824 ай бұрын
I’m pretty sure that part was at the beginning.
@salfetka8 ай бұрын
I will have to try this i've got the same issue with the same toilet mechanism. Thanks mate
@marcjoyce7659 ай бұрын
Thank you, this was so helpful. I have 1 question though; i twisted the nob to make the float lower, however that doesnt seem to stop the water. It continues to fill the cistern until approx 5ml below the overflow pipe. Any tips or should i just apply the 'dont fix whats not broken' addage?
@pdunleavy19829 ай бұрын
I think I would leave alone. Or keep adjusting the float lower. Trial and error.
@CS-ms8pj7 ай бұрын
Please clarify what you did ‘wrong’ as I clearly have? I have done it twice now, taking care to match the notches & fail to see what the issue is why it won’t stop filling/shut off
@pdunleavy19827 ай бұрын
I didn’t line the notch up first time. When you pull it up with your finger, does it stop the water?
@michaeljawaharbravuri76659 ай бұрын
Thank you so much. Appreciate making this video. God bless you. I fixed mine with £3.5.
@redeyewolfman5 ай бұрын
Thanks you. Got this problem
@G4RY11595 ай бұрын
Always preferred a handle flush, they broke less
@RobertLupton-c4rАй бұрын
Legend
@megc182 ай бұрын
You any idea how yo remove that middle part? I've a problem I'm trying to fix and need to remove that flapper bit
@pdunleavy19822 ай бұрын
@@megc18 there usually 2 nuts underneath that bolt it to the bottom part of the toilet. Undo those and undo the water pipe and the top part should lift off. Then there’s a big plastic nut holding the middle part on. There might be some crews holding it to the wall as well.
@megc182 ай бұрын
@pdunleavy1982 I appreciate the reply mate. I can't do that though, I have alot of hidden things on the toilet. Cause it's fairly new most of the pipework ect is hidden. Can't even isolate the toilet. Need to turn off the water for the whole house when trying to sort it. Thanks though
@pdunleavy19822 ай бұрын
@@megc18 that’s the problem with hidden pipework
@megc182 ай бұрын
@pdunleavy1982 I'm sure I can get that flush valve out by unclipping it or something but I'm far too cautious I break it. Yeah the hidden features are a nightmare
@philtucker12242 ай бұрын
If you are talking about the central tower, it just turns slightly anti clockwise to un clip it from the base.
@darrenlee8118 Жыл бұрын
I changed my Diaphragm Washer but still finding the water still flowing slightly in the basin which makes the system every so often fill back up which makes a noise like there's a air block
@pdunleavy1982 Жыл бұрын
Have you double checked to make sure the diagram is sitting in there properly?
@olliemoffat40258 ай бұрын
Having this problem too. But the thing you unscrewed by hand on the left is tight and win't budge. Don't want to force it incase i break it. Any ideas? Please and thank you
@pdunleavy19828 ай бұрын
You might need a bit of help with a pair of grips. Just don’t go crazy. Can’t always be done by hand.
@CS-ms8pj7 ай бұрын
I had same prob, didn’t want to use metal on plastic. I gently tapped all around where I could & it unscrewed after a while
@peaksandpioneers-uv5nz11 ай бұрын
Hi there, we’ve got a similar cistern as in this video. The cylinder in the middle bit won’t slide down enough to close the gap and stop the water from running. Have you any tips on fixing this?
@philtucker12242 ай бұрын
That’s the problem I am currently having with my daughter’s cistern. (Did you eventually get it to seal?)
@KieranJB4 ай бұрын
Thanks
@pdunleavy19824 ай бұрын
Thank you very much. This is the first ever payment.
@KathleenRamsay-s4v Жыл бұрын
Hi, my toilet cistern was taking ages to fill up so I replaced the rubber seal as shown on this video. It worked great for about a week but now the water won’t stop running even when the cistern is full. I can’t get a plumber to come out to look at it. Do you have any ideas what it might be? Many thanks
@pdunleavy1982 Жыл бұрын
I would check the rubber again. Maybe it wasn’t sitting right and it’s worn a hole in it again.
@ilariafrau80184 ай бұрын
Thank you! You are a star ✨
@keithmonk45034 ай бұрын
Not mentioned in these videos is there is a rubber inset in the lever arm circa 6mm dia. Not easy to see as white the same as the lever. This can be indented to such an extent it cannot form an air tight seal to the little hole in the end of the plastic piece he took out. The rubber can be pushed out from the rear turned round and reinserted to expose a fresh smooth surface. I replaced the sealed in the video but still had a problem. Turned round the seal in the lever arm solved the problem.
@tonytraveller72184 ай бұрын
Im having the same problem, I do not see a rubber inset at all on the lever arm and cant find the part at all? I replaced the seal as in the vid (flow valve) but water is still jetting out of the little hole in the lever arm? And the toilet does not stop filling
Apparently part No 5 but where on earth do you get one of these?
@StevenGriffith-r4e Жыл бұрын
I have an identical toilet cistern to this and my problem is that the toilet won't refill after it's flushed. Do you have any suggestions please?
@pdunleavy1982 Жыл бұрын
Take the same thing apart that I did in the video. Check for any blockages.
@StevenGriffith-r4e Жыл бұрын
@@pdunleavy1982 Will do, thanks for the feedback 👍
@Dazlingmagic8 ай бұрын
Thank you!
@jedisct1 Жыл бұрын
What toilet flush mechanism is that? I have exactly the same and would like to replace it but I don't know what brand/model that is.
@pdunleavy1982 Жыл бұрын
I’m really not sure what brand it is. Take pictures and go to a local plumber merchant. Hopefully they will know.
@allansmith224811 ай бұрын
It’s a siamp they provide this mechanism to lots of toilet manufacturers
@mondaymya2611 ай бұрын
Excellent, problem solved!
@The-Salty-Bager8 ай бұрын
Do you know which make and model this toilet is ?
@pdunleavy19828 ай бұрын
I’ve got no idea.
@partiasharifi11 ай бұрын
Same problem here mate! Thanks a lot!
@martinshaw1610 Жыл бұрын
I just put a new rubber on but is now overflowing
@pdunleavy1982 Жыл бұрын
I’d try taking it apart and making sure the new rubber is sitting properly where it should be.
@astalavista_847 ай бұрын
Thanks - replaced the rubber seal already on mine but it wasn’t switching off the inflow when full, your video helped me fix it
@Discover-Ireland Жыл бұрын
Iv lost the plastic level lever do I need it at all
@pdunleavy1982 Жыл бұрын
If it’s the one that connects to the float, you definitely need it
@Discover-Ireland Жыл бұрын
@@pdunleavy1982 Thanks…ended up buying a new one to fit…after it was fitted I found the lever.
@peachesandcream875311 ай бұрын
Thank you!
@srosevear19886 ай бұрын
Camera person gave me motion sickness. Some advice, hold the camera steady and make slow, smooth movements.
@helengillett7054 Жыл бұрын
Hi, I've followed your video and it's almost perfect but there's now a slight trickle of water into the bowl, what am I doing wrong or is it another issue?
@pdunleavy1982 Жыл бұрын
Try checking that the new rubber is sitting exactly right. And make sure it’s the correct rubber.
@MrRapez Жыл бұрын
i have the same problem how do you know what size of the diaphragm of the rubber is
@pdunleavy1982 Жыл бұрын
I just took mine to the local plumber merchant when it was off.
@MrRapez Жыл бұрын
@@pdunleavy1982 ok thanks
@jacobjakub474 Жыл бұрын
You can get them in Screwfix mate i got two today For 12£