Ubiquiti Unifi U6+ Setup | Wifi 6 Access Point Unboxing 📦 Is it for YOU?

Рет қаралды 30,685

Bogdan | Apex One IT

Күн бұрын

Пікірлер: 24

@jsmithepa 4 ай бұрын

Until I watched this, I didn't know about the removable nipple to let the cable through, thanks!

@ApexOneTech 4 ай бұрын

Thank you!

@syberdeath_00 10 күн бұрын

is it ok to use dlink 4 port poe switch? to power up 3 u6+ ?

@mrprfct7069 6 ай бұрын

I bought the LR version and I find the setup ok but the internet speeds throttled way down. When connected to my router. Using the router wifi the speeds are close to 1gig down but when using unifys the speed slows to about 100mb down. All cat6. There is something wrong with these units. Likely will return and just keep using the old routers wifi.

@ApexOneTech 6 ай бұрын

It sounds like you're adding this to a non-UniFi router. You might be throttled on your router LAN port going to the AP. What's your Internet Service Provider's speed promised?

@sunrunnernge560 3 ай бұрын

Subscribed ! Just a fast question. Can I physically run a cat 6 cable from my Router into the WAP, without the need for further hardware ?

@ApexOneTech 3 ай бұрын

Thanks for the sub! If your router has built-in PoE, you can. Otherwise, you need a PoE injector or a PoE switch in between.

@sunrunnernge560 3 ай бұрын

@@ApexOneTech very appreciated!!

@overkillonslash 2 ай бұрын

Is it fine to use tp link poe switch? Unifi switch are much more expensive. Just gonna use it for a basic home setup

@ApexOneTech Ай бұрын

Yeah should be no problem.

@TitoLukason 7 ай бұрын

Hi, is the ceiling mount the same as for UAC-AP-LITE? I mean can i use the old mount or do I need to install the one included?

@ApexOneTech 7 ай бұрын

Yes, same ceiling mount design as UAC-AP-LITE. Identical for the U6 Lite as well. So you should be able to use your existing mount.

@joseangelmendez8496 3 ай бұрын

Hello: I have set up an Access point u6+ from the mobile phone and everything is ok. I have configured it "stand alone", and I access perfectly from the Unifi app, but it has assigned the ip to the device 192.168.1.135 and I want to change it but from the app it does not measure the option and if I try to access from a browser to the address 192.168.1.135 it does not leave me although it does respond to a ping. How can I log in and change your IP address from a browser or from the unifi app on your mobile?

@theridonversus4765 5 ай бұрын

Hi there, can this Ap make a wireless bridge connection? I mean, can it receive a Wifi signal and repeat it?

@ApexOneTech 4 ай бұрын

All UniFi APs can mesh with each other but of course, not as reliable as getting it wired in to your switch.

@teawithb 6 ай бұрын

Can the AP be plugged directly into the USG router? Or does it have to have the additional devices mentioned around the 8 min mark

@ApexOneTech 5 ай бұрын

This does need the additional devices because the USG ports are not PoE. So either a PoE switch or PoE Adapter.

@zhipenghzp3068 6 ай бұрын

Hi are you able to access the CLI for this AP? thank you

@ApexOneTech 5 ай бұрын

Yes, you should be able to SSH into any device but just need to be sure you're on the same network.

@macsuibhne02 6 ай бұрын

I've set up my APs but they are all separate SSIDs to my modem. In my available WiFi connections list I've got a separate option for each AP. Do I need to buy additional devices to mesh everything?

@ApexOneTech 6 ай бұрын

I assume you mean router (or modem)? Are you using a Unifi router? You'll need that.

@macsuibhne02 6 ай бұрын

@@ApexOneTech The modem/router provided by my ISP. I've had one AP connected to it for a couple of years and it worked fine. I could access the UniFi dashboard to get stats, make changes, etc. but a few months ago the AP stopped providing an internet connection, even though it appears connected and discoverable on the network. It looks like it's set up perfectly, just no internet and the dashboard I was getting has now changed to a page trying to sell me devices. I recently bought a second AP, removed the first completely and set up both again as new devices. I'm now seeing my router's SSID as normal but it's duplicated in the available connections list when I've got the APs turned on. This duplicate SSID seems to be coming form the APs. It asks me for the WiFi password but won't connect. The APs are discoverable on the network, have the proper light showing, appear correctly set up in the app but they are doing absolutely nothing and UniFi dashboard is still just trying to sell me Ubiqui products.