This video will show you how to change your Licence Plate (Number Plate) Bulb for your Audi or VW. Looking for tools? www.totaltechnik.com/selectstore Video by TOTAL TECHNIK
Пікірлер: 25
@louisgabrielle21542 жыл бұрын
I have a 2008 Audi A4 quattro convertible and I try to replace the whole license plate light plastic housing but when I unscrew it the plastic housing is stuck and don't come out even when I remove the screw. The right side plastic housing the screw is all the way in which I can't see it that well. What do you think I should do? Can I use WD40 to loosen the edges of the plastic license plate housing and try to get it out with a flat screw driver to pop it out? I'm changing both left and right plastic license plate housing with new Audi bulbs.
@jackcroft96547 ай бұрын
Top man
@dcartellone2659 Жыл бұрын
Is this the same process for a mk5 Jetta?
@louisgabrielle21542 жыл бұрын
Where can I get the this LED canbus bulbs for my 2008 Audi A4 quattro convertible license plate? Amazon? Do you have the name or link?
@abdulbeany1894Ай бұрын
Hi on the a4 b7 are both light holder interchangeable or are left and right different fitting thanks
@Myqueensandkings15811 ай бұрын
Anyway to remove a stripped screw?
@dcartellone2659 Жыл бұрын
Good information quick question does it matter which end you put it back for light lumens.
@williambritcliffe22112 жыл бұрын
Previous owner of my B6 snapped the heads off the screws I can tell you replacing the whole unit was not fun.
@perdanielsorensen77752 жыл бұрын
On one side on my A4 B6 Avant the screw was so rusted I had to drill it out. Bought stainless replacement screws from Ireland, because no shops here in Norway had them.
@DutchDukeMan2 жыл бұрын
most awkward possible angle and the most brittle little screws
@TotalTechnik2 жыл бұрын
Yes, the screws they use are TERRIBLE! Very weak. --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
@perdanielsorensen77752 жыл бұрын
I had to use a tiny ratchet wrench for 1/4" bits. None of my screwdrivers would reach it without being at such a bad angle that I couldn't get a grip on the screw.
@DanMevan2 жыл бұрын
Im about to change mine but ive noticed that the heads on my screws are almost stipped down completly, any tips to get them out?
@Frederic91fr2 жыл бұрын
Same here :s
@TotalTechnik2 жыл бұрын
Yes, they tend to do that and it's very annoying!! You'll need a screw extractor of some kind, and it could get messy! You need something that can grip into the head and get it to move, and of course new screws for when you do finally get them out. Best of luck, not a nice job! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
@perdanielsorensen77752 жыл бұрын
I had to drill one of the screws out. I used a dremel with a flexible shaft, a 3mm drill bit and lots of patience.
@156nunez2 жыл бұрын
Mine's do not come on at all,any idea what might be the cost, checked everything else
@TotalTechnik2 жыл бұрын
Assuming that the bulbs are definitely ok (?), and that they'll only come on when the headlights are on, and and you've checked the fuses for possible issues there, then the next stage would be to check the power going to the bulb inside the housing, with a multimeter. To see if the 12v feed is coming through to the bulb. After that it's going to be more complex by starting to trace and test the wiring. Best of luck! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
@perdanielsorensen77752 жыл бұрын
I just had a MOT failure on one of these bulbs. It turned out that the bulb was ok, and the wiring supplied 12V, but the connection between the metal on the bulb holder and the metal inside the boot lid was faulty. I bent the metal on the bulb holder slightly. That fixed the problem.
@qrew Жыл бұрын
mine wont fit
@billywhizz982 жыл бұрын
Good video but would have been better to have seen them working
@SelyoDz Жыл бұрын
don't forget to test !
@andrewhale37712 жыл бұрын
If you are changing them for LED's you will need to change BOTH, otherwise the Police stop you every 5 bloody minutes when they're bored!!!
@TotalTechnik2 жыл бұрын
Yes, nice tip, lol!! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!