THANK YOU SOOOOOO MUCH for that mounting tip ! just struggled for 2 hours before remembering you mentioned this . came back and boom!
@jonmaloneycycling75932 жыл бұрын
You're welcome!
@karsten46892 жыл бұрын
Great video! I rode tubeless for 2 years (Conti 5000 TL 32 mm, Schwalbe sealant). Great rolling, comfort and weight. But a pain in the ass if it comes to mounting, maintenance (incl. slow air loss), tyre change, mess with the sealant. I finally went back to a tube setup: Conti 5000 32 mm, Schwalbe Aerothan tubes (which are amazingly light). Same low air pressure comfort, lighter in total, no air loss and so much easier to handle. Back for good 😀
@jonmaloneycycling75932 жыл бұрын
Nice!! and thank you
@discbrakefan2 жыл бұрын
I find tubeless lose air a lot slower due to the sealant and lower pressures. The right tyres and rims make a huge difference.
@2715jedi2 жыл бұрын
Great video!!! Video on fixing a flat on the side of the road? Going from that tubeless set up to putting the tube in and the steps it takes. You just explain things step by step thats easy to understand and grasp.
@jonmaloneycycling75932 жыл бұрын
thank you!!
@TexasWahoo_2 жыл бұрын
I resisted tubeless for a long time but I loved it once I tried it. It's less hassle than I expected. And when I changed tires it was cool to see the punctures I never even know I had. I think your simple, straightforward video can take the fear out of it for people interested in making the switch.
@jonmaloneycycling75932 жыл бұрын
Nice! thanks for sharing
@romanarem2 жыл бұрын
Never going back to tubes. Good vid
@jonmaloneycycling75932 жыл бұрын
thank you
@Chris-wf4ws2 жыл бұрын
Stan’s race sealent,genius choice. The best one I’ve ever used.
@jonmaloneycycling75932 жыл бұрын
Nice!!
@chiefrocker122 жыл бұрын
Agree on your comments on sealant issues/messy-ness. Was on road bikes tubeless for more than 3 years and unfortunately did get caught out a few times. Switched back to latex inners and tubolito as rescue tubes. Less stress as I know the worst possible scenario. Gravel bikes are still on tubeless, larger tires tends to work better. None the less, good tips Jon.
@jonmaloneycycling75932 жыл бұрын
thank you!
@simonlockwood8720 Жыл бұрын
Thanks for the great vid. In my experience tubeless is more hassle, but because the hassle is at home rather than the side of the road, im cool with that. I have put a tube in on the side of the road when i hit a huge pothole. Poured the sealant away. You get your hands dirty with tube changing anyway, so the small sealant mess didn't phase me. For me it was just the same process as changing a tube. Another reason not to use CO2 is that it can freeze the sealant in the valve and actually break the valve. I've seen that happen.
@marcusvaldes Жыл бұрын
Really enjoy your channel. I rode a lot in my 20s, stopped and developed Type 2 Diabetes. Back for good now and enjoy learning about the new tech from you. You have a good way or presenting it. Flash pump is on the shopping list. Never even heard of one before!
@charlesmansplaining2 жыл бұрын
Yup, the sealant is too much mess for me to deal with anymore. Rarely does it seal a puncture in the dozen or more times I've had them on the road which leaves me putting in a tube anyway. There is no weight saving benefit because 60ml of sealant equals about the same amount in grams 60g which is what a latex tube weighs and tubeless specific tires weigh more than a normal clincher. So if you're a weight wennie you might as well go for the tubes. I can change a tube in a couple of minutes which doesn't pose a problem either. If I was going to race I might opt for a tubeless wheel but training, never, I'll stop and change the tube mess free.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing, appreciate it
@jreitsma2 жыл бұрын
I had the same issue. However, I've found that the right sealant makes all the difference in the world. Stans Race has sealed every puncture I've had over the past two years.
@bradsanders69542 жыл бұрын
On my roadbike, I run orange seal in the tubes.......or did for 4 years with great luck............now Ive got some 32mm semi slicks from panaracer and those I run tubeless....................better carry everything needed if it goes bad. And be able to get that tight tubeless tire off and on the rim to put a tube in...................Orange Seal works really well for me.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing!!
