Turbo Hose Inner Seal Replacement - Peugeot 308 1.6 HDi

[@screwsnutsandbolts]

Here's how to use the Stop & Go Tyre Mushroom Plug Kit: kzbin.info/www/bejne/e2G7mmB7jNKqrtU

[@jamesford6899]

If the pipe comes off would it cause the engine management light to come on and give a boost control fault

[@brunofranco775]

Este tubo quando solto no turbo pode resultar em fumo branco no escapamento?

[@jaggass]

It's probably one of the reason's many 1.6 HDI's sound like tanks.

[@at4466]

loose distribution chain on thp motors make them sound like that

[@jaggass]

I haven't heard many rattle but plenty that sound like that they don't have an air filter. Later Peugeot's 1.6 HDI's are much quieter.

[@at4466]

@@jaggass The T7 HDIs have shitty air filter attachments and the air filter box does rattle when they're broken. But it's a different, thumping kinda rattle. Here's what the THP loose chain sounds like. kzbin.info/www/bejne/q2S4Z2p5aq6FeLM

[@GrooveMushroom]

Hello! Does 1.6 hdi from Peugeot 308 2015 T9 have this sealing?)) And for the same engine maybe you know cure for the rattling air filter box?)

[@screwsnutsandbolts]

I haven't worked on the newer model so I'm not too sure but if it has a turbo it probably has a similar seal. On this model, the air filter housing is pressed down onto rubber mountings and the rear of the filter housing lid has lugs at the back that should fit into slots at the back of the housing before closing the front of it. If it's similar on the newer model it may not be seated correctly of the rubber mounts, or maybe the lid isn't closed right ?

[@michael872uk8]

Hi . I have a 208 1.6 hdi .. with turbo whislte loud.. .. still habe boost just makes horrable noise .. do i change turbo .. and if so is ther anythin else i can put on ????

[@screwsnutsandbolts]

You should really have a mechanic take a look at it just to be sure

[@Passengervehicles]

Good vid

[@screwsnutsandbolts]

Thanks very much !

[@staxuevewot2216]

@ScrewsNutsAndBolts found it at UK's EuroCarParts so glad, hope non of small bits of the old seal didn't get into the turbo yet. There alway is some leaked oil on the engine, which usually comes out middle connection point with the secure clip, no matter how many times an o-rings are being replaced, after some time it start to leak again, do you have any special way to prevent that? o rings don't seem to do the job very well.

[@screwsnutsandbolts]

I can't help you there, sorry. I just changed the seal and nothing more :)

[@staxuevewot2216]

@@screwsnutsandbolts thanks anyway

[@chisty4436]

Use a bigger o ring

[@MDBRK1506]

please whats the benefits of cleaning the turbo and how much kilometers to know when u need to clean ??

[@niccots]

So the turbo bearing is leaking oil, but is so often problem after some time they so they made this seal to not show oil leak to owners and burn all oil in engine or collect it in EGR? How many miles/kms you have on it?

[@screwsnutsandbolts]

There's about 130,000 kms on it

[@niccots]

@@screwsnutsandbolts Nearly the same as mine.

[@NordinIdrisMunir]

same here, 130k so far.. and the turbo bearing is leaking too... so shall i just ignore it?

[@Bootlerov]

Hey y’all! Often misconception. There is no need for premature panic. If you see oil there it DOES NOT MEAN that the turbocharger is seeping oil and dying (however it might be that as well). You have a PCV (positive crankshaft ventilation) inlet right upstream the turbo (design feature) - here is your #1 oil provider in that area starting the first mile. Those Garrets live 200-250 kkm at least unless you ‘help’ cutting their lifespan. You may always check for turbo shaft play with your fingers.

[@BillOdyssey]

I have that ratchet too! Nice vid m8 👍

[@nelsonthekinger]

Niiiceee

[@screwsnutsandbolts]

Thanks !

[@bridgendesar]

what prompted you to change it, looked ok from outside?

[@screwsnutsandbolts]

I had taken it off before and I noticed it had a split in it so I already knew it needed to be replaced :)

[@screwsnutsandbolts]

@Bojan Sobota No I never noticed any different sound from the engine. I just happened to notice it while I was checking something else.

[@thatbig1]

ScrewsNutsAndBolts mines split on my outlander and they don’t do a replacement sleeve want £160 for the full pipe so I’m going to build a replacement intake pip with ally tube and Samco hoses and fit a oil catch tank on the crankcase breather

[@screwsnutsandbolts]

@@thatbig1 Sounds like a plan. Good luck with that ! :)

[@garageprojects9294]

@@thatbig1 or just order one from Amazon for £20 mate

[@lourencobento6582]

My new seal keeps popping off. It's driving me insane 😅

[@screwsnutsandbolts]

Make sure the pipe and seal are clean and dry and don't overtighten it.

[@lourencobento6582]

@@screwsnutsandbolts I think it was the overtightening. Thank you!

[@screwsnutsandbolts]

@@lourencobento6582 You're welcome. I did the same myself lol :)

[@GeorgeBuchan]

I put a new one on and it’s sliding off? !

[@screwsnutsandbolts]

You're probably tightening it too much. Make sure you wipe any oil off the pipe and new seal and only tighten it enough to grip the pipe.

[@rimaslalgerois7411]

Bonjour.spv j'ai pas ce joint sur ma voiture es ce que c'est normal ou il manque merci beaucoup

[@screwsnutsandbolts]

Is it the same model as this 2007 to 2012 Peugeot 308 1.6 HDi ?

[@mkoza76]

Mine keeps popping off no matter how well I clean it or tighten the clip. Anybody else got this issue or know how to fix it?

[@screwsnutsandbolts]

Make sure the pipe is clean and dry and don't over-tighten it. If it's too tight it will pop off eventually

[@mkoza76]

@@screwsnutsandbolts I've cleaned out with degreaser in the past & it only lasted s day or two. I'll try tightening it up less. Thanks!

[@screwsnutsandbolts]

@@mkoza76 I had that same problem and it worked for me. Let me know how you get on

[@mkoza76]

@@screwsnutsandbolts I gave it a good clean yesterday & tightened the clip snug with only a screwdriver as opposed to socket. Took it for about a 20 mile drive & it stayed on. Maybe this has fixed it! I'll give it a couple of weeks & see :) Cheers!

[@screwsnutsandbolts]

@@mkoza76 You're welcome. Hopefully that'll stay on now 👍

[@buraksehitoglu4868]

Part of this seal went in the turbo and damaged it.

[@staxuevewot2216]

actually happened to you? I was afraid same thing can mess up my turbo.

[@Mars2Moon]

I had the same problem, turbo ate my entire pink seal during a hard acceleration , I'm waiting now for the new turbo core and the intercooler because is full of debris from turbo fan and pink rubber. Good job PSA

[@unclemarky3]

pedazo de video ❤️👍🏽👍🏽 si tenes un *308* segui en Instagram *308_official* ahi compartimos nuestros autos... les mando fuerte abrazo Saludos

[@naouiharoun6654]

Thank you