How to Replace Wheel Bearing 2008-2012 Honda Accord

Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ia/1AAX...
New Wheel Bearing Set from 1AAuto.com 1aau.to/ia/1ASH...
This video shows you how to install a wheel bearing on your 2008-2012 Honda Accord. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This repair was done on a 2010 Honda Accord LX-S 2.4L Coupe 2-Door FWD Manual and the process should be similar on the following vehicles:
2008 Honda Accord
2009 Honda Accord
2010 Honda Accord
2011 Honda Accord
2012 Honda Accord
Tools you will need:
• Impact Screwdriver 1aau.to/oV/1AXA...
• Phillips Head Screwdriver 1aau.to/oDS/1AX...
• Pry Bar 1aau.to/oie/1AX...
• 10mm Socket 1aau.to/ozn/1AX...
• 12mm Socket 1aau.to/oDP/1AX...
• 17mm Socket 1aau.to/oDP/1AX...
• 19mm Socket
• 36mm Socket 1aau.to/oD/1AAS...
• Ball Joint Press
• Brake Caliper Compressor Tool. Quad Piston. Ratchet Style. 1aau.to/op/1AXA...
• Brake Caliper Hanger 1aau.to/obv/1AX...
• Hub Puller
• Pliers
• Side Cutters
• Snap Ring Pliers
• 1/4 Inch Ratchet 1aau.to/ozn/1AX...
• 3/8 Inch Drive Ratchet 1aau.to/oDP/1AX...
• Torque Wrench 1aau.to/otd/1AX...
• Gloves 1aau.to/oei/1AX...
• Rust Penetrant
• Safety Glasses
• Chisel 1aau.to/obV/1AX...
• Hammer
• Pick 1aau.to/ogy/1AX...
Subscribe: / @trq
Check out our playlist:
Honda Accord 2008-12 8th Gen: • Honda Accord 2008-12 8...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@doug743]

homie busted the new bearing and just slapped a new assembly on like no one would notice

[@SrColon309]

🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

[@brianlee677]

Great video it seems much easier to just buy the assembly with bearing already installed.

[@J_3564]

Is it possible to just buy a knuckle and bearing/hub assembly already put together? It seems like that would be a lot easier

[@Joel-bg3cf]

Seems easier to just replace the whole knuckle!

[@ramonmoreno5487]

It is. But replacing the bearing alone is cheaper.

[@brianflores4225]

When you pressed the hub , it didn't blow out the bearing?

[@hhn2002]

you guys are life savers! thank you!!!

[@TRQ]

+@hhn2002 Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@SrColon309]

Excellent work my friend. Thank you so much.

[@rony23ify]

Hello, thank you fur video wonderful video. where can I buy the hub puller tool that you are using? Thank you kindly

[@williamsegalla3693]

What is the part called for the trim ring… I just pulled two front assemblies off and the trim ring is missing on one of them😮

[@compilecodebug6430]

Was that axle nut staked? If it was did you pry it up beforehand?

[@diulaylomochohai]

Whats the oemtool you used to get the bearing out? Whats the tool#?

[@jenniferschultz4418]

How long does this take ?

[@westcoast8185]

What tool was that at 12:33 ?

[@brimlea]

22.50 did it not occur to you that something is wrong here😒

[@christopher4692]

Worst part about this video is you don’t show which exact adapters you use to take out the bearing smh

[@ericm302]

I do these and never take out that ring. Ever

[@brimlea]

29.50 this is not how you do it as you risk snapping the bleeder screw off. Oh you did people like you should not make vids if you don't know the basics of engineering

[@mast0rs]

Left out an important step removing Philips head screws from rotor

[@bill2461]

This video was s waste of time, had I known you need a hydraulic press , I wouldn't have watched it! How many DIY people have a press?