@imperceptible21082 жыл бұрын
Nice! I think the few times you have to deal with the mess of the sealant is worth, not having as much punctures, as a regular setup. Also, i use tubeless, and won't go back to tubes, as i find it more convinient and as you said, you can run low tyre pressure. I have had a puncture that the sealant did not seal, and i wasted a lot of time, waiting by the side of the road, for the sealant to do its job. Lesson learnt. I now have the Stans Dart and plugs on my tool kit. However, i still carry a Tube and would evaluate the size of the puncture and make a decision on whether i use those, or just stick a tube in (which may be quicker) and not waste too much time. A track pump works fine for me, at home. Thanks for the video
@jonmaloneycycling75932 жыл бұрын
thank you for sharing, really appreciate it
@Wyzbowski2 жыл бұрын
I'm rocking tubeless on my MTB and Gravel bikes but still haven't tried it on the road bike. I'm totally with you on your 2 for 1 replacement MO and I too never bother seating before filling with sealent. When my current tires get replaced I think I will finally try tubeless on the road bike.
@jonmaloneycycling75932 жыл бұрын
Right on!
@michaelglidewell15242 жыл бұрын
Running tubeless on my road bike for several years now and I would never go back. Yeah sure every once and a while you get sealant on your frame, but most of the time I notice it when I'm cleaning the bike NOT when I'm riding. So that's just another time I would have had to change a tube if I wasn't running tubeless.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing!!
@evallari12 жыл бұрын
At the end, more pro than coun to use tubeless, what about of advantage of low psi if we compare with standard tire?
@bubby3722 жыл бұрын
Another informative video Jon. I agree with others here.Tubeless is such a mess and expense. Tubolito S-Road tubes for me. Lighter than tubeless any day and super easy to carry a couple of spares.
@jonmaloneycycling75932 жыл бұрын
thanks for tuning in
@nclsv2 жыл бұрын
Interesting technique for putting on the second bead! Definitely gonna have to try this !!
@jonmaloneycycling75932 жыл бұрын
thank you!!
@salsalawyer2 жыл бұрын
I use Orange Seal, a flash pump and add an Ounce through the stem every other month or so. I replace or clean out the stems about three or four months. No issues. great video as usual.
@jonmaloneycycling75932 жыл бұрын
Nice!! and thank you
@kevina78282 жыл бұрын
Stan's race sealant advises against injecting it through the valve, but adding before installing the second bead gets messy.... Ever had an issue injecting through the valve? Great channel and content.
@jonmaloneycycling75932 жыл бұрын
thanks so much!!
@ronnychan80032 жыл бұрын
I am wondering about the same thing. Just started to go tubeless and I am constantly thinking how am I going to refill the sealant! Although I like race sealant, I wld hate to unseat the tyre every time… so an injector works, it wld be great!
@randolphmulder80512 жыл бұрын
Yeah I used injector on mine but found that it did not inject all the fine particles in the race sealant and without those particles it does not seal as well as it should. It will be great if Stans made a injection specific to their race sealant. Great video Jon
@Michaelholds77692 жыл бұрын
Pretty sure they don’t recommend injecting through valve stem with a valve core installed. If you remove the core, it shouldn’t be a problem.
@damo52192 жыл бұрын
Great video Jon. I like the reliability of tubeless, however my rims are currently in the shed, waiting for me to waste another half a day to clear out dry sealant, and rim tape residue. The dried sealant prevents the tyres seating. I'm almost at the point of buying an air compressor to get the tyres to seat.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing!!
@bradsanders69542 жыл бұрын
The bummer is when the seal quits between rim and tire.............maybe 1500 miles into a tire running tubeless on gravel bike it lost the seal. Complete bummer out in the field..........tubeless takes work,and technique,and attention needs to be paid............its not a magic fix..............I can swap a tube out in no time on roadbike, as opposed to things that can crop up with tubeless.
@AOL03212 жыл бұрын
Great idea about changing the front after changing the second rear tire
@jonmaloneycycling75932 жыл бұрын
thanks
@MrJwmurph2 жыл бұрын
I mostly use Stan's Sealant (for conti and pirelli tires), not the race one as they say the race version cloggs the valve core when injecting it in through the presta valve. I've also got a set of Vittoria Corsa tubeless tires and they recommend Muc-Off sealant, it's much thicker when it's in the tire, doesn't slosh around but coats the inside and sticks to the tire. I haven't had an issue with either sealant. With the Vittoria and Muc-Off I rode the bike immediately after the install, came down off a footpath outside my house and the tire "burped" and resealed immediately. I guess the bead wasn't perfectly seated but popped on after the burp, if the sealant had glued the tire to the rim after a period of time it may not have popped into place and could have been a safety concern.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing, appreciate it bro!!
