Engine gets assembled, and I am one step closer to installing and getting the bus running! Music- In Audio
Пікірлер: 26
@MH-ev3wr5 ай бұрын
It's easiest to not even deal with the push rod tubes until the heads are on and torqued down. The tubes can go on and off without touching the heads.
@hifivegarage69775 ай бұрын
Yeah I figured that out after, I was used to building upright motors. Now I know! Thank you
@MH-ev3wr5 ай бұрын
@@hifivegarage6977that's why we do it, right? To learn! Now next time you'll be twice as quick.
@muzzcovw7674Ай бұрын
one of the best features of the type 4 vs type 1
@rhettoracle967911 ай бұрын
Hope it runs as pretty as it looks! Great work!
@hifivegarage697711 ай бұрын
Agreed, always taking a risk when you buy a already "built" bottom end.
@juniorclassicvwbugs9245 ай бұрын
Awesome
@hifivegarage69775 ай бұрын
Thank you
@ArrowheadGarage11 ай бұрын
Great video on putting the T4 back together, the only thing that I saw that I would have to disagree with is using the head gaskets. VW issued a service bulletin 30 plue years ago to NOT USE THEM on a Type 4. But other than that, looking good!!!!
@hifivegarage697711 ай бұрын
Good to know!, this motor had them and I've never done them before on any other. I guess we will see how it goes! Thank you for the info!
@muzzcovw7674Ай бұрын
@@hifivegarage6977 Never, never NEVER use those gaskets! As said above haha. They were a terrible idea. I just tore one down last week and two were blown
@hifivegarage6977Ай бұрын
@@muzzcovw7674 so far so good with using them, hopefully I don't jinx it. Thank you though!!!
@muzzcovw7674Ай бұрын
@hifivegarage6977 In a car you can get away with it... but if in a bus, cross your fingers and toes!
@hamishcruden762311 ай бұрын
Great video, I take it you put oil or lube on the o rings when you put them on the push rods... yes cleaning is so important... this is certainly an ideal video for someone rebuilding a VW Combi motor! O, I did laugh when I noticed your puppy would not move and you had to walk all round it... I am often in that position with my pooch 🤣🤣🤣
@hifivegarage697711 ай бұрын
The o rings for the push rod tubes? Yes they were actually in a bag with oil in it prior to installing. And thank you, people are often not fond of these motors but really they are not bad! Also yeah thats just how dogs are....always wanting to be close....or just in the way haha
@jamie-r20344 ай бұрын
As a automatic bus owner as well & still learning, could you at some point take time to explain how to do timing, carb adjustments, etc? I could never find any videos with guys who have automatics! I love to learn how to do it myself.
@julianwinn45026 ай бұрын
Motor looks great
@hifivegarage69776 ай бұрын
Thank you! It's been running great as well!
@jasonburton48711 ай бұрын
coming along ! you could always make a little piece of tin to cover the ac compressor cut out for now
@hifivegarage697711 ай бұрын
Already did :) stay tuned haha
@jasonobispo59216 ай бұрын
Great videos! Any tips/recommendations regarding mounting the Type 4 engine on the engine stand. I have seen posts in forums about how the mounts put stress on the transmission holes. Thanks in advance.
@hifivegarage69776 ай бұрын
I though I showed how I mounted it but I can't find it. Either way I just uses a normal engine stand used the top 2 mounts and drill out where the bottom ones would mount (look in the videos you will see) and I never had issues. They also sell pre made mounts but I know they are expensive that's why I made my own
@MH-ev3wr5 ай бұрын
Also, is there a reason you removed the cooling flaps from the fan housing? Similarly the thermostat, pulley, and cable?
@hifivegarage69775 ай бұрын
This motor didn't have any on it and I only had pieces from the other motor. Decided that being in New mexico ide give it a shot without
@pastblaster3285Ай бұрын
@@hifivegarage6977 You just made a BIG mistake leaving out those flaps ........Just because the geniuses before you left them out does not mean it is ok to follow suit .....Learn how systems work so you can make good decisions ..... Besides not having a motor that will warm up correctly day or night regardless of the state you live in and all the benefits of that like better interior heat in the cold times and even motor expansion of all it's parts , by leaving out the flap on the left side that goes over the oil cooling tower that lays on it's side you just goofed .....How is the fan blown air supposed to make a 90 degree turn downward to go through the oil cooler's vertical openings without that flap ? It won't ....The cooling air will just fly over the top of the cooler ....If you had that flap installed which lays like your cupped hand when in the warmed up position, that flap down, you will notice a gap under the flap's pivot point .....Some of the cooling air will go into that slot and the cupped shape will force that air downward through the cooling tower's vertical openings ..... The original style warm up thermostats are now available new from a great place called "Awesome Powdercoat " ......He also has a pretty good rap about how these work generally on his site ...... Do not try to use the Mexican style thermostats on any aircooled VW motor .......
@ggolds528 күн бұрын
I want to carry a spare Distributor for my 76 Bus. 1800cc fuel injected no electronic ignition. I can't seem to find a Distributor for a type 4 motor with vacuum assist, so that little space ship thing attached. Can you please tell me where I can find this?. Bus Depot and West Coast Metrics aren't sure which one goes with it. Thanks.