@NeutralGenericUser2 жыл бұрын
You make this look SO EASY, but it's actually insanely difficult. I've tried so hard to get those damn GP5ks on my wheels, and seeing all the videos on yt, thought I must be doing something wrong. Then I watched 2 bike shops struggle with it and realized that they really are hard af. You're experienced and know what you're doing. I wish I had your skills 🥲
@michaelglidewell15242 жыл бұрын
It's all a matter of what tires and wheels you have. Get the right set of tires on the right set of wheels and it can be fairly easy. Wrong wheels and tire combination and it can be a royal pain in the rear.
@jonmaloneycycling75932 жыл бұрын
You'll get the hang of it!
@richardggeorge2 жыл бұрын
Try to push the beads into the centre channel of the rim which effectively makes the rim smaller
@eriks.97302 жыл бұрын
I would love to run a lower PSI. Currently run 70 front and rear. Rarely get flats with Contis or Vittorias and latex tubes. When I do get a flat it’s usually time to replace the tire. Reluctant to switch to tubeless because I’ve lost hand strength and can’t budge the bead.
@jonmaloneycycling75932 жыл бұрын
Nice!!
@kennyc21242 жыл бұрын
Hi Jon there is an easier and cheaper way of pumping up the tire for the bead to settle. Just make sure both sides of the beads are push in to the middle canal especially around the tubeless valve area. And you can use basic pump to pump it up. Try it.
@jonmaloneycycling75932 жыл бұрын
thanks for the suggestion!
@marcusvaldes Жыл бұрын
Yeah. but that flash pump is so freaking cool!
@user-tq7gz2sf9u2 жыл бұрын
Great video Jon.Thank you.
@jonmaloneycycling75932 жыл бұрын
thanks for tuning in!
@lifestyleinc0233342 жыл бұрын
Thank you for an Inform video John. I’ll stick with the old school tube
@jonmaloneycycling75932 жыл бұрын
thanks for tuning in
@bennop.25532 жыл бұрын
Will be an interesting video to set up tubeless ENVE SES Road TLR Tyres🙂
@jonmaloneycycling75932 жыл бұрын
yes!!
@tolulopeobe2 жыл бұрын
Having fine through 3 pairs of conti GP 5000 over the last 2 years, I can say you don’t “have to have” a flash pump. I’ve seated my tires with regular DV track pumps
@jonmaloneycycling75932 жыл бұрын
Nice!! thanks for sharing
@bikepackingadventure79132 жыл бұрын
Can I recommend a new product called the ‘tyre glider’ instead of a normal tyre lever. I was sceptical but thought I would get one. I’m converted , makes getting tough tyres on and off so much easier. I’ve used it on my tubeless tyres and the tyre glider made it much easier to get the right tyres back on
@jonmaloneycycling75932 жыл бұрын
thanks for sharing!! will check it out
@waynosfotos2 жыл бұрын
Man I run Tubulars, and people believe they are a lot of Faff. Watching this, tubulars are easy, and the bonus is you can run sealant in them just the same. If the sealant doesn’t work, you change the whole tyre, no mess everywhere. I think cycling is becoming more complicated to make it “easy”. Those old systems worked fine AND tubulars can be run at lower pressures than tubeless. Until they make Tubeless set and forget, they will not be there yet. I haven’t tried the new Vittoria insert for tubeless that was used in the Paris-Roubaix, but this maybe a better solution.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing!! appreciate it
@richardggeorge2 жыл бұрын
1. FYI, you can use tyre plug to fix big leaks (when sealant doesn't do its job) - I use a compact plug kit called "Maxalami Tubeless Repair Kit" but there are many different types that work. 2. I ride tyres until the stitching comes through (ignore wear indicators). You don't have to replace it.....just ride it on the rear just in case it lets go. 😁
@jonmaloneycycling75932 жыл бұрын
thanks for the feedback!!
@kidsafe Жыл бұрын
DynaPlugs are vastly superior to worms/bacon-strips for road pressures. My DynaPlugs hood at a tested 100psi whereas something like a “Maxalami” strip can shoot out,
@0xjdion2 жыл бұрын
Hey bro, I’m impressed how is easy for you to put the tire back on the wheel. I would love to see a video on cable maintenance. Thanks
@jonmaloneycycling75932 жыл бұрын
thanks!! and will do
@briandowling94462 жыл бұрын
You ever hit Phoenix West Valley for a ride! Check out WVC in Goodyear! Most pleasant fast ride!
@jonmaloneycycling75932 жыл бұрын
thanks for the recommendation!
@peteturner84932 жыл бұрын
If you push the new tyre to the centre part of the wheel rim you'll find you can get it off or back on very easily minimal use of the tyre lever is required, why because the centre part of the wheel rim gives the tyre the most amount of space on it's circumferance.
@jonmaloneycycling75932 жыл бұрын
thanks
@DanTuber2 жыл бұрын
I've never had a flat in 4 years of riding. Just use butyl tubes and conti tyres. Maybe i'm lucky.
@stephenducey21622 жыл бұрын
I actually hate you...sincerely, Averaging 0.3 Flats a Ride
@jonmaloneycycling75932 жыл бұрын
Nice!
@joelberman59812 жыл бұрын
Oh now you’re in trouble. You’re tempting fate. I wonder how many flats you’ll get in the next month?
@jonmaloneycycling75932 жыл бұрын
@@joelberman5981 Lol
@kevinw70442 жыл бұрын
Tubeless is only messy if you spill the gunk. In all honesty, it’s simple to install tubeless tyres and keep all the gunk in the tyre where it should be. Doing things like pumping up tyre for the first time with gunk in the tyre is a bit silly. A recipe for creating a mess if the tyre does not seat first time. Always pressure the tyre without gunk first to seat it. If it seats, use your syringe to pump the gunk through the valve with core removed. Then inflate the tyre again. Never had a tubeless puncture that has not sealed but I do carry a spare tube. Like most KZbin videos your video misses techniques that can help a more stubborn tubeless installation. But it is a simple process even with a more awkward install.
@jonmaloneycycling75932 жыл бұрын
thanks for the comment, appreciate it!
@pneumadeux2 жыл бұрын
I'm in the process of building up a new race bike, and tubeless has been a big hangup for me. I've been thinking of keeping up with the new kids, but... Why? I run latex tubes, ultra light Vittoria Corsa tires or Conti 5000S IIs, and I've not had a puncture in y e a r s despite living in the industrial US midwest. And I ride thousands of miles a year. Why? Mr. Tuffy tire liners. The super skinny orange ones are light, easy to install, and well, they just flipping work. I still get the suppleness of great tires and crazy light latex tubes without the wet sticky hassle. The only time I can remember a flat was a truly bizarre situation maybe 5 years ago(!) where I had a small rip in the sidewall. I doubt sealant would have helped on that one.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing, appreciate it
@roxic12122 жыл бұрын
Great, honest video, thanks.
@jonmaloneycycling75932 жыл бұрын
thank you!!
@tunguyenminh97552 жыл бұрын
I'm always thinking about if I go for tubeless then my wheels hit a sharp metal, the sealant definitely won't seal the hole. No way to fix that hole on the road but replace the broken tire. That will be the disaster if you're far from civilian area. No one cary tubeless stuffs to fix that when riding. In my opinion, tubeless only helpful for pro riders who have many supporters for the strips.
@jonmaloneycycling75932 жыл бұрын
thanks for the comment
@mancello2 жыл бұрын
You can spray some warm soapy water on the tire sidewalls and bead to help seat the tire on the rim prior to inflation.
@jonmaloneycycling75932 жыл бұрын
thanks for the suggestion!
@MJarthur952 жыл бұрын
It’s way too much pfaff with the sealant, etc. I run my GP5000 with latex tubes, best of both worlds. Just pump up my tyres before every ride no issues 👌🏽 When my rear tyre is worn, I swap my front to the rear and put a new one at the front, but since I run 25mm at the front and 28mm at the rear this isn’t possible anymore.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing!! appreciate it
@mrwezbo2 жыл бұрын
Biggest thing for me is the comfort. I can run way less PSI than compared to tubes. I disagree with your thing about 'just put sealant in first' -> If you have had to put a tube in on the side of the road, your rim tape is toast. You need new rim tape. I find any tubeless issues come from dodgy rim tape, which if you put sealant in first isn't going to fix anything, you're just going to waste sealant. So bead the tyre first, let it sit for like an hour. If it holds air, you know your rim tape is fine. If it blows air straight away, you know your rim tape isn't good.
@jonmaloneycycling75932 жыл бұрын
thanks for the comment, appreciate it
@haoma44712 жыл бұрын
nice video !really enjoy it! thx!
@jonmaloneycycling75932 жыл бұрын
thanks! glad you enjoyed
@matthewk32332 жыл бұрын
The old conti 5k TL tires were a bugger to get on for me, I ended up just using vicegrips to hold the one side of the tire lol Maybe not ideal.
@jonmaloneycycling75932 жыл бұрын
Nice!
@MrMars1212 жыл бұрын
One way to reduce sealant messiness is to have the valve at any position except 6 o'clock. That way sealant won't spill out. In the video you pumped at 6 o'clock, which can cause sealant to spill out when you pull the hose out, because gravity pulls it down to 6 o'clock position.
@jonmaloneycycling75932 жыл бұрын
thank you for sharing! appreciate it
@tamerzeybek2 жыл бұрын
we have the same set of wheels and bike. How many mm rim strips should I use to make it tubeless? Are the bearings of the rsl 37 sets ceramic? Thanks for your useful sharing.
@jonmaloneycycling75932 жыл бұрын
Thanks man, I don’t think they are ceramic. I used 23mm tape
@solitaryrefinement67872 жыл бұрын
At my weight, the only rideable drop is 10 PSI which isn't much of a difference and being able to ride longer with a compromise tire is not very confidence inspiring to me personally. Since I'm not racing, rolling resistance isn't a priority as much either. I'll stick with easy to repair tubed tires on New York State roads that really shred tires. BTW, great tutorial and insight on mounting tubeless tires. 👍
@jonmaloneycycling75932 жыл бұрын
thanks for sharing and the kind words!!
@mynock2502 жыл бұрын
Specialized Sworks has stopped specing tubless tires wheels for its newest bikes since 2020. The reason, makes no sense slower, heavier tested many times. On MTb makes tons of sense, on road not so much.
@jonmaloneycycling75932 жыл бұрын
thanks for the comment!
@wynchesster2 жыл бұрын
What brand of tubeless tires are you using? I use YKSION PRO UST 2 tires 28mm, I run Mavic SYS SLR wheelset, which are UST, so super easy to setup. Only issue, is finding the tires for the bike. I had to buy my latest set of tires of Ebay from a guy in Bulgaria because I couldn't find them in stock anywhere. But I LOVE running tubeless, been tubeless for about 15 years on my mountain bike, and only the last 2 years on my road bike once I got my new wheelset. I'll never go back to tubes. Haven't had a single flat on my road bike since I put them on.
@jonmaloneycycling75932 жыл бұрын
I really like shawble and connti but yes stuff is very hard to find
@ShelterG2 жыл бұрын
Great video.
@jonmaloneycycling75932 жыл бұрын
thank you!!
@ckys41152 жыл бұрын
Thanks!!
@jonmaloneycycling75932 жыл бұрын
thanks for tuning in!
@javil18032 жыл бұрын
Question? How do you clean your disk breaks? Do you use any special product. Thank you. Keep up the good work 😁
@jonmaloneycycling75932 жыл бұрын
I just use rubbing alcohol
@rdkuless Жыл бұрын
Jon, there is another option you didn't talk about.. What are your thoughts on the SLIME..? or the inner tubes with SLIME already in them..?
@utah1man2 жыл бұрын
Tubeless is great! But when it gets bad, it's gets ugly quick.
@jonmaloneycycling75932 жыл бұрын
true!
@nhatminhphanvo52252 жыл бұрын
But what if i have problem on there road how can i carry me flash pumcher ?
@jonmaloneycycling75932 жыл бұрын
Check out my latest video
@pimbeweegt2 жыл бұрын
A good Floor pump should be enough. More important in my opinion is the compatability of the tire and rim.
@jonmaloneycycling75932 жыл бұрын
good point
@jreitsma2 жыл бұрын
I use a floor pump for mine too. General rule of thumb is, if you're having trouble seating the bead, add one layer of rim tape. If that doesn't work wrap a thin load strap around the wheel to push the tire against the rim (and hold it tight with your left hand, don't use the ratchet). As the you inflate the tire (using your right hand) gently let go of the load strap.
@jonmaloneycycling75932 жыл бұрын
@@jreitsma Nice!!
@AOL03212 жыл бұрын
Are they really needed for the road if you’re not a heavy rider? Of course for Mtn biking you’d be crazy to go without tubeless.
@jonmaloneycycling75932 жыл бұрын
Good question
@ibani64982 жыл бұрын
Hi Jon, what about products like dynaplug to fix punctures with road tubeless…. Have you ever tested it?
@jonmaloneycycling75932 жыл бұрын
I have tried them but didn;’t have much luck
@nathansdad042 жыл бұрын
Flash pump too much of a PITA imo. I bought a small pancake compressor. Makes seating tires a breeze…and obv can be used for a bunch of other stuff around the house
@jonmaloneycycling75932 жыл бұрын
thanks for the comment
@lance35912 жыл бұрын
Tubeless is 100% better than tubes. I don’t ever carry a spare tube or CO2 anymore. Even on long 100 mile rides. Sure the sealant is a pain once in while but I’d rather mess with sealant than buy tubes. When I find sealant on my frame I’m like yes! Saved another 15 to 20 bucks by NOT running a tube. It’s not that hard to run tubeless, takes a little bit of work. The pay off is way worth it IMO.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing, appreciate it
@Nick_007ia2 жыл бұрын
👍🏻
@jonmaloneycycling75932 жыл бұрын
thank you!!
@psps45502 жыл бұрын
Try tubeless before, not every wheels are 100% compatible, I prefer and I m using latex to get get better feel on the road
@jonmaloneycycling75932 жыл бұрын
thanks for the comment!
@davidknights9062 жыл бұрын
perfect timing Jon I've just switched to tubeless using the silca ultimate sealant, the only problem I have encountered is that I struggle to remove the tire due to arthritis in my hands, is there a trick to removing the tire?.
@jonmaloneycycling75932 жыл бұрын
Thanks man, no it’s a bear for sure. Good tire levers like those red Bontrager ones I use really help
@wrightwoodwork2 жыл бұрын
Don't need tyre levers. Make sure tyre is in the well and should be able to do by hand
@jonmaloneycycling75932 жыл бұрын
thanks for the comment
@ryandawson58002 жыл бұрын
Your veins are popping! Do you lift as well?
@stephenducey21622 жыл бұрын
I've always wondered this...you natty bro?
@thatguy90512 жыл бұрын
I think most of us can guess...
@timothymburton2 жыл бұрын
Jon used to be a competitive body builder.
@jonmaloneycycling75932 жыл бұрын
I used to workout a lot!
@thatguy90512 жыл бұрын
@@jonmaloneycycling7593 Found the family / exercise balance 95% of us haven't....Props to you sir.
@desertratsummers2 жыл бұрын
Did they get rid of the TL lineup? I do see the TR but currently run the TL in a 28 and really love them
@jonmaloneycycling75932 жыл бұрын
I think they still have them. They are great tires
@BananaChipzzz2 жыл бұрын
You're not supposed to put Stan's Race sealant through the valve stem. In the tire only. Direct from Stans: "The quantity and size of crystals in this special formula means that Stan's Race Sealant can only be installed directly into the tire. As a result of its immense sealing capabilities, Race Sealant is not compatible with injector or other valve installation methods. "
@jonmaloneycycling75932 жыл бұрын
thanks for the comment
@BananaChipzzz2 жыл бұрын
@@jonmaloneycycling7593 anytime brother. Thanks for all your videos!
@kidsafe Жыл бұрын
Orange Seal and not Stan’s Race, my man. That old puncture likely wouldn’t have reopened with Orange Seal.
@Gufolicious2 жыл бұрын
Long story short: you get less punctures but if you get one u are fucked. And yeah, you gotta carry a spare tube anyways.
@jonmaloneycycling75932 жыл бұрын
thanks for sharing
@shekofriends2 жыл бұрын
Are we seeing the demise of tubulars from now on both amateurs and pros then? Secondly why isn't there room for improvement on tubulars, instead we see lots of NEW wheels accompanied by tyres that try to win over the market? Thirdly isn't cycling be open for easiness, less complicated mechanisms, greener behavior where you don't need to throw your 25 away in favor of new(er) standards ( TR, TL.....) Am sure this is not it anyway.
@jonmaloneycycling75932 жыл бұрын
It’s the gluing the Tubs that is really time consuming and changing flats